Phase-Field Modeling of Nugget Zone for a AZ31-Mg-Alloy Friction Stir Weld

This work presents simulation of microstructure evolution in the nugget zone (NZ) of a AZ31-Mg-alloy friction stir weld. The process parameters (tool geometrical characteristics, rotational speed, travel speed, applied load) have been correlated with the resulting microstructural features in the NZ of the weld (grain size and population) with the aid of the MICRESS software, which provides the ability to simulate both nucleation and grain growth during dynamic recrystallization phenomena evolving in the NZ during the weld thermal cycle. The input parameters of the developed model include the tool geometry, the welding conditions as well as the recrystallization energy, the grain boundary mobility and specific material properties. NZ microstructure obtained by simulation shows good agreement with experimental measurements for both grain population and size.     

Three‐dimensional color prediction modeling of single‐ and double‐layered woven fabrics

In this research, the three‐dimensional structural and colorimetric modeling of three‐dimensional woven fabrics was conducted for accurate color predictions. One‐hundred forty single‐ and double‐layered woven samples in a wide range of colors were produced. With the consideration of their three‐dimensional structural parameters, three‐dimensional color prediction models, K/S‐, R‐, and L*a*b*‐based models, were developed through the optimization of previous two‐dimensional models which have been reported to be the three most accurate models for single‐layered woven structures. The accuracy of the new three‐dimensional models was evaluated by calculating the color differences ΔL*, ΔC*, Δh°, and ΔE_CMC(2:1) between the measured and the predicted colors of the samples, and then the error values were compared to those of the two‐dimensional models. As a result, there has been an overall improvement in color predictions of all models with a decrease in ΔE_CMC(2:1) from 10.30 to 5.25 units on average after the three‐dimensional modeling.     

Back-analysis of geotechnical parameters on PVD-improved ground in the Mekong Delta

This study presents a back-analysis of geotechnical parameters on prefabricated vertical drain improved ground at a site in the Mekong Delta. Various time?settlement behaviors that reflected different clay thicknesses and loading patterns were observed. The total surface settlement behavior at several monitoring locations was simulated using an updated exponential method that considered staged construction. The analyzed results were validated by substituting the values into a theoretical solution for radial consolidation. The estimated theoretical behaviors were comparable with the monitored behaviors. The geotechnical parameters were back-analyzed by applying the previously analyzed results to various theoretical and empirical formulas. However, the use of extensometer data that were installed at large intervals produced different values of the geotechnical properties. Furthermore, finite element analysis supported the back-analyzed total settlement behaviors and nearly disregarded the application of the geotechnical properties that were obtained using either surface or subsurface settlement data. However, settlements and excess pore pressures in the sublayers were not successfully predicted even when the geotechnical properties were adjusted. Thus, subsurface instruments that can be installed closely in thick clay deposits are required to reliably reevaluate the variations in geotechnical properties along a certain depth.     

Methyltransferase Contingencies in the Pathway of Everninomicin D Antibiotics and Analogues

Everninomicins are orthoester oligosaccharide antibiotics with potent activity against multidrug-resistant bacterial pathogens. Everninomicins act by disrupting ribosomal assembly in a distinct region in comparison to clinically prescribed drugs. We employed microporous intergeneric conjugation with Escherichia coli to manipulate Micromonospora for targeted gene-replacement studies of multiple putative methyltransferases across the octasaccharide scaffold of everninomicin effecting the A₁, C, F, and H rings. Analyses of gene-replacement and genetic complementation mutants established the mutability of the everninomicin scaffold through the generation of 12 previously unreported analogues and, together with previous results, permitted assignment of the ten methyltransferases required for everninomicin biosynthesis. The in vitro activity of A₁- and H-ring-modifying methyltransferases demonstrated the ability to catalyze late-stage modification of the scaffold on an A₁-ring phenol and H-ring C-4’ hydroxy moiety. Together these results establish the potential of the everninomicin scaffold for modification through mutagenesis and in vitro modification of advanced biosynthetic intermediates.     

