Microstructure-related fracture toughness and fatigue crack growth behaviour in toughened, anhydride-cured epoxy resins

Fracture toughness and fatigue crack propagation (FCP) of plain and modified anhydride-cured epoxy resin (EP) were studied at ambient temperature. Liquid carboxyl-terminated acrylonitrile-butadiene (CTBN) and silicon (SI) rubber dispersions were used as tougheners for the EP. The morphology of the modified EP was characterized by dynamic mechanical analysis (DMA) and by scanning electron microscopy (SEM). The fracture toughness, K_c, of the compositions decreased with increasing deformation rate. K_c of the EP was slightly improved by CTBN addition and practically unaffected by incorporation of the SI dispersion when tests were performed at low cross-head speed, v. Both modifiers improved K_c at high v, and also the resistance to FCP, by shifting the curves to higher stress intensity factor ranges, ΔK, by comparison with the plain EP. It was established that both fracture and fatigue performance rely on the compliance, J_R, at the rubbery plateau, and thus on the apparent molecular mass between crosslinks, M_c. The failure mechanisms were less dependent upon the loading mode (fracture, fatigue), but differed basically for the various modifiers. Rubber-induced cavitation and shear yielding of the EP were dominant for CTBN, whereas crack bifurcation and branching controlled the cracking in SI-modified EP. The simultaneous use of both modifiers resulted in a synergistic effect for both the fracture toughness at high deformation rate and the FCP behavior.     

混合结构楼房爆破拆除倒塌范围的确定

通过对混合结构楼房爆破倾倒过程特点的分析,提出了楼房在倾倒过程中的运动计算模型,并应用体积平衡原理,得到这类楼房爆破爆堆参数计算公式,用该公式计算的结果与实例中爆堆实测数据相比较,相对误差不超过11%.     

Non-contact methods of measuring moisture concentration in external layers of building partitions II—Monitoring of the water vapour condensation on porous surfaces

This paper present the results of the investigation into a potential application of laser radiation for the detection of phase transition processes occurring on the surface layers of porous materials. An attempt was made to discuss in the approximation equations, the relationships between coefficients of the reflected light, the temperature and humidity of the surrounding environment. Laser light reflected from the porous surface carries information about the roughness of the structure. The presence of water microdrop on the surface of the porous material, as a result of condensation and thus a phase transition, leads to the phase displacement of individual rays, which is represented by different images. Therefore, a comprehensive analysis of the reflected light parameters allows a dynamic study of the phase transition phenomena without mechanical intervention.     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

An important factor affecting synergism on coprocessing of Taiheiyo coal with Athabasca oil sand bitumen

A series of mixtures of Japanese subbituminous Taiheiyo coal and Athabasca oil sand bitumen (AOB) with various coal concentrations (0–100 wt%) was coprocessed in a 70 ml autoclave at 420°C for 1 h in the presence of H₂ (50 kg/cm² at room temperature) and sulfided Ni---Mo/Al₂O₂ catalyst. The mixture containing 2 wt% coal produced the largest amount of hexane soluble fraction (HS) and the smallest amount of benzene insoluble fraction (BI). Thus, a synergistic liquid production occurred for this mixture with 2 wt% coal by suppressing the retrogressive reactions which proceeded for pure AOB. The HS obtained from mixtures with 2–30 wt% showed higher H/C ratios and lower heteroatom contents than those obtained from pure AOB and the mixtures with more than 30 wt% coal. The amounts of transferable hydrogen contained in the mixtures were estimated using anthracene as a hydrogen acceptor. The mixtures with 2–10 wt% coal contained higher amounts of donor hydrogen than pure AOB. The HS yield from the various mixtures was correlated with the amount of donor hydrogens contained in the mixtures, except for the mixture with 10 wt% coal. Thus, the important factor which results in synergism is suggested to be the amount of donor hydrogens contained in the feed mixtures.     

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO2 for no reduction by NH3

Deactivation of copper-ion-exchanged hydrogen-mordenite-type zeolite catalyst by SO₂ for NO reduction by NH₃ was examined in a fixed-bed flow reactor. The deactivation of the catalyst was strongly dependent on reaction temperature. At high reaction temperatures over 300°C, the catalyst did not lose its initial activity up to 50 h of operation, regardless of SO₂ feed concentration from 500 to 20,000 ppm. However, at low reaction temperatures near 250°C, apparent deactivation did occur. Changes in the physicochemical properties such as surface area and sulfur content of deactivated catalyst well correlated with catalyst activity, depending upon reaction temperatures. The deactivation was due to pore blocking and/or filling by deactivating agents, which plugged and/or filled the pores of catalyst. The deactivating agents deposited on the catalyst surface were presumed to be (NH₄)₂SO₄ and/or (NH₄)HSO₄ from the results of TGA and ion-chromatography measurement.     

Interfacial chemistry and adhesive durability

The improved understanding of adsorption chemistry which has arisen from the development of new surface analytical techniques during the last twenty years has had a major effect on the understanding of catalytic reaction mechanisms. However, there are many other areas of technology where Interfacial chemistry has a determining role but where the understanding is much less developed. In this paper examples are presented of the role of interfacial chemistry in adhesion. In particular, It Is shown that modification of a surface to the extent of just a few atomic layers in depth can have dramatic effects on the performance of adhesive bonds, particularly when exposed to hostile environmental conditions. These examples will be used to highlight a need for greater fundamental understanding of the interfacial chemistry of adhesion and also other technologies where interface effects are dominant.     

The effect of pack-aluminisation on the microstructure of MCrAlY and the performance of thermal barrier coatings

Plasma spraying and pack-aluminising processes were combined and applied to the nickel-base superalloy Mar-M247 to improve its cyclic oxidation resistance. The performance tests of duplex ZrO₂-8 wt.%Y₂O₃/MCrAlY thermal barrier coatings (TBCs) were conducted at 1050 °C, 1075 °C, 1100 °C, 1150 °C and 1200 °C. The results of the experiments in this study showed that TBC specimens with the aluminised MCrAlY bond coat exhibited higher cyclic lives (except for the Ni-22Cr-10Al-1Y bond coat), at all the temperatures tested, than specimens on which the bond coat was not aluminised. The microstructures of the Co-29Cr-6Al-1Y, Co-32Ni-21Cr-8Al-0.5Y and Ni-22Cr-10Al-1Y bond coats with or without aluminising treatment were examined in detail using a scanning electron microscope equipped with an electron probe microanalyzer.     

Energy dissipation via radiative recombination and vibronic relaxation in σ-delocalized silicon backbone network polymers

The nature of ultrafast energy dissipation in poly(n-hexylsilyne), a prototypical σ-delocalized alkysilicon network polymer, is explored. This disordered silicon backbone material exhibits strong near-UV to visible band-edge absorption and a high quantum yield of visible emission. The time evolution of the emission band is studied over four decades of time using time-resolved luminescence as a probe. The data indicate that while there is an ‘intrinsic’ Stokes shift after photoexcitation due to kinetic energy relaxation (<10ps), thermalization within a dense band of vibronic states via intramolecular phonon-assisted hopping on a nanosecond timescale is the dominant mechanism for excited-state decay. The data can be understood in terms of theoretical predictions for energy relaxation in disordered materials.