Personalized broad learning system for facial expression

Multimedia Tools and Applications - Understanding human emotions through facial expressions is key enabling technology for interactive robots. Most approaches of facial expression recognition are...     

Effects of sintering in a high magnetic field on properties of vitrified bond and vitrified CBN composites

Vitrified bond CBN grinding wheels are being widely used due to their superior performance. Also, advantages of vitrified grinding wheels are high elastic modulus, stable chemical property, and low thermal expansion coefficient. Brittleness and low strength are key factors restricting the development of vitrified bond CBN grinding wheels. In this paper, the sintering in a high magnetic field was innovatively introduced into the manufacturing of vitrified bond CBN grinding wheels, and the effects of sintering in a high magnetic field on properties on vitrified bond and vitrified CBN composites were systematically investigated. Vitrified bond was characterized using three-point bending, scanning electron microscopy, X-ray diffraction. It was observed that microstructure of vitrified bond could be changed, grain orientation could be controlled and average grain size could be decreased in a high magnetic field, while vitrified bond strength could be simultaneously improved. High quality vitrified bond could be obtained by appropriately adjusting the strength and direction of high magnetic field. Results demonstrated that vitrified bond properties were improved when the magnetic field strength was 6?T. In order to highlight the high magnetic field effect on the vitrified CBN composites, the ordinary CBN abrasives and nickel plated CBN abrasives were used respectively. Microstructures, bending strengths of vitrified CBN composites were compared in different high magnetic fields. When the magnetic field strength was appropriate (less than 6?T), the binding characteristic of vitrified bond CBN composites with nickel plated CBN abrasives was greatly improved. The highest bending strength value of vitrified CBN composites was 79.5?MPa in 6?T high magnetic field.     

粉煤灰砖抗折强度测量结果不确定度的评定

通过对粉煤灰砖抗折强度测量结果不确定度的评定,分析出影响试验结果的各种因素,为提高检测水平和精确度提供指导。     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

基于承包商预期收益不变的不平衡报价模型

在招标实践中,通常采用最低价中标原则,使得投标人不得不压低其投标价格。基于承包商预期收益不变的不平衡报价模型,是在“工程量清单报价”的条件下,考虑到施工中工程量的变化及施工顺序的影响,体现了资金的时间价值,在保持承包商预期收益不变的前提下,通过调整各分项工程的单价,来降低工程报价,以增加中标机会而建立的。所建立的模型简单,易于操作,并配以具体的工程实例,通过计算机求得其最优解,可供承包商投标报价时参考。     

动态规划原理在骨料用料方案设计中的应用

在砂石料场规划中常面临多供料点、多需料点条件下的用料方案设计问题。本文应用动态规划原理,提出了“多供点—多需点”物料调配优化计算方法及框图,编制了相应的计算程序。工程实例分析表明,该方法在骨料综合成本和弃料量等方面均优于常规方法,具有一定的应用价值。     

炼油达标污水回用处理试验研究

采用曝气生物滤池、多介质过滤、超滤、反渗透工艺,对炼油达标外排污水进行回用处理中试试验。结果表明,曝气生物滤池对油、COD和浊度去除效果良好,超滤、反渗透膜化学清洗周期达到 2个月以上,脱盐率稳定在98％以上,产水品质达到回用要求。