Acquisition and pattern recognition of spectrum information of welding metal transfer

With the creation of a pattern recognition system for metal transfer mode, this article has collected five kinds of spectrum signals in gas metal arc welding (MIG, MAG and CO₂) and take them as training samples. These samples have been pretreated by computer, several key characteristic parameters of the spectrum signal have been creatively extracted, and a corresponding recognition function and a minimum-distance-classifier have been constructed. The results show that the pattern recognition of several kinds of metal transfer modes for the metal gas arc welding can be done successfully, and relative important parameters in welding process, such as the frequency of droplet transfer and the approximate diameter of each droplet, can also be obtained.     

数值试井在白6-2井测试资料分析评价中的应用

数值试井是在近来发展的一项新的试井解释技术，具有处理非均质，复杂边界油气藏问题的优点，弥补了常规解析试井技术的不足。运用数值试井解释技术，结合动、静态资料，通过对白6-1断块白6-2井测试资料的综合分析评价，确定了储层渗流参数，落实了该气藏的边界情况，为该断块下一步开发提供可靠依据。     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

Analysis of the mechanism of die soldering in aluminum die casting

A mechanism of soldering of an aluminum alloy die casting to a steel die is proposed. A soldering critical temperature is postulated, at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. The liquid joins the die with the casting upon solidification. The critical temperature is determined by the elements in both the casting alloy and the die material and is equal to the solidus temperature of the resulting alloy. The critical temperature is used to predict the onset of die soldering, and the local liquid fraction is related to the soldering tendency. Experiments have been carried out to validate the concept and to determine the critical temperature for die soldering in an iron-aluminum system. Thermodynamic calculations are used to determine the critical temperature and soldering tendency for the cases of pure aluminum and a 380 alloy in a steel mold. Factors affecting the soldering tendency are discussed, and methods for reducing die soldering are suggested.     

用CMOS工艺实现VSR光电集成接收机的途径

介绍了10Gbit／s速率的甚短距离光传输系统VSR(Very Short Reach)中的接收机。分析了几种有希望用于VSR系统的CMOS工艺兼容的光电探测器。提出用CMOS电路实现VSR光电集成(OEIC)接收机的可能性和实现方法。     

Inhibition effect of carbon dioxide on the oxidation of hydrogen over a platinum foil catalyst

This paper investigates the catalytic ignition of the H₂/O₂/CO₂ mixture on platinum in a stagnation flow at atmospheric pressure experimentally and numerically. We measure the ignition temperatures of the gas mixtures flowing towards resistively heated platinum with various composition ratios and various diluent gases of N₂, Ar and CO₂. Compared with N₂ or Ar, the CO₂ dilution shows higher ignition temperature by about 50 K, even at the same composition ratio. The ignition temperature increase is proportional to the dilution ratio. Through the numerical simulation, it is illustrated that higher ignition temperature is caused by the adsorption of CO₂ and following dissociation on platinum surface, which was to date considered negligible in catalytic combustion.     

An adaptive p-persistent MAC scheme for multimedia WLAN

The letter proposes an adaptive p-persistent-based (APP) medium access control (MAC) scheme for the IEEE 802.11e distributed WLAN supporting multimedia services. The APP MAC scheme adaptively gives differentiated permission probabilities to transmission stations which are in different access category and with various waiting delay. Simulation results show that the APP MAC scheme can improve the performance of multimedia WLAN, such as small voice packet dropping probability, low delay variation, and high system throughput, compared to conventional MAC algorithms     

利用中石油域用户认证系统实现数据存储备份

系统面向中石油域用户提供了安全、高速的数据传输服务.实现了数据传输DES加密、用户登录LDAP限制、系统安全审计、空间容量扩容等功能.充分利用SAN网络光存储设备,同时也为油田网络存储应用的开发提供了成功经验.     

ESD protection design to overcome internal damage on interface circuits of a CMOS IC with multiple separated power pins

This paper reports a real case of electrostatic discharge (ESD) improvement on a complementary metal oxide semiconductor integrated circuit (IC) product with multiple separated power pins. After ESD stresses, the internal damage have been found to locate at the interface circuit connecting between different circuit blocks with different power supplies. Some ESD designs have been implemented to rescue this IC product to meet the required ESD specification. By adding only an extra ESD clamp N-channel metal oxide semiconductor with a channel width of 10 /spl mu/m between the interface node and the ground line, the human-body-model (HBM) ESD level of this IC product can be improved from the original 0.5 to 3 kV. By connecting the separated vertical sync signal (VSS) power lines through the ESD conduction circuit to a common VSS ESD bus realized by the seal ring, the HBM ESD level of the enhanced version IC product with 12 separated power supplies pairs can be significantly improved from original 1 kV up to > 5 kV, without the noise coupling issue.     

Using buried capacitor in LTCC-MLC balun

A novel chip-type ceramic balun designed in the 2.4 GHz ISM band frequency is presented. A buried capacitor is included in the balun, so that the length of the coupled transmission lines can be reduced and can be designed very easily. A meander or spiral broadside coupled-line is adopted to realise the proposed LTCC multi-layer balun. The measured performances of phase and amplitude balance for this LTCC-MLC balun show a good match with computer simulation