Swelling of Hot-Pressed A12O3

Fully dense aluminas, prepared by hot-pressing, were found to swell during annealing at 1600°C in air, but not during annealing in a reducing atmosphere (po₂= 10^-7 Pa). The reaction followed the relation p - po = -K log t, where p_o and p are the initial and final densities, respectively, t is the time, and AT is a constant. The rate of swelling was enhanced by MgO solute. The reduction in density resulted from the nucleation and growth of grain-boundary pores. Pore formation was attributed to the reaction of carbon and sulfur impurities at the boundaries with oxygen, which had diffused down the grain boundaries from the ambient, to form CO/CO₂ and SO₂ gas at high pressures. Preliminary results indicate that this reaction can be avoided by preannealing powders in flowing oxygen prior to hot-pressing. The consequences of internal gas-forming reactions to other processes such as high-temperature creep and sintering are also discussed.     

Segregation of Isovalent Impurity Cations at the Surfaces of MgO and CaO

Enthalpies of segregation for isovalent impurities in magnesium and calcium oxide as a function of surface concentration were calculated by using an atomistic computer simulation method. We have considered Be²⁺, Mg²⁺, Ca²⁺, Ba²⁺, and Ni²⁺, segregating to both (001) and (110) faces. The results obtained can be extrapolated to predict the behavior of other impurities including Mn²⁺, Fe²⁺, and Co²⁺, We find, for example, that Fe²⁺, Mn²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ will concentrate at the (001) surface of MgO, while Ni²⁺ will be depleted. The enthalpy of segregation is found to vary substantially with coverage particularly for the larger impurities. The enthalpy becomes less negative with increasing impurity concentration due to the increasing lattice strain until the surface is nearly saturated. Then additional stabilization is obtained by restructuring of the surface layer. We predict reconstructed surfaces for both the (001) and (110) faces, which contain a high concentration of a larger impurity ion. The enthalpy of segregation shows a maximum at around 50% surface coverage implying a bimodal surface distribution of segregant. The influence of segregation on surface energy suggests two unusual effects. The (001) surface energy of the impure crystal becomes negative for surface concentrations of impurity greater than 10% Ba²⁺ or 75% Sr²⁺ in MgO. This implies a thermodynamic barrier to sintering. At high coverages of Ba²⁺ in MgO the (110) surface becomes more stable than the (001) face suggesting that facetting may occur.     

The aggregate-mortar interface

The aggregate-mortar interface is studied by scanning electron microscope and X-ray diffraction. This study confirmed that calcium hydroxide and ettringite are formed by a “through-solution” mechanism in this zone. The thickness of the transition phase depends on the size and shape of the sand particles. These originate their own surface effects which interfere with those caused by the large aggregate.     

45 GHz self-pulsation with narrow linewidth in quantum dot Fabry-Perot semiconductor lasers at 1.5 /spl mu/m

Self-pulsation at 45 GHz repetition frequency has been demonstrated in 1.5 /spl mu/m monolithic single-section quantum dot Fabry-Perot semiconductor lasers without saturable absorber. The mode-beating exhibits a narrow linewidth below 100 kHz, demonstrating high phase correlation between these modes. Such modelocked lasers open ways to low timing-jitter components for clock recovery or millimetre-wave generation in wireless transmission applications.     

Semiconductor-insulator structures in the phototargets of vidicons sensitive in the middle infrared region of the spectrum

The kinetics of electronic processes in vidicon phototargets based on semiconductor-insulator structures with a narrow-gap semiconductor is considered taking into account charge drain in the insulator layer and relaxation of the nonequilibrium depletion region in the semiconductor layer. The integration time, threshold sensitivity, and resolution at various intensities of incident radiation are estimated.     

Electrosynthesis and properties of N,N dimethylaniline

Poly-N,N-dimethylaniline was prepared by electrochemical polymerization of the monomer on gold, platinum and tin oxide electrodes in an acid medium. The polymer was characterized by cyclic voltammetry and scanning electron microscopy. Poly-N,N-dimethylaniline electrodes, modified by electrodeposition of palladium particles, were prepared.     

A stochastically optimized adaptive procedure for the location of MAS auxiliary monopoles: the case of electromagnetic scattering by dielectric cylinders

A genetically optimized technique that fully automates the potentially laborious allocation of the auxiliary monopoles for the method of auxiliary sources (MAS) is presented for the problem of electromagnetic (EM) scattering by isotropic dielectric cylinders with various cross sections. The proposed technique uses as input information not only the geometry of the scatterer but also the exciting field and the material properties of the cylinders are implicitly taking part in the optimization procedure. The resulting auxiliary surfaces, where the simulating monopoles are situated, are appropriately adapted to the original boundary surface and the MAS modeling is greatly facilitated. In addition, certain considerations are taken into account in order to avoid undesirable numerical dependencies between the fictitious monopoles. Finally, the accuracy of the numerical method combined with overdetermined systems of equations is examined for isotropic cylinders of various geometries and dielectric characteristics.