Growth of ZnO nanowires in hollow-type magnetron O2/Ar RF plasma

In this study we investigate how the sputtering of zinc from a zinc target is influenced by the properties of O₂/Ar plasma when the discharge parameters such as gas pressure ratio and target bias voltage are changed. We also investigate plasma conditions for the formation of ZnO nanowires that are created and deposited on the substrate. We found that a plasma condition with strong optical emission from Zn neutrals is an important factor for the deposition of ZnO nanowires. Both the growth of nanowires and the emission intensity from Zn strongly depend on the partial pressure of oxygen.     

Integrity evaluation of glass-fiber composites with varied fiber/matrix interfacial strength using acoustic emission

An advanced acoustic emission analysis method was used to study the dynamics and sequence of microfractures in uni-directional glass-fiber reinforced plastics (UD-GFRPs). UD-GFRPs (60 wt% fiber) with different interfacial qualities were prepared by adding a small amount (4 or 8 wt%) of paraffin wax into vinylester matrix without affecting much the mechanical properties of the matrix. The orientation dependence of both the P-wave velocity and attenuation were accurately measured by the laser ultrasonic method, and incorporated into the acoustic emission analysis of visco-elastic media. The analysis iteratively compares the acoustic emission signals (measured as out-of-plane displacements) with theoretical waveforms calculated assuming the time history and type of an acoustic emission source. The waveform simulation allows us to estimate the fracture dynamics and the sequence of the Mode-I fiber fracture (Type 1), Mode-I debonding (Type 2) and Mode-II disbonding (Type 3). The fiber fracture in UD-GFRPs without wax started at 0.1% strain. The initiation strain increased to 0.25 and 0.3% in the specimens with wax. The specimens with lower interfacial strength showed rapid succession of microfractures at higher stresses (above 100–200 MPa). Fracture dynamics showed distinct differences by wax addition. Using the present analysis method, we can determine quantitatively effects of interfacial quality on the microfracture processes and assess the integrity of UD-GFRPs.     

金属三维微结构加工技术的研究

三维微结构制作技术是MEMS加工的关键技术之一.现有的三维微细加工技术主要有利用SU-8等光刻胶形成的以IC工艺为基础的硅三维微结构制作技术和以同步辐射X射线曝光为基础的LIGA技术.但是,在传统的去胶液中,SU-8光刻胶会膨胀变形,从而可能导致图形的失败.而LIGA技术需要昂贵的同步辐射光源和特制的LIGA掩模板,加工周期长.为此,基于反应离子深刻蚀技术,结合电镀工艺,提出了一种金属微结构的微加工制作方法,并进行了相应的实验.结果表明,该方法不仅可以制造出深宽比为6的微型金属螺旋线圈,还可以为其他非硅三维微结构的加工提供一定的技术支持.     

Identification and field evaluation ofAnomala octiescostata (Coleoptera: Scarabaeidae) sex pheromone

Using GC-EAD, the sex pheromone of the scarab beetleAnomala octiescostata was identified to be a 8:2 binary mixture of (R,Z)-5-(–)-(oct-1-enyl)oxacyclopentan-2-one and (R,Z)-5-(–)-(dec-1-enyl)oxacyclopentan-2-one. These semiochemicals have been also reported as sex pheromone constituents of otherAnomala species, either geographically or seasonally isolated fromA. octiescostata. Synthetic sex pheromone was highly attractive in the field; 0.1 mg captured significantly more males than two virgin females. Buried traps were significantly more attractive than those positioned at 30, 90, and 150 cm above the ground. In a dose-response test (0.1–100 mg), no saturation due to overdose of pheromone was observed, but in most cases, two dosages differing by 10-fold were not significantly different. Response of males to traps baited with different ratios of the two components was tested in two experiments with randomized blocks and Latin-square designs. Deviation from the natural ratio (8:2) of sex pheromone did not significantly diminish the response of males. Peak flight activity of beetle was recorded at 9:00–10:00 AM JST on sunny days in the end of April 1993.Presented in part at the 10th Annual ISCE Meeting, July 31–August 4, 1993, Clearwater Beach, Florida.     

