Low-bandgap copolymers consisting of 2,1,3-benzoselenadiazole and carbazole derivatives with thiophene or selenophene π-bridges

Two donor–acceptor-type alternating copolymers consisting of 2,1,3-benzoselenadiazole and carbazole derivatives with thiophene or selenophene π-bridges were synthesized by Suzuki cross-coupling polymerization, and their optical, electrochemical, and photovoltaic properties were compared. The selenophene π-bridged copolymer (PCz-DSeBSe) exhibited a smaller band-gap (1.82 eV) than the thiophene-bridged polymer (PCz-DTBSe; 1.89 eV). PCz-DSeBSe also showed a deeper highest occupied molecular orbital energy level (−5.36 eV) than PCz-DTBSe (−5.20 eV). Moreover, the PCz-DSeBSe thin film showed higher crystallinity and hole mobility than the PCz-DTBSe thin film. Organic photovoltaic devices were fabricated using the polymers as the donors and [6,6]-phenyl-C₇₁-butyric acid methyl ester (PC₇₁BM) as the acceptor. The device using PCz-DSeBSe showed a higher open circuit voltage (V_oc), short circuit current density (J_sc), and power conversion efficiency (PCE) than that using PCz-DTBSe. The fabricated indium tin oxide/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)/PCz-DSeBSe:PC₇₁BM/LiF/Al device showed the maximum PCE of 2.88% with a J_sc of 7.87 mA/cm², an V_oc of 0.80 V, and a fill factor of 0.50 under AM 1.5G irradiation (100 mW/cm²).     

Multigroup pin power reconstruction with two-dimensional source expansion and corner flux discontinuity

A pin power reconstruction method that is readily applicable to multigroup problems with superior accuracy is presented for applications involving rectangular fuel assemblies. It employs a two-dimensional (2D), fourth order Legendre expansion of the source distribution that naturally leads to a group-decoupled, 2D semi-analytic solution of the neutron diffusion equation. The four surface average currents and four corner fluxes are used as the boundary conditions to uniquely specify the homogenous solution. The corner fluxes and source expansion coefficients are iteratively determined using the condition of corner point balance and the orthogonal property of the Lengedre functions. Corner discontinuity is incorporated in the calculation of the corner fluxes which turns out to be very effective in the cases of enrichment zoning. The accuracy of the proposed method is assessed by performing the two-step core calculations for the L336C5, C5G7MOX, and MOX core transient benchmark problems and then by comparing with the direct whole-core transport solutions. The results indicate that the proposed method is as accurate as the fully analytic method and works well irrespective the number of groups. However, it is also noted that somewhat larger errors are inevitable at the peripheral assemblies near the reflector in which the error associated with a prioi generation of the homogenized cross-sections and form functions is not trivial.     

Antimicrobial resistance of Escherichia coli O157 from cattle in Korea

Of 45 Escherichia coli O157 isolates from cattle feces, which were collected between May 2000 and September 2003 in Korea, 32 were resistant to at least 1 antibiotic and 28 were resistant to 4 or more antibiotics, with 32, 30 and 30 of the isolates being resistant to streptomycin, tetracycline and sulfisoxazole, respectively. Two isolates were resistant to fluoroquinolones and to 10 or more of the 22 other antimicrobial agents that were tested. Thirteen antimicrobial resistant patterns were observed. The most frequent resistance type, which was found for 11 isolates, was streptomycin-tetracycline-kanamycin-ampicillin-piperacillin-cephalothin-sulfisoxazole-ticarcillin. Polymerase chain reaction (PCR) analysis of the isolates for E. coli O157 virulence markers revealed that 25 of the resistant E. coli O157 isolates tested positive for stx2 or both stx1 and stx2 genes. These findings suggest that many of the resistant E. coli O157 isolates might cause disease in humans.     

A study on an equivalent model of the threaded fasteners in complex structures through tightening and loosening analysis

Journal of Mechanical Science and Technology - The threaded fasteners are typical machine components in tightening of the machine parts and structures. In addition, as threaded fasteners are easy...     

Simultaneous Formation of Ohmic Contacts on p +- and n +-4H-SiC Using a Ti/Ni Bilayer

In this work, Ti/Ni bilayer contacts were fabricated on both p ⁺- and n ⁺-4H-SiC formed by ion implantation, and the effects of the Ti interlayer on the contact resistance and interfacial microstructure were studied. Adoption of a thin (10 nm) Ti interlayer resulted in specific contact resistance of 4.8 μΩ cm² and 1.3 mΩ cm² on n ⁺- and p ⁺-4H-SiC, respectively, comparable to the values for contacts using only Ni. Moreover, contacts using Ti/Ni provide a flat and uniform interface between Ni₂Si and SiC, whereas discontinuous, agglomerated Ni₂Si islands are formed without the use of a Ti interlayer. In addition, the Ti interlayer was demonstrated to effectively dissociate the thin oxide film on SiC, which is advantageous for low-resistance, reliable ohmic contact formation. In summary, use of a Ti/Ni bilayer is a promising solution for one-step formation of ohmic contacts on both p ⁺- and n ⁺-4H-SiC, being especially suitable for SiC n-channel metal-oxide-semiconductor field-effect transistor (nMOSFET) fabrication.     

