氧化铝厂渣浆泵机械密封的失效形式及改进措施

本文介绍了渣浆泵机械密封的失效形式,并根据长期现场工作经验,分析了机械密封泄漏的主要原因,据此提出了改进措施,通过对动静环密封面倒角,改变密封面尺寸及载荷系数后有效地解决了由于径向跳动过大而引起的密封面刮碰擦裂的失效问题。     

Formation and Characterization of 1.5-Monolayer Self-Assembled InAs/GaAs Quantum Dots Using Postgrowth Annealing

In this paper, we report that low-density InAs/GaAs quantum dots (QDs) can be formed by postgrowth annealing the samples with 1.5-monolayer (ML) InAs coverage, which is thinner than the critical layer thickness for the Stranski-Krastanov growth. The annealing procedure was performed immediately after the deposition of the InAs layer. The effects of annealing time and annealing temperature on the dot density, dot size, and optical characteristics of the QDs were investigated. The optimum annealing conditions to obtain low-density QDs are longer than 60 s and higher than 500degC . Meanwhile, no luminescence can be observed for the wetting-layer, which may suggest that the postgrowth annealing will make the wetting layer thinner and thus reduce the effects of wetting layer on carrier relaxation and recombination. On the other hand, we observe that a decrease of the PL intensity at the annealing conditions of 60 s and 515degC , which is possibly due to the increasing surface dislocations resulted from the In adatom desorption at higher annealing temperature.     

对企业账面利润与现金流量关系的认识

本文阐述了企业账面利润与现金流量的关系 ,指出了企业账面利润与现金流量的四个不同点 ,并且提出了一个现代企业应如何在四个方面做好工作 ,正确处理好这两者的关系。     

Rolling and Lifting Probabilities for Sediment Entrainment

This study addresses the rolling and lifting probabilities for sediment entrainment by incorporating the probabilistic features of the turbulent fluctuation and bed grain geometry. The lognormally distributed instantaneous velocity and uniformly distributed initial grain position, along with a relation between lift coefficient and particle Reynolds number, are used to extend the theoretical formulation of the entrainment probabilities in smooth-bed flows. The two threshold conditions identified herein enable us to precisely define the probabilities of entrainment in the rolling and lifting modes. The results obtained in this study coincide well with the published data. The lifting probability increases monotonously with the dimensionless shear stress θ, which is consistent with the earlier results yet displays improved agreement with the experimental data. The maximum value of rolling probability, with a magnitude of 0.25, occurs at θ ≈ 0.15. For θ<0.05 (or θ>0.6), the rolling (or lifting) probability makes up more than 90% of the total entrainment probability and thus can be used as an approximation to the total probability of entrainment. The proposed rolling and lifting probabilities are further linked to the two separate criteria for incipient motion to explore the critical entrainment probabilities. The results reveal that a consistent probability corresponding to the critical state of sediment entrainment cannot be found.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry     

Conformational effects in the reversed-phase chromatographic behavior of recombinant human growth hormone (rhGH) and N-methionyl recombinant human growth hormone (Met-hGH).

This paper examines the retention behavior of recombinant DNA-derived human growth hormone (rhGH) in reversed-phase chromatography and its separation from the closely related N-methionyl variant (Met-hGH). It is first shown that retention for rhGH decreases with increasing column temperature when 1-propanol (1-PrOH) is used as organic modifier. On the other hand, retention increases with temperature when acetonitrile (CH3CN) is employed. The differences in behavior for the two organic modifiers could be related to conformational changes in the protein as determined by solution and adsorption intrinsic fluorescence spectroscopy. Specifically, desorption and elution of rhGH using 1-PrOH could be correlated with a solvent-induced conformational change, with retention decreasing with increasing temperature due to the increasing ease of structural alteration. On the other hand for CH3CN the increase in retention correlated with temperature rise was related to a partial structural change yielding a more hydrophobic species. In this case, a surface-driven process is suggested. The work then turned to the separation of rhGH and Met-hGH where it was found for both organic modifiers optimum separation occurred at 45 degrees C and pH 6.5. Separate studies revealed that during the conformational change Met-hGH appeared more hydrophobic than rhGH since protein-protein aggregation was observed at a lower 1-PrOH concentration. It is suggested that this hydrophobic difference, which was optimized under the conditions cited above, resulted in the separation. The study demonstrates the importance of conformational changes in retention behavior and separation of protein samples.     

Uncertainty analysis and allocation of joint tolerances in robot manipulators based on interval analysis

Many uncertain factors influence the accuracy and repeatability of robots. These factors include manufacturing and assembly tolerances and deviations in actuators and controllers. The effects of these uncertain factors must be carefully analyzed to obtain a clear insight into the manipulator performance. In order to ensure the position and orientation accuracy of a robot end effector as well as to reduce the manufacturing cost of the robot, it is necessary to quantify the influence of the uncertain factors and optimally allocate the tolerances. This involves a study of the direct and inverse kinematics of robot end effectors in the presence of uncertain factors. This paper focuses on the optimal allocation of joint tolerances with consideration of the positional and directional errors of the robot end effector and the manufacturing cost. The interval analysis is used for predicting errors in the performance of robot manipulators. The Stanford manipulator is considered for illustration. The unknown joint variables are modeled as interval parameters due to the inherent uncertainty. The cost-tolerance model is assumed to be of an exponential form during optimization. The effects of the upper bounds on the minimum cost and relative deviations of the directional and positional errors of the end effector are also studied.     

Preparation and gas-sensing characteristics of nanocrystalline spinel zinc ferrite thin films

Zinc ferrite is a promising sensor material. In this paper, thin films of nanocrystalline zinc ferrite were deposited on alumina substrates by nebulization of a 0.01-M solution of a mixture of ZnCl/sub 2/ and FeCl/sub 3/ in ethanol (Zn:Fe=1:2) followed by pyrolysis and annealing in flowing air. The resulting films were characterized by X-ray diffraction and scanning electron microscopy, and the gas-sensing properties of as-deposited films were also investigated.