The relationship between preparation convergence and retention of extracoronal retainers

PURPOSE: Although traditional ideal convergence (the sum of taper of the opposite sides) for crown preparation has been arbitrarily set at 4 degrees to 10 degrees, some believe absolute parallelism yields the highest retention. This study examined the relationship between the degree of convergence of a machined metal die and the retention of its casting. MATERIALS AND METHODS: The method used was that of cementing cast metal crowns onto full crown preparations on brass dies with varying convergence angles, and then recording the force required to remove the crowns from the dies in a vertical direction using a Tate-Emery Testing Machine and Load Indicator. RESULTS: It was found that retention (i.e., the force needed to remove the cemented castings from the die in their common long axis) increases from 0 degree convergence to peak between 6 degrees to 12 degrees convergence. It also seems that a critical film thickness does exist for optimum retention, and that film thicknesses smaller than the critical thickness may be responsible for the phenomenon that we have observed and directly related to the convergence angle itself. CONCLUSIONS: There seems to be experimental data supporting the use of traditionally taught convergence. Our study found that convergence angles between 6 degrees and 12 degrees seem to be optimum for tooth crown preparation when one plans to use zinc phosphate cement. Convergence angles of less than 6 degrees may not be desirable even if they can be clinically achieved. The results of our study indicate that a relationship exists between the convergence angle and the critical cement thickness that is necessary to realize the maximum strength properties of zinc phosphate cement.     

Low RF noise and power loss for ion-implanted Si having an improved implantation process

Very-low-transmission line noise of <0.25 dB at 18 GHz and low power loss /spl les/0.6 dB at 110 GHz have been measured on transmission lines fabricated on proton-implanted Si. In contrast, a standard Si substrate gave much higher noise of 2.5 dB and worse power loss of 5 dB. The good RF integrity of proton-implanted Si results from the high isolation impedance to ground, as analyzed by an equivalent circuit model. The proton implantation is also done after forming the transmission lines at a reduced implantation energy of /spl sim/4 MeV. This enables easier process integration into current VLSI technology.     

Semiautomatic implementation of protocols using an Estelle-Ccompiler

The basic ideas underlying an Estelle-C compiler, which accepts an Estelle protocol specification and produces a protocol implementation in C, are presented. The implementation of the ISO (International Organization for Standardization) class-2 transparent protocol, using the semiautomatic approach, is discussed. A manual implementation of the protocol is performed and compared to the semiautomatic implementation. The semiautomatic approach to protocol implementation offers several advantages over the conventional manual one, including correctness and modularity in protocol implementation code, conformance to the specification, and reduction in implementation time. Finally, ongoing development of a new Estelle-C compiler is presented     

Effect of spray nozzle design on liquid-solid contact in fluidized beds

In industrial fluid cokers the feedstock, consisting of heavy bituminous hydrocarbons, is atomized with steam and injected into a hot fluidized bed of coke. Good and uniform contact of the liquid droplets with the solid particles is required to provide heat for the cracking reactions while minimizing mass transfer effects. Experiments in a pilot plant coker have suggested that the initial particle/liquid mixing, in the spray jet, is rather poor. Experiments in a X-ray scanner showed that liquid droplets and entrained particles accumulate just below the tip of the jet plume to form agglomerates.An experimental technique was used to quantitatively determine the quality of mixing with a variety of nozzle configurations including several novel designs. By improving spray stability, redistributing liquid droplets to the solids-rich region of the jet and increasing the surface area of the gas-liquid jet-fluidized bed interface, liquid/solid contact is improved.     