Novel Digital Nonvolatile Memory Devices Based on Semiconducting Polymer Thin Films

Recent increases in the demand for mobile devices have stimulated the development of nonvolatile memory devices with high performance. In this Communication, we describe the fabrication of low‐cost, high‐performance, digital nonvolatile memory devices based on semiconducting polymers, poly(o‐anthranilic acid) and poly(o‐anthranilic acid‐co‐aniline). These memory devices have ground‐breaking and novel current–voltage switching characteristics. The devices are switchable in a very low voltage range (which is much less than those of all other devices reported so far) with a very high ON/OFF current ratio (which is on the order of 10⁵). The low critical voltages have the advantage for nonvolatile memory device applications of low operation voltages and hence low power consumption. With this very low power consumption, the devices demonstrate in air ambient to have very stable ON‐ and OFF‐states without any degradation for a very long time (which has been confirmed up to one year so far) and to be repeatedly written, read and erased. Our study proposes that the ON/OFF switching of the devices is mainly governed by a filament mechanism. The high ON/OFF switching ratio and stability of these devices, as well as their repeatable writing, reading and erasing capability with low power consumption, opens up the possibility of the mass production of high performance digital nonvolatile polymer memory devices with low cost. Further, these devices promise to revolutionize microelectronics by providing extremely inexpensive, lightweight, and versatile components that can be printed onto plastics, glasses or metal foils.     

Treatment of taste and odor material by oxidation and adsorption.

Massive blooms of blue-green algae in reservoirs produce the musty-earthy taste and odor, which are caused by compounds such as 2-MIB and geosmin. 2-MIB and geosmin are rarely removed by conventional water treatment. Their presence in the drinking water, even at low levels (ng/L), can be detected and it creates consumer complaints. So those concentrations have to be controlled as low as possible in the drinking water. The removals by oxidation (O3, Cl2, ClO2) and adsorption (PAC, filter/adsorber) were studied at laboratory and pilot plant (50 m3/d) to select suitable 2-MIB and geosmin treatment processes. The following conclusions were derived from the study. Both of the threshold odor levels for 2-MIB and geosmin appeared to be 30 ng/L as a consequence of a lab test. For any given PAC dosage in a jar-test, removal efficiencies of 2-MIB and geosmin were increased in proportion to PAC dosage and were independent of their initial concentration in raw water for the tested PAC dosages. In comparison of geosmin with 2-MIB, the adsorption efficiency of geosmin by PAC was superior to that of 2-MIB. The required PAC dosages to control below the threshold odor level were 30 mg/L for geosmin and 50 mg/L for 2-MIB at 100 ng/L of initial concentration. Removal efficiencies of odor materials by Cl2, ClO2, and O3 were very weak under the limited dosage (1.5 mg/L), however increased ozone dosage (3.8 mg O3/L) showed high removal efficiency (84.8% for 2-MIB) at contact time 6.4 minutes. According to the initial concentrations of 2-MIB and geosmin, their removal efficiencies by filter/adsorber differed from 25.7% to 88.4%. For all those, however, remaining concentrations of target materials in finished waters were maintained below 30 ng/L. The longer run-time given for the filter/adsorber, the higher the effluent concentration generated. So it is necessary that the run-time of the filter/adsorber be decreased, when 2-MIB or geosmin occurs in raw water.     

UNSTRUCTURED FINITE-VOLUME METHOD FOR RADIATIVE HEAT TRANSFER IN A COMPLEX TWO-DIMENSIONAL GEOMETRY WITH OBSTACLES

The radiative heat transfer in a complex two-dimensional enclosure with obstacles with participating medium is very important in practical engineering applications. In order to deal with this problem, in this study the finite-volume method (FVM) for radiation has been derived using the unstructured grid system. A general discretization equation was formulated by introducing the directional weight and the step scheme for spatial differencing. For its comparison and validation, two test cases, an equilateral triangular enclosure and a square enclosure with baffle, were chosen. Then, more complex and practical cases, such as a semicircular enclosure with cylinder hole, a square enclosure with finned internal cylinder, and a furnace with embedded cooling pipes, were investigated. All the results obtained by the unstructured FVM agreed very well with the exact solutions as well as the results obtained by the zone method. Furthermore, the wiggling behavior occurring in the blocked-off FVM was not produced by the unstructured FVM. Three types of manipulation of control angle overlap were also examined here. It was found that the solutions depended on the type of manipulation of control angle overlap, especially when the number of control angles was small. Usually, both the pixelation method and exact treatment introduced here yielded better solutions than the bold approximation.     

Improvement strategy for edge waviness in roll bending process of corrugated sheet metals

This paper focuses on the corrugated thin-walled sheet metal in the roll bending process. The main defect that appears in corrugated panels subjected to high amounts of bending deformation is a wavy edge. Edge defects are caused by excessive longitudinal stress and strain near the edge of the plate, and local edge buckling may occur when some critical value of the bending radius is exceeded. This paper proposes two different approaches to avoid a wavy edge for a formed panel: excessive stress on the edge region is restrained by controlling the length of the cross-sectional end of the corrugated panel while considering the stress distribution, and the bending radius in each forming step is determined by considering the strain limit at which the initial edge waviness occurs to avoid excessive compression at particular steps. The experimental and numerical results indicated that the two proposed design strategies can minimize wavy edges in the formed shape.     

A simple background elimination method for Raman spectra

In this paper, we consider a new background elimination method for Raman spectra. The proposed method is based on peak detection, smoothing, and interpolation. Since the background is usually slowly varying with respect to wavelength, we could estimate the background by eliminating significant peaks. For this purpose, we seek the peaks by inspecting the smoothed derivative of a given spectrum. After clipping out the corresponding peak regions, we estimate the background by applying a modified linear interpolation. Then the background is eliminated from the measured Raman spectrum by simple subtraction. The experimental results showed that the proposed method gave satisfactory results for real Raman spectra as well as synthetic data. As the proposed method requires no prior knowledge of spectrum, we expect that the method could be applied to other spectral data as well.