Modification of ASM3 for the determination of biomass adsorption/storage capacity in bulking sludge control.

The selector activated sludge (SAS) systems are known to prevent excessive growth of filamentous microorganisms responsible for bulking sludge, but these systems were hardly ever modelled. This study aimed to develop a model capable of predicting rapid substrate removal in the SAS systems. For this purpose, the Activated Sludge Model No. 3 (ASM3) was extended with three processes (adsorption, direct growth on the adsorbed substrate under aerobic or anoxic conditions). The modified ASM3 was tested against the results of batch experiments with the biomass originating from two full-scale SAS systems in Germany. The endogenous biomass was mixed with various readily biodegradable substrates (acetate, peptone, glucose and wastewater) and the utilisation of substrate (expresses as COD) and oxygen uptake rates (OURs) were measured during the experiments. In general, model predictions fitted to the experimental data, but a considerable number of kinetic (5) and stoichiometric (2) parameters needed to be adjusted during model calibration. The simulation results revealed that storage was generally a dominating process compared to direct growth in terms of the adsorbed substrate utilisation. The contribution of storage ranged from 65-71% (Plant A) and 69-92% (Plant B).     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.     

Evanescently coupled photodiodes integrating a double-stage taper for 40-Gb/s applications-compared performance with side-illuminated photodiodes

The design, fabrication, and performance of double-stage taper photodiodes (DSTPs) are reported. The objective of this work is to develop devices compatible with 40-Gb/s applications. Such devices require high efficiency, ultrawide band, high optical power handling capability, and compatibility with low-cost module fabrication. The integration of mode size converters improves both the coupling efficiency and the responsivity with a large fiber mode diameter. Responsivity of 0.6 A/W and 0.45 A/W are achieved with a 6-/spl mu/m fiber mode diameter and cleaved fiber, respectively, providing relaxed alignment tolerances (/spl plusmn/1.6 /spl mu/m and /spl plusmn/2 /spl mu/m, respectively), compatible with cost-effective packaging techniques. DSTPs also offer a wide bandwidth greater than 40 GHz and transverse-electric/transverse-magnetic polarization dependence lower than 0.2 dB. Furthermore, a DSTP saturation current as high as 11 mA results in optical power handling greater than +10 dBm and a high output voltage of 0.8 V. These capabilities allow the photodiode to drive the decision circuit without the need of a broad-band electrical amplifier. The DSTP devices presented here demonstrate higher responsivities with large fiber mode diameter and better optical power handling capabilities and are compared with classical side-illuminated photodiodes.     

LiNbO3 optical waveguides formed in a new proton source

Proton-exchanged planar waveguides have been fabricated on Z-cut and X-cut lithium niobate crystals by using a new proton source formed by a mixture of benzoic and adipic acids. Waveguide index profiles and optical characteristics have been obtained at different values of the adipic-benzoic acid concentration ratio. The samples have been structurally characterized by Raman and infrared (IR) absorption spectroscopy and double-crystal X-ray diffraction. Good quality samples have been fabricated by using 30 mol% ratio dilution, showing very low scattering levels (<0.1 dB/cm), relatively high electrooptic coefficient (r₃₃=0.88 pm/V), and low relative percentage of interstitial protons (26%). The main factor limiting the waveguide optical properties is the substitutional-interstitial proton ratio, which can be easily controlled to produce good quality waveguides. A demonstration of the repeatability of the exchange process in the acid mixture is also provided     

A base-band NDS electrode configuration for HACT devices

Heterostructure Acoustic Charge Transport (HACT) devices have been fabricated with a new nondestructive sense (NDS) electrode structure that provides for the recovery of base-band signals without the use of an integrating capacitor. This electrode structure provides an output signal comprising an RF carrier at the SAW frequency, amplitude modulated by the sampled input signal which has been delayed by a period proportional to the output electrodes distance from the input diode. The output of the NDS electrode structure is subsequently demodulated to provide the base-band signal     

Increasing the service properties of weld joints by electrohydroimpulse treatment

Known examples of the positive influence of electrohydroimpulse treatment on the quality of weld joints of various steels, particularly including an increase in their long-term and cyclic strength and also corrosion resistance, are analyzed. It is shown that in this case there is a reduction in residual macro- and micro-stresses and also a change in the parameters of the dislocation structure of the joint metal in the direction of stabilization of it.Translated from Problemy Prochnosti, No. 4, pp. 119–123, April, 1996.     

Shear horizontal wave propagation in periodically layeredcomposites

The transverse resonance approach to guided wave analysis is applied to shear horizontal (SH) wave propagation in periodically layered composites. It is found for SH waves that at high values of the guided wavevector β, the wave energy is trapped in the slower of the two media and propagates accordingly at the slower wavespeed. At low values of β, however, the modes demonstrate a clustering behavior, indicative of the underlying Floquet wave structure. The number of modes in a cluster is observed to correlate with the number of unit cells in the layered plate. New physical insights into the behavior of these systems are obtained by analyzing the partial waves of the guided SH modes in terms of Floquet waves. We show that the fast and slow shear waves in the periodically layered composite play an analogous role to the longitudinal and shear partial waves comprising Lamb waves in a homogeneous plate