Effects and properties of poly(arylene ether benzonitrile)s of various molecular weights blended with sulfonated poly(ether ether ketone)

Poly(arylene ether benzonitrile) (PAEBN) was synthesized with 2,6‐dichlorobenzonitrile and biphenol. PAEBNs with various molecular weights (MWs), 1,640,000 and 185,000 g/mol, were synthesized by control of the stoichiometry of the monomers and were blended with sulfonated poly(ether ether ketone) (SPEEK). The effects of MW on the water uptake, swelling, methanol permeability, and proton conductivity of the SPEEK/PAEBN blend membranes were investigated. The molecular mobility of the SPEEK/PAEBN blends was also examined in this study. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

An overview of electric vehicle technology

An overview of the present status and future trends in electric vehicle technology is provided. The emphasis is on the impact of rapid development of electric motors, power electronics, microelectronics, and new materials. Comparisons are made among various electric drive systems and battery systems. The market size of electric vehicles in the coming years and the potential electric vehicle impacts are discussed     

A knowledge-based expert system for gearing design application using Prolog and C

This paper describes the development of an expert system in gearing design application. The knowledge in this design field is vast and involves selection of appropriate data from large amounts of engineering standards data available in engineering catalogues and design handbooks. Experts very oftens have different opinions in determining the design solution. The theme of the work is to organise, systemise, conserve and spread this knowledge relating to gearing design and configuration.

There is a large number of design parameters involved in gearing design. The design of gears also requires an iterative approach to optimize these design parameters that govern the kinematic, as well as the strength performance. Owing to the complex combinations of these aspects, conventional design office practice tends to become complicated and time consuming. Hence, in this piece of work, attempts are made to formulate a design system capable of designing a required type of gear and its configuration under a specified set of working conditions.

The main features of the expert gearing design system are the use of semantic nets in representing the objects, a frame-based data acquisition and representation system, and production rules in representing the domain-specific knowledge base. The system provides a very user-friendly interface through the use of an expert system development tool Prolog. While Prolog is used to set up the various databases and the inference engine, the detail gear design calculations are performed by C. It is found that the communication between these two language media is excellent in terms of performance and efficiency.     

Role of imidazoline receptors in the cardiovascular actions of moxonidine, rilmenidine and clonidine in conscious rabbits

The present study in conscious rabbits with intracisternal (i.c.) catheters sought to determine the relative contribution of the I1 subtype of imidazoline receptors (IR) and alpha 2 adrenoceptors to the hypotensive effects of rilmenidine, clonidine and moxonidine with an I1-IR/alpha 2 adrenoceptor antagonist efaroxan and a specific alpha 2 adrenoceptor antagonist 2-methoxyidazoxan (2-MI). The alpha 2 adrenoceptor antagonist effect of efaroxan was compared with 2-MI by performing cumulative dose-response curves in the presence of alpha-methyldopa (400 micrograms/kg i.c.). 2-MI was 5.6 times more potent than efaroxan at reversing 75% of the hypotension elicited by alpha-methyldopa (P < .025). This dose ratio was used to match doses of efaroxan and 2-MI for similar alpha 2 adrenoceptor blockade. The effects of efaroxan (4.1, 13, 41 micrograms/kg i.c.) and 2-MI (0.74, 2.3, 7.4 micrograms/kg i.c.) were investigated on a single i.c. dose of rilmenidine (12 micrograms/kg), clonidine (0.75 microgram/kg) and moxonidine (0.51 microgram/kg). These doses of the antihypertensive agents, which were determined from cumulative dose-response curves, produce 90% of the maximum hypotension. Efaroxan was more effective at reversing the hypotension induced by moxonidine and rilmenidine than was 2-MI (P < .01). These findings suggest that rilmenidine and moxonidine act predominantly via IR. By contrast, 2-MI was more effective at reversing the clonidine-induced hypotension than was efaroxan (P < .001), suggesting that clonidine acts mainly via alpha 2 adrenoceptors in conscious normotensive rabbits. Thus, a higher selectivity of the second generation agents moxonidine and rilmenidine for I1-IR over alpha 2 adrenoceptors, compared with the first generation agent clonidine, appears to be necessary for this effect to be manifested in their hypotensive actions.