The influence of nickel and copper on the austempering of ductile iron

In the present investigation, the effect of alloying elements on the austempering process, austempered microstructure, and structural parameters of two austempered ductile irons (ADI) containing 0.6% Cu and 0.6% Cu/1.0% Ni as the main alloying elements was investigated. The optical metallography and x-ray diffraction were used to study the changes in the austempered structure. The effect of alloying additions on the austempering kinetics was studied using the Avrami equation. Significantly more upper bainite was observed in the austempered Cu-Ni alloyed ADI than in Cu alloyed ADI. The volume fraction of retained austenite (X _γ), the carbon level in the retained austenite (C _γ), and the product X _γ C _γ in an austempered structure of Cu-alloyed ADI are higher than in Cu-Ni-alloyed ADI. The austempering Kinetics is slowed down by the addition of Ni.     

A multisource energy harvesting utilizing highly efficient ferroelectric PMN-PT single crystal

This paper demonstrates a multi-source energy harvester that is able to utilize simultaneously both piezoelectric and pyroelectric effects in lead magnesium niobate-lead titanate (PMN-PT) single crystal. The paper presents a study of PMN-PT single crystal with a (67:33) composition grown in our laboratory via a vertical gradient freeze method without any flux. The performance of the piezoelectric and pyroelectric energy harvester using unimorph device structure was evaluated via modeling and experiment. The theoretical study was implemented based on a distributed parameter electromechanical model and the modelling procedure was approximated using finite element analysis to predict the electromechanical behavior of the harvester. The maximum power density at a resonance frequency of 50 Hz and optimum resistance of 2 MΩ was 16.7 nW/(g² cm³) under a 1 g acceleration of vibration. The measured values of electrical output parameters were in good agreement with theoretical and modelling results using MATLAB and COMSOL Multiphysics, respectively. By using the pyroelectric effect along with the piezoelectric effect, the output voltage of the energy harvester was found to be enhanced at the optimum resistance and specific frequency values. It was noticed that the output voltage was increased monotonically with temperature-difference (ΔT) and reaches up to 180 % of its original value under temperature difference of 1.7 °C at a frequency value of 49 Hz.     

Location of nucleolar organizing regions on the chromosomes of the Syrian hamster (Mesocricetus auratus) and the Djungarian hamster (Phodopus sungorus)

Terminal chromosome associations ("satellite associations") in ASG-banded preparations have been used to determine the number and location of staellites in the Syrian hamster (Mesocricetus auratus) and the Djungarian hamster (Phodopus sungorus). Five pairs of satellites are found in the former and four in the latter. Nucleolar organizing regions (NORs) were visualized with the Ag-AS silver precipitation technique, and their number and position corresponded exactly with the number and position of satellites in Phodopus, where positive chromosome identification can be made in the absence of banding. Numerical agreement is exact in Mesocricetus as well, and the morphology of the silver-tagged NOR-bearing chromosomes strongly suggests that corrrespondence also occurs in this species.     

Natural frequencies of functionally graded plates by a meshless method

We use the global collocation method, the first and the third-order shear deformation plate theories, the Mori–Tanaka technique to homogenize material properties, and approximate the trial solution with multiquadric radial basis functions to analyze free vibrations of functionally graded plates. Frequencies computed by the present method are found to agree well with those from the analytical solution of Vel and Batra, and the numerical solution of Qian et al. based on the meshless local Petrov–Galerkin formulation.     

Multi-objective optimization of the ecm process

Optimization of process parameters is helpful in efficient working of the process and, hence, in lowering the cost of machining. Optimization of ECM process parameters has been achieved by considering only one objective at a time from metal removal rate, geometrical accuracy, and total process cost. From a practical point of view, a solution of the ecm problem satisfying all three objectives simultaneously is highly desirable.In the proposed model, a multi-objective problem involving the ecm process is formulated producing highly nonlinearized equations. These are then linearized by regression analysis and converted into a goal programming format. Finally, the problem is solved by the partitioning algorithm.It is concluded that the tool, or cathode, remains safe at the optimal values of design variables obtained in the examples discussed. The optimal value of voltage when metal removal rate is the only objective, is found to be higher than the case when the geometrical accuracy requirement is also to be satisfied.     

