啤酒酵母菌种的石蜡保藏技术

啤酒酵母菌种用液体石蜡技术保藏具有设备简单、操作方便,成活率高,变异少,优良种性能保持较长时间的优点,实用价值高。本文从液体石蜡保藏菌种的机理、保藏效果、保藏等具体技术操作及其使用方法都作了较为详细的介绍,相信能为啤酒菌种的保藏带来较大的好处。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

狭小场地条件下大跨度预应力混凝土拱板的运输及吊装

介绍了大跨度预应力混凝土拱板在狭小场地条件下的起模、运输及空间滑移吊装的方法，经在众多中直粮库中的应用，证明该方法简单、适用、经济。     

In-Situ observation on microfracture behavior ahead of the crack tip in 63Sn37Pb solder alloy

in-situ transmission electron microscopy (TEM) tensile tests on as-cast and aged 63Sn37Pb solder alloys were conducted, and the fracture behavior in nanometer scale ahead of the crack tip was inspected and discussed. Results show that the fracture was completed by connecting the discontinuous cracks or voids. Dislocation behavior was concentrated along the grain boundaries for as-cast samples, and displayed mainly as dislocation climb. The crack was intergranular dominated under the lower strain rate. While remarkable mutual dislocation emission was detected in the aged solder. Transgranular cracks were dominant in the fractured area, and they propagated by linking up with the nanometer scale cracks ahead of the crack tips under the effective promotion of the inverse dislocation emission. At the same time, the partial interphase or intergranular cracks in the thinned area were also found. Under this condition, a new critical stress intensity factor K _c ^′ to define the mutual dislocation emission was proposed.     

印染废水处理工艺研究及实例

本文简要介绍了印染废水水质特征,提出了处理工艺,并利用两个工程实例说明了该工艺的可行性.     

PTA压力离心机转子的改造

介绍了PTA压力离心机的主要性能参数、工作原理、分离效果的影响因素。为了增大沉渣在过渡区及脱水区滞留的时问，同时为达到在过渡区及脱水区对沉渣加入纯净水进行再冲洗的目的，对螺旋送料转子、挡液环、进料管进行了改造。改造后，沉渣在脱水区的停留时间由0．44a增至0．72s，2．5～3t／h的冲洗水对脱水区的沉渣进行冲洗效果较好。产品中的杂质质量分数较改造前减少15％，产品优等品率提高到99％。     

Onset of buoyancy-driven convection in melting from below

When a horizontal homogeneous solid is melted from below, convection can be induced in a thermally unstable melt layer. In this study the onset of buoyancy-driven convection during time-dependent melting is investigated by using similarly transformed disturbance equations. The critical Rayleigh numbers based on the melt-layer thickness are found numerically for various conditions. For small superheats, the present predictions approach the well known results of classical Rayleigh-Bénard problems, that is, critical Rayleigh numbers are located between 1,296 and 1,708, regardless of the Prandtl number. However, for high superheats the critical Rayleigh number increases with an increase in phase change rate but with decrease in Prandtl number.     

Characteristics of Milk Powders Produced by Spray Freeze Drying

Skim and whole milk powders were manufactured at lab scale by spray freeze drying (SFD), using liquid nitrogen as the cryogen. The polydispersity of droplet/particle sizes was limited using an encapsulator nozzle to atomize the feed. Particle morphology was examined using a scanning electron microscope. Samples were compared with equivalent spray-dried powders in tests of wettability and dissolution in water. The spray freeze-dried powders were found to be highly porous, with a uniform structure of pores throughout the entire particles. When tested in water, SFD skim milk powders wetted roughly three times as fast as industrially spray-dried agglomerated skim milk powders and were observed to dissolve rapidly by breaking down into smaller particles.