Highly compact AC-AC converter achieving a high voltage transferratio

This paper reports a new, highly integrated modular design approach for pulsewidth-modulation AC-AC converters based on a modular phase-bank structure. Novel high-power 3-in-1 integrated bi-directional power modules (IBPM) rated at 1200-V AC and 150 A and the 3-to-1 phase bank circuits have been successfully developed, fabricated and tested. This enables the modularity design of the multiphase converter systems and reduces the critical parasitic inductance. A theoretical analysis of the IBPM's silicon utilization for this new breed of direct power converters has been outlined. A lab prototype at medium power level has been successfully designed, implemented, and tested with good results. A nearly 460-VRMS out voltage at a 1:0.955 voltage transfer ratio, which, perhaps, is the highest performance reported so far in the literature, has been achieved by the novel two-side modulation control system. The converter-fed AC motor system is able to operate over the 0-240 Hz range with inherent regenerative capability and four-quadrant operation. Potential industrial applications are also briefly highlighted in this paper     

Design aspects of planar and conventional SMPS transformer: a cost benefit analysis

The intent of this paper is to design a high-frequency transformer that is to be incorporated into the DC/DC pulsewidth-modulated switch-mode power supplies by two different technical approaches: a conventional wound-coil magnetic using copper wires, and a planar magnetic with layered copper tracks on laminated printed circuit board. Comparisons will be made between the two approaches in terms of profile: mounting height and surface area, and performance: power losses and efficiency. Other indicators like temperature rise and leakage inductance that causes electromagnetic interference, and cost, materials, and process fluency are also to be looked into. A sandwiched configuration for primary and secondary windings is proposed for the planar type. Issues arising and typical phenomena encountered will be discussed in detail. Primarily, the dominating factor in performance, cost effectiveness, or circuit compactness that restrains the choice of a particular type is to be evaluated.     

含氟聚酰亚胺的辐射交联及其交联度的XPS表征

含氟聚酰亚胺(FPI)是一种耐高温、耐水解的新型聚酰亚胺。到目前为止,尚未见文献报道它的辐射交联。本文发现它能在高温辐射下交联,交联后的含氟聚酰亚胺的玻璃化转变温度以及高温力学性能有明显提高。本文还首次用XPS方法做了它的交联度表征。用XPS方法求得FPI的凝胶化剂量为50Mrad。     

石油系油浆与煤系闪蒸油的焦化性能——I．热解条件的影响

通过偏光显微镜观察了石油系油浆（LH）与煤系闪蒸油（SN）焦化后所得焦块的光学结构。结果表明，在较宽条件下两种原料单独焦化均得不到取向度高的流线型结构。将两种原料以一定比例混合后先热解丙焦化所得焦块的光学结构明显好于二者混合后直接焦化所得焦块的光学结构，其中LH和SN以3：2的重量比混合后在440℃、1MPa下热解3．5h然后再在530℃、1MPa下焦化8h所得焦块为具有较高取向度的流线型结构，适合于作为针状焦的起始原料。     

一机多控视频点播系统

介绍一种自行设计、开发的一机多控视频点播系统，讲述了系统组成及设计方案，它具有服务功能多，操作方便、性能价格比高等特点。     

A Petri net based approach to modeling and scheduling for an FMSand a case study

In this paper, a timed-place Petri net (TPPN) model for flexible manufacturing systems (FMSs) is constructed, which contains two major submodels: the stationary transportation model; and the variable process flow model. For multiple automated guided vehicle (AGV) systems, the authors embed a simple rule and introduce a push-AGV strategy in a TPPN model to solve the collision and traffic jam problems of such vehicles. Since a firing sequence of the TPPN from the initial marking to the final marking can be seen as a schedule of the modeled FMS, by using an A^* based search algorithm, namely, the limited-expansion A algorithm, an effective schedule of the part processing can be obtained. To show the promising potential of the proposed work, a prototype FMS is used as a target system for implementation. The experiment results assert that the job-shop scheduling problem can always be satisfactorily solved     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

Using thermally stimulated currents to find defective capacitors

BaTiO₃ multilayer capacitors with a nominal capacitance of 3.5nF have been carefully measured using the thermally stimulated current (TSC) technique. When a 300V polarization voltage is applied at room temperature, a new TSC peak appeared in defective sample A after it has been immersed in water. No new peak was found in good-quality sample B after a similar treatment. The accelerated life test shows that sample A hasa much shorter life than sample B in terms of insulation resistance.     

山洪灾害预警准确度与及时度研究

山洪灾害预警准确度与及时度是一对相互矛盾而又联系的重要指标。文章通过对这两项指标的研究和对引发灾害的降雨强度、降雨以及灾害发生的时间资料进行分析,从而获取预警系统建设的基本技术要点和参数,对把握山洪灾害预警系统的设计定位、启用时机和作用评估具有重要作用和意义。     

Friction and wear of Inconel 690 and Inconel 600 for steam generator tube in room temperature water

In the steam generators of nuclear power plants, the flow of cooling water can cause the tubes to vibrate, resulting in fretting wear damage due to contacts between these tubes and their supports. The tubes are made of Inconel 690 and Inconel 600 and the supports are made of STS 304. In this paper, fretting wear tests in water were performed using the materials Inconel 690 and Inconel 600 in contact with STS 304. Fretting tests using a cross-cylinder type set up were conducted under various vibrating amplitudes and applied normal loads in order to measure friction forces and wear volumes. Also, conventional sliding tests using a pin-on-disk type set up were carried out to compare these test results.In the fretting tests, friction force was found to be strongly dependent on normal load and vibrating amplitude. Coefficients of friction decreased with an increase in the normal load and a decrease in the vibrating amplitude applied. Also, the wear of Inconel 600 and Inconel 690 was predicted using a work rate model. Depending on the normal load and vibrating amplitude applied, distinctively different wear mechanisms and often drastically different wear rates occurred. It was found that the fretting wear coefficients for Inconel 600 and Inconel 690 were 9.3×10⁻¹⁵ and 16.2×10⁻¹⁵ Pa⁻¹, respectively. This study shows that Inconel 690 can result in lesser friction forces and exhibits less wear resistance than Inconel 600 in room temperature water.