Phase‐shifting differential interference contrast microscope with Savart shear prism and rotatable analyser

A novel differential interference contrast microscope (DICM) is proposed in this research. It is constituted by inserting a Savart shear prism between the objective and sample of a polarising microscope having a rotatable analyser as the phase‐shifter, and it is with the ability to enhance image contrast using the principle of shearing interferometry. This letter is to introduce the configuration, interpret the interference patterns and present the experimental setup of the DICM. In addition, this letter is to display the experimental results from the uses of the setup; the results demonstrate the validity and ability of the DICM.     

Quasistatic indentation of a rubber-covered roll by a rigid roll

The nonlinear elastic problem involving the indentation of a slightly compressible rubber-like layer bonded to a rigid cylinder and indented by another rigid cylinder is analysed by the finite element method. Both the geometric and material nonlinearities are accounted for. The finite element formulation of the problem is based upon a variational principle recently proposed by Cescotto and Fonder, and is valid for both slightly compressible and incompressible materials. The results computed and presented graphically include the shape of the indented surface, the pressure distribution over the contact surface, and the stress distribution at the bond surface. For the same contact width, the results for the compressible material are found to differ significantly from those for the case when the rubber-like layer is assumed to be incompressible.     

Factors affecting length of herdlife in purebred and crossbred dairy cattle

The proportional hazards model with censoring was used to assess the effects of breeding value, disease, calving, size, and udder and lactation traits on length of herdlife of 3881 heifers in five herds. Data were recorded over 10 yr from three lines: a Holstein line, an Ayrshire-based line, and a crossbred line. Influences on survival were assessed from data collected at birth, 34, 50, and 82 wk, first freshening, and at 112 and 308 d postpartum. Median estimated herdlife (age at 50% culling) was 3.9 yr for animals alive at first freshening and increased to 4.3 yr for those that completed a first lactation (308 d postpartum). Herds differed greatly in the pattern of culling after freshening. Crossbred females had 21 wk longer median estimated herdlife than the mean of the purelines at 308 d postpartum. Individual milk yield was positively associated with longevity and had the greatest impact on length of herdlife. Abortion and fertility measured as days to last insemination were negatively associated with length of herdlife. Large heifers tended to have increased longevity. High feed intake postpartum was associated with reduced length of herdlife. Objective measures of conformation, which included measurements of the udder, were not important in determining herdlife.     

Growth and feed efficiency of pureline and crossline dairy heifers

Data on 3957 heifers from the Holstein H line, Ayrshire-based A line, and C line (crossbreds between H and A lines) were used. Growth, feed consumption, and feed efficiency from 26 to 34 wk were examined. The full model included the fixed effects of herd, year of birth, season of birth, and additive, maternal, and heterotic genetic effects with 26-wk weight as a covariate. Heterotic and maternal effects were not significant. Adjusted for the 26-wk weight covariate, H line heifers gained 3 kg more than A line heifers with C line heifers intermediate. Adjusted for 26 and 34-wk weight covariates, H line heifers ate 2 kg less TDN than A line heifers and, hence, were more efficient. Correlations among traits were estimated using the residual variance-covariance matrix from the full model. Body weight at 34 wk was correlated with 26-wk weight (r = .88) but essentially independent of rate of gain (r = .02). It was correlated with feed consumed (r = .51) and negatively associated with gain/feed consumed (r = -.25). Gain was correlated (r = .84) with gain/feed consumed but mildly so (r = .28) with feed consumed. Feed consumption was negatively correlated (r = -.25) with gain/feed consumed when the 26-wk weight covariate was included but became much larger (r = -.95) when both 26 and 34 wk weight covariates were included. Although genetic differences in feed consumption and feed efficiency of growing heifers exist, these are small and closely associated with weights and weight gains.