Enhanced space-time block coded systems by concatenating turbo product codes

The BER performance of a turbo product code (TPC) based space-time block coding (STBC) wireless system has been investigated. With the proposed system, both the good error correcting capability of TPC and the concurrent large diversity gain characteristic of STBC can be achieved. The BER upper bound has been derived taking BPSK modulation as an example. The simulation results show that the proposed system with the concatenated codes outperforms the one with only TPC or STBC and other reported schemes that concatenate STBC with convolutional Turbo codes or trellis codes.     

Radio-frequency transmission properties of carbon nanotubes in a field-effect transistor configuration

In this letter, the radio-frequency (RF) transmission properties of single-walled carbon nanotubes (CNTs) have been characterized up to the frequency of 12 GHz in a carbon nanotube field-effect transistor (CNFET) configuration using a two-port S-parameter method for the first time. The RF characteristics of the CNTs were measured from the drain to the source of the CNFET. A resistance, inductance, and capacitance model has been proposed, and the element values have been extracted. Without the effect of the parasitics, the RF signal transmission in the CNTs presents no degeneration even at 12 GHz. The capacitive contact between CNTs and metal electrodes is reported.     

Low-/spl kappa/ BCB passivation on AlGaN-GaN HEMT fabrication

Due to the stress-induced polarization effect on the GaN HEMTs, the surface passivation of the device is critical and is deserved to conduct a detailed study. It has been proven that the GaN HEMTs demonstrate nondispersive pulsed current-voltage (I-V) characteristics and better microwave power performances after passivating the Si/sub 3/N/sub 4/ film on the GaN surface. In this letter, we proposed to use the BCB material, a negative photoresist with a low-/spl kappa/ characteristic, as the surface passivation layer on GaN HEMTs fabrication. After comparing the dc I-V, pulsed I-V, RF small-signal, microwave power characteristics, and device reliability, this BCB-passivated GaN HEMT achieved better performance than the Si/sub 3/N/sub 4/ passivated device.     

Effect of microwave preheating on the bonding performance of flip chip on flex joint

A microwave (MW) preheating mechanism of anisotropic conductive adhesive film (ACF) has been introduced in order to reduce the bonding temperature for flip chip technology. Thermal curing of epoxy shows a very sluggish and non-uniform curing kinetics at the beginning of the curing reaction, but the rate increases with time and hence requires higher temperature. On the other hand MW radiation has the advantage of uniform heating rate during the cycle. In view of this, MW preheating (for 2/3 s) of ACF prior to final bonding has been applied to examine the electrical and mechanical performance of the bond. Low MW power has been used (80 and 240 W) to study the effect of the MW preheating. It has been found that 170 °C can be used for flip chip bonding instead of 180 °C (standard temperature for flip chip bonding) for MW preheating time and power used in this study. The contact resistance (0.015–0.025 Ω) is low in these samples where the standard resistance is 0.017 Ω (bonded at 180 °C without prior MW preheating). The shear forces at breakage were satisfactory (152–176 N) for the samples bonded at 170 °C with MW preheating, which is very close and even higher than the standard sample (173.3 N). For MW preheating time of 2 s, final bonding at 160 °C can also be used because of its low contact resistance (0.022–0.032 Ω), but the bond strength (137.3–145 N) is somewhat inferior to the standard one.     

The elastic analysis of a dent on pressurised pipe

The elastic analysis of a dent on a pressurised cylinder is investigated. The predetermined shapes of the dent are grouped into three categories according to the physical geometry of the dent width, namely the local dent, the short dent, and the long dent. The induced bending stresses associated with the dent are evaluated using Sanders's non-linear shell theory. The geometry of the dent is treated as an initial geometric imperfection and incorporated in the expressions of strain. The non-linear cylindrical shell equations thus obtained are linearised and then solved by a Fourier series expansion technique. Comparison of theoretical results with the finite element approach is made for a pipe of assumed dimensions and pressure. Good agreement of the results is observed. The analytical approach of this paper is suitable for pipe or cylinder with a dent depth of up to five times the wall thickness.     

