Ab<Emphasis Type="Italic"> initio</Emphasis> investigation of boron diffusion paths in germanium

Boron is observed to diffuse very slowly in germanium, as opposed to its behaviour in silicon where it exhibits Transient Enhanced Diffusion effects in implanted samples. As a result of this slow diffusion, boron is a very stable dopant, allowing devices to be created with very well-defined doping regions. To understand this superior performance, calculations were performed on a variety of boron diffusion paths, within vacancy and interstitial mediated methods. It was found that the vacancy mediated diffusion which is associated with the fast diffusion of many other species in germanium exhibits a total barrier of 5.8 eV. Interstitial-mediated diffusion had a total barrier for migration of 3.4 eV in the neutral and singly negative charge states, 3.2 eV for the positive charge state, but a formation barrier of 4.1 eV. Thus the barrier for interstitial-mediated diffusion is dominated by the formation energy of the self-interstitial.     

Emission of trace toxic metals during pulverized fuel combustion of Czech coals

A study of the trace elements emission (As, Se, Cd, Co, Cr, Cu, Zn, Hg, Tl, Pb, Ni, Sn, Sb, V, Mn and Fe) from pulverized coal combustion has been made at six heating and power stations situated in the Czech Republic. The amount of chlorine in coal has considerable influence on volatilization of some elements such as Zn, Cu, Pb, Hg and Tl, which is explained by the formation of thermodynamically stable compounds of these elements with chlorine. Generally, the affinities for Cl follows the order Tl > Cu > Zn > Pb > Co > Mn > Sn > Hg. The experimental data indicates enrichment of some of the trace toxic elements in the emissions (Cu, Zn, As, Se, Cd, Sn, Sb, Hg and Pb) and good agreement was obtained by thermodynamic equilibrium calculations with a few exceptions. In the case of Fe, Mn, Co, Cr and Sn calculated values are overestimated in the bottom ash and there are zero predicted amounts of these elements in the fly ash. In comparison, the results from experiments show up to 80% of these elements retained in fly ash. This implies that there exist additional steps leading to the enrichment by Fe, Mn, Co, Cr and Sn of small particles. Such mechanisms could include the ejection during devolatilization of small inorganic particles from the coal of bottom ash particles, or disintegration of the char containing these metals to small particles of fly ash. On the other hand, there are slightly overestimated or similar values of relative enrichment factors for As, V, Cu, Cd, Sb, Tl and Pb in the fly ashes and zero predicted values for bottom ashes. Our experimental results show about 5% or less of these elements are retained in bottom ashes, so they probably remain in the bottom ash inside unburned parts of coal. Copyright © 2003 John Wiley & Sons, Ltd.     

Intermediate order in tetrahedrally coordinated silicon: evidence for chainlike objects

In this report, we describe the nature of intermediate order in silicon as determined by recent measurements on thin films using transmission electron microscopy (TEM) and Raman scattering. The TEM images show in addition to the expected continuous random network (CRN), the presence of highly ordered quasi-one-dimensional “chain-like objects” (CLO's) that are 1–2 nm wide and tens of nm long that meander and show some evidence of cross-linking with each other. The presence of these objects correlate to a Raman feature centered at 490 cm⁻¹ whose width is 35–40 cm⁻¹, and is used to quantify the heterogeneity in terms of the CLO and CRN (=475 cm⁻¹ scattering) concentrations. The 490 and 35 cm⁻¹ values are consistent with bond angle deviations approaching 0°, and thus reinforces an association with the CLOs. We find that in reference quality a-Si:H (made using pure SiH₄), the CLO concentration is about 5 vol%, while in state-of-the-art material using high H₂ levels of dilution during processing, it increases to about 15%. Increased stability of such material to light-soaking is thus not mediated by a direct volumetric replacement of poor with high-quality components. Rather, an important characteristic of intermediate order in silicon is the low-dimensional aspect of its order, which allows it to influence more total volume than which it is itself composed. Consistent with these and other recent findings, we propose a tensegrity model of amorphous silicon.     

Using internal fibre geometry to improve the performance of pin-loaded holes in composite materials

The anisotropic nature of fibre reinforced composites leads to large stress concentrations around pin-loaded holes through standard weave cloths. Proper understanding of how this anisotropic nature affects the load distribution around holes can be utilised to reduce these concentrations if sufficient thought is given to the internal fibre geometry near to the hole. Such local reinforcements need not be highly complex and can be readily produced without excessive effort, producing significant improvements in performance.     

The effects of observational feedback on treatment integrity in school-based behavioral consultation.

