豫西雷门沟钼矿水文地质条件分析及涌水量预测

豫西熊耳山雷门沟钼矿床位于东秦岭多金属成矿带东段,是已探明的超大型斑岩型钼矿,前人研究程度高、地质成果丰硕,但对矿床开采技术条件方面研究较少。本次通过地质调查工程、水文地质试验等方法,从水文地质角度,对雷门沟钼矿床水文地质条件进行研究,填补了该方面的空白,丰富了研究成果；采用水文地质比拟法预测未来矿坑最大排水量2613 m³/d,经实践检验结果较为可靠；总结的采坑排水量预测方法、含水层特点、矿床充水因素以及防治水措施,以期对该区域水文地质工作具有参考价值。     

Bamboo biochar-catalytic degradation of lignin under microwave heating

Abstract

Lignin biochar-catalytic depolymerization using biochar Fe-600, Fe-800, Ni-600, Ni-800 catalysts under microwave-heating (180?°C for 30?min) was explored in an ethanol/formic acid (1:1) media. Non-catalyst depolymerization was also studied and compared with the biochar-catalysts results. Characteristics of the bio-char catalysts were analyze by BET, XRD, and FT-IR. GPC, FT-IR, and MALDI-TOF MS spectrometry were also used to characterize the depolymerization products. The experimental results showed that the S_BET, V_t, and V_mec and average pore diameter of the biochars are considerably dependent on the preparation temperature and type of cation (Ni²⁺ or Fe³⁺). The maximum yield of bio-oil product was obtained as 85?wt% with the addition of biochar Ni-600 and the total amount of oligomers or monomers with a molecular weight of 164 to 446 reaches 80.4%.     

基于Isograph的FMECA分析在潜孔钻机中的应用

为提高潜孔钻机的可靠性,利用FMECA分析方法并结合Isograph软件对潜孔钻机进行FMECA分析。通过对潜孔钻机FMECA分析,确定了潜孔钻机危害性最高的组成结构,提出了预防维护的措施,为提高潜孔钻机的可靠性提供了依据。     

一种压力容器设计的优化方法

当压力容器内体积一定时,利用给出的内体积公式,在一定范围内改变壳体内径及筒体长度(筒体与两封头焊缝间距离),按照GB 150-1998《钢制压力容器》有关规定可得到壳体壁厚一定但内径和筒体长度不同时相应的壳体质量。根据壳体质量的大小并综合考虑其它因素,是选择最佳设计方案的有效途径。     

小型机载数字视频记录系统的设计与实现

采用嵌入式控制模块SOM2386和专用视频处理芯片SZ1510,设计和实现了一种基于电子硬盘存储的嵌入式小型机载数字视频记录系统。给出了系统总体方案,阐述了视音频解码编码、接口、控制及存储单元的硬件设计,介绍了系统的软件设计,并给出了系统软件的整体工作流程。该系统体积小、重量轻、抗震性好、使用维护方便,已在某型飞机上得到应用。     

井下煤仓全深度分段爆破成井技术

介绍了在煤矿现有设备条件下，全深度一次钻孔分段爆破掘进煤仓的设计与应用情况，论述了爆破方案确定，参数设计及主要措施，通过实践取得了良好效果。     

Microstructure-Property Correlation in AI_4C_3 Dispersion Strengthened Al Composite

The microstructure and tensile properties of Al_4C_3 dispersion strengthened Al composite fabricatedby reaction milling technique were investigated.It is indicated that the rod-like Al_4C_3 dispersoidshaving a diameter of 0.02-0.03 μm and a length of 0.1-0.3μm are formed by reaction of C with Al,and uniformly distributed in the Al matrix.The interface between Al_4C_3 and Al is clean and theinterfacial bonding is good.The matrix consists of the subgrains which have the size of 0.3-0.4μm,and most of the Al_4C_3 dispersoids are distributed on the subgrain boundaries.The 11 vol.-%Al_4C_3/Al composite exhibits an UTS (ultimate tensile strength) of 400 MPa and anelongation-to-failure of 8.0%.     

生物分解性纤维及其应用

本文介绍了生物分解性纤维所用的树脂，生产方法及应用。