埋地管道泄漏内封堵装置设计与研究

针对流体输送埋地管道泄漏问题,设计了一种利用管道机器人携带封堵气囊进行快速应急封堵修复的埋地管道泄漏内封堵装置。采用矩阵变换方法建立了牵引系统驱动轮过弯方程,利用MATLAB软件对过弯方程进行了验证,同时利用ADAMS软件仿真分析过弯路径与驱动轮转角对牵引系统行走速度的影响。研究结果表明:由两个串联封堵器组成的应急封堵系统可满足复杂工况下的管道泄漏封堵要求;牵引系统驱动轮在弯管内部行走时,单轮速度呈周期性变化,但三个驱动轮整体周期运动特性一致;驱动轮转角在25°~40°时,牵引系统行走速度与驱动轮转角成正比,且转角为30°时驱动效果最好。该内封堵装置的结构设计可为管道泄漏应急封堵领域装备的研发提供重要参考。     

Optimal Guaranteed Cost Tracking of Uncertain Nonlinear Systems Using Adaptive Dynamic Programming with Concurrent Learning

In this paper, based on adaptive dynamic programming (ADP) with concurrent learning, the problem of optimal guaranteed cost tracking is studied for a class     

An airlight estimation method for image dehazing based on gray projection

Multimedia Tools and Applications - As the key parameter of dehazing algorithms, airlight value directly affect the calculation accuracy of sky region, and any deviation will lead to the chromatic...     

基于图像增强的去雾快速算法的FPGA实现

基于图像增强方法，本文提出了一种使用亮度映射的图像去雾快速算法。此算法通过调整室外多雾场景图像的对比度，提高了雾中物体的辨识度。算法的复杂度低、处理延迟小，实时性高，利于FPGA的实现。实现时不需外存储器，延时为ns级，并提供了强度调节接口，以适应较广的应用环境。     

Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

含煤盆地深层“超饱和”煤层气形成条件

中国深层煤层气资源丰富，但总体勘探和认识程度较低，尚未形成较为系统的深层煤层气地质理论。通过解剖分析准噶尔盆地白家海凸起和鄂尔多斯盆地临兴区块深层"超饱和"煤层气井的试气/生产动态，估算原地游离气的含气量，分析了深层"超饱和"煤层气的形成条件。研究表明：①深层"超饱和"煤层气储层中除吸附气外，还含有原地游离气，用常规试气方法可直接获得气流，煤层气的产出不明显依赖于排水降压；②埋藏超过一定深度，在煤阶和温度的综合作用下，煤的吸附能力将随埋深的继续增加而降低，煤层中吸附气的饱和度有增加的趋势，在达到吸附饱和后，出现原地游离气并形成"超饱和"煤层气，盆地深层具有"超饱和"煤层气形成的优势条件；③由于地温梯度和压力梯度的不同，不同盆地"超饱和"煤层气出现的临界深度不同，异常高压和异常高热流可以降低深层"超饱和"煤层气形成的临界深度；④深层"超饱和"煤层气开发具有大大缩短见气时间、充分利用地层能量和累积产水量低等优势，有望成为未来煤层气勘探开发的一个重要领域。     

Cross-Layer Optimization of Dynamic Packet Assignment for Video Transmission Over IEEE 802.11e Networks

Video transmission over IEEE 802.11e wireless networks still shows poor performance for large bandwidth demand and frequently changed environments. Thus, several enhancements of IEEE 802.11e were proposed. On the other hand, big frames and simultaneous sending of adjacent frames always cause packet dropping for buffer overflow. In the past, we proposed an IEEE 802.11e enhancement named DFAA and a content aware mechanism to solve the above problems. The motivation of this paper is to find a proper way to integrate these two mechanisms. A DFAA enhancement (DFAA-E) is proposed to make up the insufficiency of content aware mechanism. Experiments results show that the combination of DFAA-E and content aware mechanism improves the video decoded quality greatly. And its performance can be further enhanced by selecting the suitable settings of certain parameters.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.