Authentication by correspondence

Correspondence properties capture authentication only indirectly. We trace the origin of correspondence in the analysis of authentication protocols and investigate to what extent correspondence actually corresponds to the various flavors of authentication.     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

High-performance surface-micromachined inchworm actuator

This work demonstrates a polycrystalline silicon surface-micromachined inchworm actuator that exhibits high-performance characteristics such as large force (/spl plusmn/0.5 millinewtons), large velocity range (0 to /spl plusmn/4.4 mm/sec), large displacement range (/spl plusmn/100 microns), small step size (/spl plusmn/10, /spl plusmn/40 or /spl plusmn/100 nanometers), low power consumption (nanojoules per cycle), continuous bidirectional operation and relatively small area (600 /spl times/ 200/spl mu/m/sup 2/). An in situ load spring calibrated on a logarithmic scale from micronewtons to millinewtons, optical microscopy and Michelson interferometry are used to characterize its performance. The actuator consists of a force-amplifying plate that spans two voltage-controlled clamps, and walking is achieved by appropriately sequencing signals to these three components. In the clamps, normal force is borne by equipotential rubbing counterfaces, enabling friction to be measured against load. Using different monolayer coatings, we show that the static coefficient of friction can be changed from 0.14 to 1.04, and that it is load-independent over a broad range. We further find that the static coefficient of friction does not accurately predict the force generated by the actuator and attribute this to nanometer-scale presliding tangential deflections.     

Automation model of sewerage rehabilitation planning.

The major steps of sewerage rehabilitation include inspection of sewerage, assessment of structural conditions, computation of structural condition grades, and determination of rehabilitation methods and materials. Conventionally, sewerage rehabilitation planning relies on experts with professional background that is tedious and time-consuming. This paper proposes an automation model of planning optimal sewerage rehabilitation strategies for the sewer system by integrating image process, clustering technology, optimization, and visualization display. Firstly, image processing techniques, such as wavelet transformation and co-occurrence features extraction, were employed to extract various characteristics of structural failures from CCTV inspection images. Secondly, a classification neural network was established to automatically interpret the structural conditions by comparing the extracted features with the typical failures in a databank. Then, to achieve optimal rehabilitation efficiency, a genetic algorithm was used to determine appropriate rehabilitation methods and substitution materials for the pipe sections with a risk of mal-function and even collapse. Finally, the result from the automation model can be visualized in a geographic information system in which essential information of the sewer system and sewerage rehabilitation plans are graphically displayed. For demonstration, the automation model of optimal sewerage rehabilitation planning was applied to a sewer system in east Taichung, Chinese Taiwan.     

Evaluating the stabilisation degree of digested sewage sludge: investigations at four municipal wastewater treatment plants.

Further reduction of volatile suspended solids (VSS) during a post-stabilisation step was applied to evaluate the stabilisation degree of digested sewage sludge. For this purpose digested sludge was collected at four municipal wastewater treatment plants (WWTPs) and further stabilised in lab-scale chemostat reactors either under anaerobic or aerobic conditions. Experimental results showed that even in adequately digested sludge a consistent amount of VSS was degraded during aerobic post-stabilisation. It seems that aerobic conditions play a significant role during degradation of residual VSS. Additionally, specific VSS production (gVSS/peCOD110.d) as well as specific oxygen uptake rate were shown to be suitable parameters to assess the degree of sludge stabilisation at WWTPs. Fourier transform infrared spectroscopy was used to reveal changes in the sludge composition. Spectra of treated and untreated sludge samples indicated that the major component of residual VSS in stabilised sludge for instance consisted of biomass, while cellulose was absent.     