Evaluated the effects of performance feedback on levels of treatment integrity in school-based behavioral consultation. Three teachers employed in a residential treatment community were responsible for treatment implementation. Treatment integrity was defined as the percentage of 2-min intervals during which contingent teacher reinforcement for student on-task behavior was directly observed. Teacher and child behavior were monitored across baseline, traditional consultation, and consultation with performance feedback conditions in a multiple baseline design. Following a Problem Identification Interview and Problem Analysis Interview (J. R. Bergan, 1977), mean levels of treatment integrity for the 3 teachers ranged from 9% to 37%. The addition of a performance feedback package increased treatment integrity for all 3 teachers to levels ranging from 60% to 83%. The findings contribute to a growing literature supporting the need for direct assessment of treatment integrity in school-based consultation research and practice. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Assessment of renal osteodystrophy in dialysis patients: use of bone alkaline phosphatase, bone mineral density and parathyroid ultrasound in comparison with bone histology

Bone biopsies were studied in 73 patients to determine if a two-site radioimmunometric assay for serum bone alkaline phosphatase (BAP), total serum alkaline phosphatase (ALP), serum intact parathyroid hormone (iPTH), hand X-rays, regional bone mineral density (BMD) measurements and parathyroid enlargement detected by ultrasonography could accurately predict renal osteodystrophy. In the patients studied 57 had hyperparathyroid bone disease, 4 mixed renal osteodystrophy, 3 adynamic bone disease, 1 osteomalacia and 8 normal histology. Serum BAP, ALP and iPTH correlated positively with mineral apposition rate, osteoblastic, osteoid and eroded surface. In the diagnosis of hyperparathyroid bone disease serum iPTH was the most sensitive investigation, detecting 81% of patients at a level > 100 pg/ml but with a specificity of only 66%. Serum BAP was more sensitive, 70% at a level of > 10 ng/ml, than serum total ALP, 30% at a level of 300 IU/l, with similar specificities, 92 and 100%, respectively. Ultrasound detection of an enlarged parathyroid gland had a sensitivity of 64% and a specificity of 100% for the diagnosis of hyperparathyroid bone disease. Hand X-rays had a poor sensitivity, 47%, but a high specificity, 92%, for the detection of hyperparathyroid bone disease. The majority of patients had regional BMD values within the normal reference range and this test was of poor discriminatory value. The non-invasive markers were unable to distinguish between patients with low turnover, mild hyperparathyroidism and patients with normal histology. In conclusion the measurement of serum iPTH is a useful screening tool for the detection of hyperparathyroid bone disease which can be confirmed by the finding of a raised serum BAP or parathyroid enlargement. For definitive diagnosis, however, the gold standard remains bone biopsy and at present one cannot recommend any non-invasive method as an adequate substitute.     

Quenched BODIPY dye-labeled casein substrates for the assay of protease activity by direct fluorescence measurement

We have prepared casein conjugates of two BODIPY dyes for use as fluorogenic protease substrates in homogeneous assays. Both conjugates are labeled to such an extent that the dyes are efficiently quenched in the protein, yielding virtually nonfluorescent substrate molecules. These fluorogenic substrates release highly fluorescent BODIPY dye-labeled peptides upon protease digestion, with fluorescence increases proportional to enzyme activity. These quenched substrates are suitable for the continuous assay of enzymatic activity using standard fluorometers, filter fluorometers, or fluorescence microplate readers using either fluorescein excitation and emission wavelengths to measure BODIPY FL casein hydrolysis or Texas Red wavelengths to detect proteolysis of BODIPY TR-X casein. Most current techniques for detecting protease activity, such as the fluorescein thiocarbamoyl casein (FTC-casein) protease assay, require extensive manipulation, including separation steps, and are therefore labor intensive and error-prone. In comparison, we found the BODIPY dye-labeled casein protease assays to be simple and precise and to have greater sensitivity and a broader dynamic range of detection than the FTC-casein assay. We were able to sensitively detect the activities of a wide variety of enzymes with these new substrates, including serine, acid, sulfhydryl, and metalloproteases. We also found the assay suitable for quantitating protease inhibitor concentrations and for real-time analysis of proteolysis.     

What is driving health system change?

Socially amoral economic forces now drive health system change. The authors, assisted by a panel of experts on employers, health plans, providers, and consumers, discuss current drivers such as (1) employers' price-focused purchasing, without good quality/value measures; (2) health plans' growing successes and market clout; (3) providers declining prospects and fears about their future; and (4) consumers' worries about less choice. Future influences will include Medicare reforms, better information, and pro-consumer regulation of managed care, as well as rising social distress. The health system's future is now open for resolution in an evolving, imperfect market.     

Vector characterization of photodetectors, photoreceivers, andoptical pulse sources by time-domain pulse response measurements

Deconvolution of measurement system effects from pulse response measurements is demonstrated to yield reproducible, accurate characterization of the impulse response (and vector frequency response) of a photodetector or photoreceiver, as well as the intensity waveform of an optical pulse. Calibration is based on a <3-ps FWHM (full width at half maximum) optical pulse and a 50-GHz 3-dB bandwidth electrical sampling system. Vector characterization of a photodetector/photoreceiver to >40 GHz and an optical pulse source to >30 GHz are demonstrated. Calibration and effects of noise are discussed