利用反射纵波评价裂缝倾角的模拟实验研究

声波全波列测井中的反射纵波可以用来评价高角度裂缝和对井周附近地质结构进行成像。目前的研究主要侧重于直接从波形资料处理出发计算裂缝的位置和倾角 ,其可靠性和准确性无从评价和校验。文中采用模拟实验的方法记录了倾角为 6 0°～80°范围内的 8种倾角裂缝的反射脉冲纵波波形 ,自行推导了反演裂缝倾角的公式 ,结合波场分离技术对实验测量波形数据进行了处理 ,计算出的裂缝倾角与实际值具有良好的一致性。本文结果表明 ,利用至少 2个深度点的纵波反射波波形资料就可以准确地反演裂缝的倾角     

A systematic techno-economic assessment of a WEC system installation for low-cost electrification of a habitable dwelling

This paper deals with the technical feasibility and economic viability of a grid connected wind-energy conversion system (WECS) used to cover the energy demand of an average habitable dwelling. The various parts of the wind-energy system are described and the useful electrical energy production is determined using a simulation program based on the Monte Carlo method. An economic analysis of the WEC system is performed using a computerized assessment tool. Important financial indices are calculated and financial scenarios investigated.     

Metal-insulator-semiconductor solar cell under gamma irradiation

The performance of a home made MIS–p-Si solar cell was experimentally studied under various gamma irradiation doses (up to 500 Mrad). The effect of radiation dose on the I−V and C−V characteristics was investigated in this work. The obtained results showed that all the output parameters of the cells under investigation were degraded with gamma radiation exposure. In addition, the effects of fabrication conditions (metal thickness and adding of antireflection coating) on the cell output parameters were also investigated.     

C/O能谱测井数据预处理的两点改进意见

简单介绍了碳氧比测井的原理及通常的数据处理方法。分析了由常规数据处理所得曲线仍然存在的问题及可能的成因 ,并给出了可行的修正办法。讨论了另一种可行的曲线异常数据的检测、剔除方法。实践表明 :文章讨论的两点建议都是可行的 ,并且在提高测量曲线质量的同时也提高了地层含油饱和度的解释精度。     

CMF300M355NU型质量流量计在油库汽车装车中的应用

介绍了质量流量计的工作原理有应用效果。这种新型质量流量计精度高，稳定性好，示值计量简便，可直接显示质量、流量、介质温度、密度等，维护量低，但必须正确安装、使用，才能发挥其应有的作用。     

Theoretical analysis of heat transfer in laminar pulsating flow

Pulsation effect on heat transfer in laminar incompressible flow, which led to contradictory results in previous studies, is theoretically investigated in this work starting from basic principles in an attempt to eliminate existing confusion at various levels. First, the analytical solution of the fully developed thermal and hydraulic profiles under constant wall heat flux is obtained. It eliminates the confusion resulting from a previously published erroneous solution. The physical implications of the solution are discussed. Also, a new time average heat transfer coefficient for pulsating flow is carefully defined such as to produce results that are both useful from the engineering point of view, and compliant with the energy balance. This rationally derived average is compared with intuitive averages used in the literature. New results are numerically obtained for the thermally developing region with a fully developed velocity profile. Different types of thermal boundary conditions are considered, including the effect of wall thermal inertia. The effects of Reynold and Prandtl numbers, as well as pulsation amplitude and frequency on heat transfer are investigated. The mechanism by which pulsation affects the developing region, by creating damped oscillations along the tube length of the time average Nusselt number, is explained.     

A comparison between the enhanced mass transfer in boundary and pressure driven oscillatory flow

Mass transport in pulsating flow devices using either moving boundaries or oscillating imposed pressure drops are compared with each other by means of a calculation using a simple model. We conclude that there is no difference between the two configurations as long as one is interested only in the power required to move the fluid for the convective mass transport achieved. However, the boundary driven configuration is more efficient if the power is divided by the total mass transport where both the diffusive and convective parts are taken into account, the boundary driven configuration is more efficient. The amplitude of the piston stroke in the pressure driven configuration and the amplitude in the boundary driven case are assumed to be the same, and the inertia of the moving devices themselves are ignored in this calculation.     

Discussion of "Hybrid-secondary-uncluttered induction (HSU-I)machine" [and closure]

J. Perahia comments on the paper by J. S. Hsu (see ibid., vol.16, p.192-7, 2001) and expands on the case of a two stator three phase squirrel cage induction machine where one stator housing is stationary and other stator housing is mounted on a worm gear assembly. The original author replies to the comments