Manipulation of microenvironment with a built-in electrochemical actuator in proximity of a dissolved oxygen microsensor

Biochemical sensors for continuous monitoring require dependable periodic self diagnosis with acceptable simplicity to check its functionality during operation. An in-situ self-diagnostic technique for a dissolved oxygen microsensor is proposed in an effort to devise an intelligent microsensor system with an integrated electrochemical actuation electrode. With a built-in platinum microelectrode that surrounds the microsensor, two kinds of microenvironments, called the oxygen-saturated or oxygen-depleted phases, can be created by water electrolysis, depending on the polarity. The functionality of the microsensor can be checked during these microenvironment phases. The polarographic oxygen microsensor is fabricated on a flexible polyimide substrate (Kapton) and the feasibility of the proposed concept is demonstrated in a physiological solution. The sensor responds properly during the oxygen-generating and oxygen-depleting phases. The use of these microenvironments for in-situ self-calibration is discussed to achieve functional integration, as well as structural integration, of the microsensor system.     

Photoswitching of Ferroelectric Liquid Crystals Using Unsymmetrical Chiral Thioindigo Dopants: Photoinduced Inversion of the Sign of Spontaneous Polarization

A new unsymmetrical chiral thioindigo dopant 6‐[(R,R)‐2,3‐difluorooct‐1‐yloxy]‐5′‐nitro‐6′‐[(R)‐2‐octyloxy]thioindigo ( 4 ) designed to photoinvert the sign of spontaneous polarization (P_S) in a ferroelectric chiral smectic C (SmC*) liquid crystal was prepared using a synthetic approach previously developed in our laboratory. In this new “ambidextrous” design, the (R)‐2‐octyloxy side‐chain is sterically coupled to the thioindigo core and induces a positive P_S, whereas the (R,R)‐2,3‐difluorooctyloxy side‐chain is decoupled from the core and induces a larger negative P_S. In the trans form, this dopant induces a negative polarization in the SmC host (+)‐4‐(4‐methylhexyloxy)phenyl 4‐decyloxybenzoate ( PhB ). Irradiation of a 1 mol‐% mixture of 4 in PhB at λ = 510 nm caused a sign inversion of P_S, from –0.88 to +0.42 nC cm^–2 at T – T_C = –5 °C, which is consistent with an increase in the polarization power of the coupled 2‐octyloxy/thioindigo unit over that of the 2,3‐difluorooctyloxy unit, due to the increase in transverse dipole moment of the thioindigo core upon trans–cis photoisomerization. The P_S sign inversion was confirmed by a surface‐stabilized ferroelectric liquid crystal photoswitching experiment. Spectroscopic measurements on films of the doped liquid crystal mixtures showed that trans–cis photoisomerization is gradually suppressed with increasing dopant mole fraction, possibly as a result of increased dopant aggregation.     

Modeling Temperature in Coupled Electrical and Thermal Simulations of the Electroconsolidation® Process

Electroconsolidation® is a process for densifying complex-shaped parts by using electrically conductive particulate solids as a pressure-transmitting medium. The part is immersed in a bed of the particulate medium contained in a die chamber. Sintering temperature is achieved by resistive heating of the medium while applying compaction pressure. The process is capable of ultrahigh temperatures and short cycle times and offers the potential for low processing costs.

Control of the process and selection of process conditions require knowledge of the temperatures within the die. Temperature gradients exist because of the high heating rate and because of variations of density and electrical resistivity of the medium due to the presence of the part. Direct measurement of temperature with thermocouples or other conventional means is impractical because of the high temperatures, high currents, and high pressures that are involved. Therefore, a computer model was developed to predict temperature as a function of time and applied voltage for any location in the die. The computer model is composed of three parts: a geometrical model to approximate the density and resistivity variations in the medium, a finite-element model to calculate the rate of resistive heating within each element, and a finite-difference model to calculate the temperature distribution based on solution of the heat-transfer equations. Predicted temperatures have been shown to be in excellent agreement with measurements, and numerical simulation provided encouraging consistency and reasonably accurate predictions of temperature profiles within the die. The model demonstrated the feasibility of a new process to achieve simultaneous application of pressure and heat to powder densification in Electroconsolidation.     

A simple fiber-optic vehicle axle detector for roadways

This paper presents a fiber-optic vehicle axle detector for roadways. It is based on a fiber-optic Michelson interferometer that is mounted directly into the road surface. The fully dielectric design allows for remote operation of the sensor via a long section of optical fiber. A simple signal-processing scheme of the output signals has been adopted that allows for reliable detection of commercial and personal vehicles.