Detailed study on fusion characteristics of rigid poly(vinyl chloride) nanocomposites: The comparison of using multiple regression analysis and artificial neural network

Fusion behavior of poly(vinyl chloride) (PVC) compounds plays an important role in the development of physical properties of processed material. The fusion characteristics in PVC processing are governed by material variables that affect the fusion with some interactions. In this research, the aim was to characterize the effects of formulation ingredients on fusion characteristics of PVC. Four material parameters, including the contents of nanoclay (NC), azodicarbonamide, calcium stearate, and processing aid, are proposed as affecting variables. The fusion time (FT) as well as fusion factor (FF) are considered fusion indicators and are experimentally determined in some different levels of affecting parameters. The multivariable regression analysis (MRA) and the Artificial Neural Network (ANN) modeling are considered as two analytical methods. The regression analysis result for the FT denotes, in part, significant linear and quadratic effects of NC and also its significant interactions with azodicarbonamide and calcium stearate, whereas that of FF indicates only a linear effect of NC. ANN modeling is performed with a three‐layer (input, hidden, and output) neural network. The results of the comparison of the MRA and ANN predictions with experimental values are reported as the correlation coefficient (R²), mean‐square error, and mean absolute percentage error for both FF and FT parameters. The obtained values clearly denote that the ANN results are more precise and especially more general than those of MRA. However, in the case of FT, improvement of the ANN modeling is much greater than that of FF. J. VINYL ADDIT. TECHNOL., 21:147–155, 2015. © 2014 Society of Plastics Engineers     

Supramolecular Assembly of Aminoethylene‐Lipopeptide PMO Conjugates into RNA Splice‐Switching Nanomicelles

Phosphorodiamidate morpholino oligomers (PMOs) are oligonucleotide analogs that can be used for therapeutic modulation of pre‐mRNA splicing. Similar to other classes of nucleic acid‐based therapeutics, PMOs require delivery systems for efficient transport to the intracellular target sites. Here, artificial peptides based on the oligo(ethylenamino) acid succinyl‐tetraethylenpentamine (Stp), hydrophobic modifications, and an azide group are presented, which are used for strain‐promoted azide‐alkyne cycloaddition conjugation with splice‐switching PMOs. By systematically varying the lead structure and formulation, it is determined that the type of contained fatty acid and supramolecular assembly have a critical impact on the delivery efficacy. A compound containing linolenic acid with three cis double bonds exhibits the highest splice‐switching activity and significantly increases functional protein expression in pLuc/705 reporter cells in vitro and after local administration in vivo. Structural and mechanistic studies reveal that the lipopeptide PMO conjugates form nanoparticles, which accelerate cellular uptake and that the content of unsaturated fatty acids enhances endosomal escape. In an in vitro Duchenne muscular dystrophy exon skipping model using H2K‐mdx52 dystrophic skeletal myotubes, the highly potent PMO conjugates mediate significant splice‐switching at very low nanomolar concentrations. The presented aminoethylene‐lipopeptides are thus a promising platform for the generation of PMO‐therapeutics with a favorable activity/toxicity profile.     

Combination of nuclear magnetic resonance spectroscopy and nonlinear methods to analyze the copolymerization of phosphonic acid derivatives

We demonstrate in this study that the combination of modern inline monitoring methods [here: inline nuclear magnetic resonance (NMR)] with simulations gains more exact and profound kinetic results than previously used methods like linearization without that combination. The ¹H-NMR spectroscopic data (more than 100 data points) are used to construct the copolymerization diagram. The reactivity ratios are obtained applying the van Herks nonlinear least square method. The examination of the radical copolymerization of 2-hydroxyethyl methacrylate (HEMA) with (2-{[2-(ethoxycarbonyl)prop-2-en-1-yl]oxy}ethyl) phosphonic acid (ECPPA) as important adhesive monomer used in dentistry yields reactivity ratios of r_HEMA = 1.83; r_ECPPA = 0.42. The copolymerization diagram reflects nonideal, non-azeotropic copolymerization. The sequence distribution of the obtained by Monte Carlo simulation indicates the generation of statistical copolymers. As an important finding, it is demonstrated that the repeating units responsible for etching and adhesion are arranged over the whole polymer chain, which is necessary to achieve proper functionality. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48256.     

Improved method for roadside barrier length of need modeling using real-world trajectories

The 2011 AASHTO Roadside Design Guide (RDG) contains perhaps the most widely used procedure for choosing an appropriate length of need (LON) for roadside barriers. However, this procedure has several limitations. The procedure uses a highly simplified model of vehicle departure, and the procedure does not allow designers to specify an explicit level of protection. A new procedure for choosing LON that addresses these limitations is presented in this paper. This new procedure is based on recent, real-world road departure trajectories and uses this departure data in a more realistic way. The new procedure also allows LON to be specified for a precisely known level of protection – a level which can be based on number of crashes, injury outcomes or even estimated crash cost – while still remaining straightforward and quick to use like the 2011 RDG procedure.