Fast-polarization-hopping transmission diversity to mitigate prolonged deep fades in indoor wireless communications

Fast-polarization-hopping (FPH) transmission diversity is herein proposed to mitigate prolonged deep fades at the mobile receiver in, for example, the indoor propagation environment. Even if the individual multipaths are each sufficiently strong for detection, deep fades may occur due to the multipath signals' destructive summation at the receiver. The relative immobility of the transmitter, the propagation environment, and the receiver in the indoor environment means that a deep fade may last for a very long duration, dropping calls or severing links. By rapidly hopping the transmission polarization (say, alternating transmission between a vertically-polarized-dipole antenna and a horizontally-polarized-dipole antenna - or between two "X"-oriented dipoles), the effective propagation channel experiences consecutive polarization modes (each involving a different multipath summation), all within the duration allowed by the channel-coder's interleaving depth. This scheme is usable for either frequency-shift keying (with incoherent demodulation), or for channel-coded phase-shift keying (with differential coding, or with pilot-symbol phase synchronization). This scheme requires no change in the mobile receiver (which does not need to be dual polarized). The base station also needs no spatially separated antenna array, nor any other additional hardware, no mechanical movement of the transmitting antenna(s), and no sophisticated signal processing (such as channel estimation or closed-loop feedback) nor any additional software. The proposed scheme's cost - relative to using antenna arrays at the base station and/or the mobile - is a potentially doubling of the transmission bandwidth. The proposed scheme's potential is illustrated by limited computer simulations using CINDOOR, a polarization-sensitive indoor wireless-propagation ray-tracing simulation software package based on geometrical optics and the uniform theory of diffraction (GO/UTD).     

A new construction of 16-QAM Golay complementary sequences

We present a new construction of 16-QAM Golay sequences of length n = 2/sup m/. The number of constructed sequences is (14 + 12m)(m!/2)4/sup m+1/. When employed as a code in an orthogonal frequency-division multiplexing (OFDM) system; this set of sequences has a peak-to-mean envelope power ratio (PMEPR) of 3.6. By considering two specific subsets of these sequences, we obtain new codes with PMEPR bounds of 2.0 and 2.8 and respective code sizes of (2 + 2m)(m!/2)4/sup m+1/ and (4 + 4m)(m!/2)4/sup m+1/. These are larger than previously known codes for the same PMEPR bounds.     

Area-efficient CMOS charge pumps for LCD drivers

Area-efficient 4/spl times/ charge pumps based on the cross-coupled structure that uses the V/sub dd/-2V/sub dd/ outputs alternately to reduce the number of power devices and capacitors are presented. Compared with conventional designs, our best design can save two power transistors, one capacitor, and two level shift circuits. An integrated 4/spl times/ charge pump is then designed to deliver 100 /spl mu/A at 9 V using a 0.8-/spl mu/m AMS high-voltage CMOS process. The topology can be extended to 2n/spl times/ charge pumps, and a 6/spl times/ charge pump is also fabricated and tested to demonstrate the validity of the extension.     

Database to dynamically aid probe design for virus identification.

Viral infection poses a major problem for public health, horticulture, and animal husbandry, possibly causing severe health crises and economic losses. Viral infections can be identified by the specific detection of viral sequences in many ways. The microarray approach not only tolerates sequence variations of newly evolved virus strains, but can also simultaneously diagnose many viral sequences. Many chips have so far been designed for clinical use. Most are designed for special purposes, such as typing enterovirus infection, and compare fewer than 30 different viral sequences. None considers primer design, increasing the likelihood of cross hybridization to similar sequences from other viruses. To prevent this possibility, this work establishes a platform and database that provides users with specific probes of all known viral genome sequences to facilitate the design of diagnostic chips. This work develops a system for designing probes online. A user can select any number of different viruses and set the experimental conditions such as melting temperature and length of probe. The system then returns the optimal sequences from the database. We have also developed a heuristic algorithm to calculate the probe correctness and show the correctness of the algorithm. (The system that supports probe design for identifying viruses has been published on our web page http://bioinfo.csie.ncu.edu.tw/.)     

在双镶嵌铜互联中O.13微米器件生成用的基于PVD和ALD阻挡层的先进技术

1. Introduction The requirement of minimal bottom coverageand thick sidewall coverage for PVD-based films forlow via resistance and improved stress migration isnot easy to achieve with traditional depositionmethods. Modern I-PVD techniques give high bot-tom coverage, due to the ionized component of thedeposition flux. Sidewall coverage tends to be low,which is mainly due to off-normal deposition fluxand a less than unity sticking coefficient.