2,6-二乙酰基吡啶合成方法的改进

优化了2，6—二乙酰基吡啶的合成工艺。以2，6—吡啶二羧酸为原料，经过醇化及克莱森酯缩合反应，合成了2，6—二乙酰基吡啶，2，6—吡啶二羧酸二乙醇和2，6—二乙酰基吡啶的分离收率分别为94．1％和88．9％，2，6—二乙酰基毗啶的质量分数大于99％。     

氯化聚丙烯改性胶粘剂的合成及粘附性能研究

以甲苯为溶剂，过氧化二苯甲酰(BP0)为引发剂，通过自由基聚合，采用甲基丙烯酸羟乙酯(HEMA)和苯乙烯(St)接枝改性氯化聚丙烯(CPP)。研究了不同苯乙烯用量、不同反应温度、不同反应时间、不同引发剂用量对改性氯化聚丙烯胶粘剂粘附性能的影响，得出较佳的工艺条件为反应温度90℃，反应时问2h，原料配比m(CPP)：m(HEMA)：m(St)：m(BPO)=50：0．5：0．6：0．15。     

Low-Temperature Aging of t-ZrO2 Polycrystals with 3 mol% Y2O3

A kinetic study of the aging behavior of tetragonal zirconia polycrystals (TZPs) from 100° to 500°C suggests that there exists a cricital grain size of 0.52 μm below which the tetragonal symmetry can be retained. Property degradation of TZPs at low temperatures is connected with transformation-induced microcracking. It is reported here that the temperature range of 100° to 400°C in which degradation occurs could be explained by an infinite incubation time for the lower limit and by the martensite starting temperature for the upper limit.     

合成氢化松香乙酯的新工艺研究

以DRC为催化剂,在无溶剂条件下,通过氢化松香与乙醇的直接酯化反应合成氢化松香乙酯。探索了反应温度、催化剂用量、反应时间、物料配比等因素对反应酯化率的影响,确定最佳反应条件为:反应温度180℃,催化剂用量为原料氢化松香质量的6%,反应时间6h,醇与酸的摩尔比为3∶1。在最佳条件下酯化率达92.2%。还探讨了用阴离子交换树脂柱层析分离纯化氢化松香乙酯粗产物的方法。此外,利用红外光谱对氢化松香乙酯精制产物进行了表征;用GC-MS分别对氢化松香乙酯粗产物及其精制产物进行了定性和定量分析,比较了柱层析前后化学组成的变化。     

混合材对碱—碳酸盐反应的影响

利用快速测长法研究了混合材对碱—碳酸盐反应的影响。通过试验证明混合材能减缓碱—碳酸盐反应的速度,但不能有效地抑制碱—碳酸盐反应,并初步探讨了混合材不能有效地抑制碱—碳酸盐反应的机理。     

2,6-萘二甲酸二甲酯与一些二甲基萘所形成的激基复合物

2,6-萘二甲酸二甲酯与一些二甲基萘可以形成激基复合物。本文通过稳态和动态荧光光谱研究了这类激基复合物的形成与分子结构的关系。结果表明,尽管这些二甲基萘的电离能基本相同,但因取代基位置不同使分子中电荷分布不同,从而影响了激基复合物的形成能力。     

石油钻采机械用橡胶气囊的研制

橡胶气囊是石油钻采设备上常用的一种刹车装置。介绍了橡胶气囊的模具设计、铜气嘴的处理、排气槽的加工布置等整个研制过程。经试验，生产制作的橡胶气囊完全达到设计要求。     

Measurement of the rheological properties of polymer melts with annular rheometer

An annular die has been designed having a very thin gap distance between two coaxial cylinders. The die was then used to measure wall normal stresses along the longitudinal direction of polymer melts flowing through the thin annulus. The materials investigated were high-density polyethylene, low-density polyethylene, polypropylene, and polystyrene. Also investigated were blends of polystyrene and polypropylene, and blends of polystyrene and high-density polyethylene The measurements of wall normal stresses were used to determine the rheological properties of the melts, namely, the melt viscosity from the slope of axial wall normal stress profiles and the melt elasticity from exit pressures. The interpretation of the experimental data was made possible by the fact that the narrow-gap annular die can be considered as a substitute for a thin slit die. It has been found that the results obtained in the present study are consistent with those reported earlier by the author, who at that time used both capillary and slit dies.     

Rheological properties of mixtures of molten polymer and fluorocarbon blowing agent. I. Mixtures of low-density polyethylene and fluorocarbon blowing agent

The viscosities of mixtures of low-density polyethylene and fluorocarbon blowing agent were determined from the measurement of wall normal stress along the longitudinal axis of a capillary die. For the study, three different grades of commercial high-pressure low-density polyethylene were used, together with the following fluorocarbon blowing agents, dichlorodifluoromethane (FC-12), dichlorotetrafluoroethane (FC-114), and blends of FC-12 and FC-114. In the experiment, blowing agent concentration and melt temperature were varied for each combination of polymer and blowing agent employed. Analysis of the experimental data has led to a correlation between the viscosity reduction factor (VRF) and the blowing agent concentration, in which VRF is defined as the ratio of the viscosity of polymer-blowing agent mixture to that of the polymer alone. It was found that the correlation obtained is independent of shear rate and temperature and dependent upon only the type of fluorocarbon blowing agent. The practical significance of the correlation is discussed. We have shown that the entrance pressure drop obtained in the absence of phase separation in the entrance region may be used as a measure of the elastic properties of mixtures of fluorocarbon blowing agent and low-density polyethylene resin.     

Guerbet十四醇的合成与表征

以正庚醇为原料 ,通过Guerbet反应合成Guerbet十四醇 (2 戊基壬醇 ,C14 GA)。用IR、NMR和元素分析测定了C14 GA的结构 ,并研究了反应温度和用料比对其产率的影响。实验结果如下 :(1)在较优化的反应条件下 (正庚醇的总加入量为 1mol,在实验过程中 ,先加入 1/ 3mol庚醇和 1/ 4mol的KOH ,在 16 0℃下反应 2h ,然后再加入剩下的 2 / 3mol庚醇和 4g 5 %Pd -C催化剂 ,在 15 5℃下反应 6h)合成产物 ,其产率可达到 5 4 2 0 % ;(2 )所合成的产物与试图要得到的Guerbet十四醇 (2 戊基壬醇 ,C14 GA)含有相同的基团 (2×—CH3、10×—CH2 —、1×CH、1×—CH2 —O—和 1×—OH) ,而且 ,所合成的产物中 ,w (C) =79 0 6 % ,w (H ) =13 6 2 % ,与从Guerbet十四醇分子式计算的理论值w(C) =78 5 0 % ,w (H) =14 0 1%基本一致。可见所合成的产物正是Guerbet十四醇 (C14 GA)