Development of a simple microsystems membrane probe card

Presented here are details of the development of a novel membrane integrated circuit (IC) probe card structure based on microsystems technology. The device design allows probing of both solder bumps and pads. A self-limiting sensor was integrated to prolong device lifetime. Comparison with and discussion of the use of modelling is made. Possible enhancements to the probing structure are discussed to improve alignment and measurements. Also shown is data using our microsystems probe card to access a simple IC device. Our device has a contact resistance of less than 0.5 Ω for a force of 0.004 N. A method to implement our probing structure for commercial application and the potential developments which can be made to improve its ease of use are then discussed.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

Performance study of iSCSI-based storage subsystems

iISCSI is emerging as an end-to-end protocol for transporting storage I/O block data over IP networks. By exploiting the ubiquitous Internet infrastructure, iSCSI greatly facilitates remote storage, remote backup, and data mirroring. This article evaluates the performance of two typical iSCSI storage subsystems by measuring and analyzing block-level I/O access performance and file-level access performance. In the file-level performance study, we compare file access performance in an NAS scheme with that in an iSCSI-based SAN scheme. Our test results show that Gigabit Ethernet-based iSCSI can reach very high bandwidth, close to that of a direct FC disk access in block I/O access. However, when the iSCSI traverses through longer distance, throughput relies heavily on the available bandwidth between the initiator and the target. On the other hand, the file-level performance shows that iSCSI-based file access (SAN scheme) provides higher performance than using NFS protocol in Linux and SMB protocol in Windows (NAS scheme). However, the advantage of using iSCSI-based file accesses decreases as the file size increases. The obtained experimental results shed some light on the performance of applications based on iSCSI storage.     

Structure and electrical characteristics of Ce4+-doped Ba2In2O5

The In-site of Ba₂In₂O₅ with Brownmillerite structure was partially substituted for Ce⁴⁺ ions in order to examine the doping effect on the order-disorder transition. Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1, 0.2, 0.3, 0.5, 1.0, and 1.5) were prepared by solid state reaction. X-Ray diffraction analyses of these powder samples demonstrated that Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1 and 0.2) possesses Brownmillerite structure. With increasing content of Ce⁴⁺ ion the crystal system of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.3, 0.5, and 1.0) changed to cubic perovskite structure above the order-disorder transition temperature of Ba₂In₂O₅. Arrhenius plots of the electrical conductivities of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.2, 0.3, and 1.0) exhibited no discontinuity. These compounds had high transference numbers of oxide ion above 973 k.     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.     

Java multimedia telecollaboration

Using Java-based tools in multimedia collaborative environments accessed over the Internet can increase an application's client base. Most operating systems support Java, and its "compile once-run everywhere" architecture is easy to maintain and update. The Java-based tools presented here let users share Internet resources, including resources originally designed for single use.     

Metalorganic chemical vapor deposition of silver thin films for future interconnects by direct liquid injection system

Deposition of Ag films by direct liquid injection-metal organic chemical vapor deposition (DLI-MOCVD) was chosen because this preparation method allows precise control of precursor flow and prevents early decomposition of the precursor as compared to the bubbler-delivery. Silver(I)-2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octanedionato-triethylphosphine [Ag(fod)(PEt₃)] as the precursor for Ag CVD was studied, which is liquid at 30 °C. Ag films were grown on different substrates of SiO₂/Si and TiN/Si. Argon and nitrogen/hydrogen carrier gas was used in a cold wall reactor at a pressure of 50–500 Pa with deposition temperature ranging between 220 °C and 350 °C. Ag films deposited on a TiN/Si diffusion barrier layer have favorable properties over films deposited on SiO₂/Si substrate. At lower temperature (220 °C), film growth is essentially reaction-limited on SiO₂ substrate. Significant dependence of the surface morphology on the deposition conditions exists in our experiments. According to XPS analysis pure Ag films are deposited by DLI-MOCVD at 250 °C by using argon as carrier gas.     

The anisotropic effect of a weak magnetic field on the photoconductivity of C<Subscript>60</Subscript> single crystals

The effect of crystal orientation on the photogeneration of free charge carriers was studied for C₆₀ single crystals in a weak magnetic field. The photoconductivity sharply depends on the orientation of magnetic field with respect to the crystallographic directions, showing a 5–8% increase for seven axes of the C₆₀ crystal.     

Popular biorthogonal wavelet filters via a lifting scheme and its application in image compression

A technique using a lifting scheme is presented for constructing compactly supported wavelets whose coefficients are composed of free variables locating in an interval. An efficient approach-based wavelet for image compression is developed by selecting the coefficients of the 9-7 wavelet filter and associated lifting scheme. Furthermore, the rationalised coefficients wavelet filter that can be implemented with simple integer arithmetic is achieved and its characteristic is close to the well known original irrational coefficients 9-7 wavelet filters developed by A. Cohen et al. (Commun. Pure Appl. Maths., vol.45, no.1, p.485-560, 1992). To reduce the computational cost of image coding applications further, an acceleration technique is proposed for the lifting steps. Software and hardware simulations show that the new method has very low complexity, and simultaneously preserves the high quality of the compressed image.