Synthesis and properties of bis(sodium sulfonated ester) types of cleavable surfactants derived from 1-O-alkylglycerols

Novel sulfonated ester types of cleavable surfactants were easily prepared by acid-catalyzed esterification of 1-O-alkylglycerols with bromocarboxylic acids, followed by the Strecker reaction. These surfactants have good solubility in water. Though this series of cleavable surfactants are divalent in type, they show good micelle formation and the ability to lower surface tension. The solubility of these surfactants in hard water was more than 10 times higher than sodium 1-dodecanesulfonate. They decompose quickly and completely in 0.5 M NaOD. Their biodegradabilities were higher or almost the same as that of sodium 1-dodecanesulfonate.     

Reduction of NRRO in ball bearings for HDD spindle motors

In this paper, it is theoretically and experimentally analyzed that the non-repetitive run-out (NRRO) of a ball bearing is caused by geometrical errors of the inner and outer races and the balls, and the number of balls.

The results are summarized as follows:

(1) As for the geometrical errors of the inner and outer races, it is possible to reduce the NRRO to be less than 1 nm by choosing 12 or 18 number of balls, even if the inner and outer races have a harmonic undulation of less than the 11th order.

(2) The NRRO of a ball bearing with 12 balls is very small even if the geometrical errors of ball bearing parts are large. It was confirmed that 12 was an optimal number of balls for ball bearings used for HDD spindle motors.

     

Cementation of Sands Due to Microbiologically-Induced Carbonate Precipitation

In this study, microbial precipitation of carbonate was observed using high microbial urease activity, and it was found that the ratio of Mg/Ca affected the types of crystals produced. Without Mg²⁺, calcite was produced using only CaCl₂, while the presence of Mg produced Mg-calcite, magnesite and/or possibly dolomite of round, spherical or fibrous shapes, depending on reaction time, pH and Mg/Ca ratio. The carbonate produced contributed to the development of cementation for sands. The presence of Mg showed a relatively strong cementation of the carbonate.     

Bending fatigue strength of case-carburized helical gears with large helix angles up to 40 degrees

Case-carburizing of helical gears with large helix angles may form too large hardened layers near the tooth width end on the acute angle side (ACUTE-END), and adversely affect the bending fatigue strength. We investigated the bending fatigue strength of casecarburized helical gears with large helix angles up to approximately 40° through a bending fatigue test, hardness test, and residual stress measurement. We found that the case-carburizing formed large hardened layers near ACUTE-END, reduced the compressive residual stress near ACUTE-END, and restricted the improvement of the bending fatigue strength in a meshing state where tooth root stress became large near ACUTE-END. Based on the obtained bending fatigue limits, we revealed that ISO 6336-3:2006 overestimated the rate of increase of the permissible circumferential loads for helix angles exceeding approximately 30°, and ISO/DIS 6336-3:2018 underestimated this rate for helix angles near 30°.

     

Atomically resolved imaging by low-temperature frequency-modulation atomic force microscopy using a quartz length-extension resonator

Low-temperature ultrahigh vacuum frequency-modulation atomic force microscopy (AFM) was performed using a 1 MHz length-extension type of quartz resonator as a force sensor. Taking advantage of the high stiffness of the resonator, the AFM was operated with an oscillation amplitude smaller than 100 pm, which is favorable for high spatial resolution, without snapping an AFM tip onto a sample surface. Atomically resolved imaging of the adatom structure on the Si(111)-(7x7) surface was successfully obtained.     

Multiple evaluations of the removal of pollutants in road runoff by soil infiltration

Groundwater replenishment by infiltration of road runoff is expected to be a promising option for ensuring a sustainable urban water cycle. In this study, we performed a soil infiltration column test using artificial road runoff equivalent to approximately 11-12 years of rainfall to evaluate the removal of pollutants by using various chemical analyses and bioassay tests. These results indicated that soil infiltration treatment works effectively to remove most of the pollutants such as organic matter (chemical oxygen demand (CODMn) and dissolved organic carbon (DOC)), P species, polycyclic aromatic hydrocarbons (PAHs), numerous heavy metals and oestrogenic activities. Bioassay tests, including algal growth inhibition test, Microtox and mutagen formation potential (MFP) test, also revealed effective removal of toxicities by the soils. However, limited amounts of NO3, Mn, Ni, alkaline earth metals, perfluorooctane sulphonate (PFOS) and perfluorooctane sulphonamide (FOSA) were removed by the soils and they possibly reach the groundwater and cause contamination.