对空压机一级超压的分析

对5L-408型空压机一级超压找出了原因，并对超压的机理进行了分析。     

玻璃两面重叠手印拍摄机理

根据斯涅尔定律和菲涅尔公式阐述清水衬底法消除玻璃下界面手印或玻纹的影像，以及用偏振光，紫外线拍摄玻面痕迹的方法和机理。     

科技期刊编辑专业化和学者化是保证期刊学术质量的关键

一般科技期刊刊载的论文内容都具有很强的专业性,这就要求科技期刊编辑必须具有丰富的专业知识和较高的学术水平才能胜任编辑工作.从编辑过程的选题组稿、论文初审、选择审稿专家和编辑加工四个方面对此进行了阐述,指出了提高科技期刊编辑的相关专业知识和学术水平的措施.     

土壤因子对植物缺铁失绿的影响

本文主要从土壤 pH ,重碳酸盐 ,和氮素形态等几方面综述了各种土壤因子对土壤缺铁失绿的影响 ,并提出了进一步加强研究的方向     

Two-photon pumping of a random laser

Random lasing originates from pumping disordered materials by high-intensity and high-frequency light. The performance of random lasers is restricted due to the absorption of pumping light within the interfacial layer. The lifetime of optical modes there is short due to the emission of photons to the outside, and it is hard to pump them sufficiently for lasing. The opportunity to excite the modes far from the material surface using two-photon absorption is investigated within the diffusion model. The authors show that lasing requires lower pump power for the two-photon pumping mechanism under conditions of negligible absorption of the emitted light. Experimental implications and restrictions are discussed.     

NiTi形状记忆合金激光气体氮化层表面特征

为改善NiTi合金的表面性能，利用2kW连续波Nd：YAG对NiTi合金进行激光气体氮化处理。采用SEM、TEM、XRD、XPS和纳米压痕研究了氮化层的显微组织及表面特征．结果表明：激光气体氮化可以在NiTi合金表面制备连续、无裂纹、厚度为2μm的TiN表面层，该表面层中基本不合有Ni元素且具有很高的硬度，其纳米压痕硬度为29．28GPa．     

汽轮机轴承烧瓦与轴颈的渗巴氏合金现象

简述轴承工作性质，巴氏合金应用与相组成的基本情况。论述汽轮机转子在两个电厂长期运行后，由于轴颈发生的不正常摩擦损伤，在大修改造中由无损检查、机械加工揭示出轴颈存在严重的渗巴氏合金现象，低熔点金属Sn、Sb与Cu向转子材料晶界的深层渗入最终导致了3根大型在投转子的严重开裂与报废。图11表2     

Time-dependent deformation in an enhanced SiC/SiC composite

Time-dependent deformation in an enhanced SiC/SiC composite has been studied under constant load at high temperatures of 1200 °C, 1300 °C, and 1400 °C. Creep damage evolution was evaluated by a Young’s-modulus change of partial unloading and microscopic observation. The addition of the glassy phase in the matrix is very effective for protecting the composite from oxidation. The transient creep is dominant in creep life at all the temperatures. An empirical equation is proposed to describe creep behavior of the composite. It is found that creep activation energy increases with creep time at stresses lower than matrix cracking stress, but the activation energy remains constant at stresses higher than the matrix cracking stress. The creep strain rate of the composite is considered to be controlled by creep of fibers based on examining the time, strain, stress, and temperature dependencies of creep strain rates.     

SiCf/SiC陶瓷复合材料的研究进展

SiCf/SiC陶瓷复合材料具有良好的力学性能、高温抗氧化性和化学稳定性，是航空航天和原子能等领域理想的新一代高温结构材料。本文概述了增强体SiCt的发展状况及存在的问题，对SiCt/SiC材料的制备工艺、界面相的研究状态、材料的损伤破坏机理和目前的应用研究进展做了综述，并分析了SiCf/SiC陶瓷复合材料的研究重点和发展前景。     

Aroused problems in the deposition of diamond-like carbon films by using the liquid phase electrodeposition technique

Hydrogenated diamond-like carbon (DLC) films were prepared by using liquid phase electrodeposition technique. The effects of the applied potential and the carbon sources on the deposition process and film structures were studied. It has been found that the organic liquids with high dielectric constants, small viscosities and the methyl group bonding to the polar group are appropriate carbon sources. The increasing of potential improves the formation of sp³ carbon during the deposition process. In a high electric field, organic molecules are polarized and reacted on the surface of the electrode, turning out DLC and other products. It is believed that the reaction follows a polarization-reaction mechanism.