An access detection and machine cycle tracking system for machine safety

Abrasive water jet (AWJ) machining is characterized by its versatility, i.e., it can be applied to a wide variety of materials. Currently, one important application is for manufacturing gem artifacts, especially agate, which is the largest gemological material produced in the state of Rio Grande do Sul. However, one of the main obstacles to its popularization is the cost associated with the process, due to the high abrasive consumption required for a good quality surface finish. In this sense, this research paper presents a study of the influence of the main process parameters (traverse speed and abrasive mass flow rate) on the surface finish of agates machined by AWJ. The experimental procedure used three different traverse speeds, four abrasive mass flow rate in two different thicknesses of agate’s plates. Surface roughness and angle of striation marks were observed for different depths from the jet entrance surface. Results were analyzed using analysis of variance (ANOVA). Through the study, it was found that the machined surface finish varies according to the depth from the entrance surface of the abrasive jet. Also, it was concluded that the surface finish of the machined surface by AWJ (surface roughness and striation marks) of the agate’s plates machined by AWJ exhibits similar results for both thicknesses tested. ANOVA showed that the traverse speed is more significant than abrasive mass flow rate for the material studied with respect to the surface finish. Thus, for a small material thickness, it is possible to use high traverse speed and low abrasive mass flow rate which makes the process more economical.     

Use of an environmental specimen bank for evaluating the impact of the Prestige oil spill on the levels of trace elements in two species of Fucus on the coast of Galicia (NW Spain)

In the present study we investigated possible contamination by trace elements due to the oil slick caused by the shipwreck of the Prestige oil tanker, in two species of brown macroalgae (Fucus vesiculosus and Fucus ceranoides) collected from the coastal area most severely affected by the spill (Galicia, NW Spain). The oil slick apparently did not cause significant increases in the concentrations of the trace elements studied, except vanadium. It appears that the magnitude of terrestrial inputs to coastal waters is sufficiently high to mask the inputs of trace elements from the fuel. The observed exception of V suggests that bioaccumulation of this element by the two species of Fucus may be used to indicate exposure to petrochemical products similar to the Prestige fuel. The findings of the study are another example of the importance of the existence of Environmental Specimen Banks for studies of this type.     

On the efficiency of quantization-based integration methods for building simulation

Models describing energy consumption, heating, and cooling of buildings usually impose difficulties to the numerical integration algorithms used to simulate them. Stiffness and the presence of frequent discontinuities are among the main causes of those difficulties, that become critical when the models grow in size. Quantized State Systems (QSS) methods are a family of numerical integration algorithms that can efficiently handle discontinuities and stiffness in large models. For this reason, they are promising candidates for overcoming the mentioned problems. Based on this observation, this article studies the performance of QSS methods in some systems that are relevant to the field of building simulation. The study includes a performance comparison of different QSS algorithms against state-of-the-art classic numerical solvers, showing that the former can be more than one order of magnitude faster.     

Linear regression-based multifidelity surrogate for disturbance amplification in multiphase explosion

Structural and Multidisciplinary Optimization - When simulations are very expensive and many are required, as for optimization or uncertainty quantification, a way to reduce cost is using...     

Electrically conductor black zirconia ceramic by SPS using graphene oxide

The use of graphene as a component for developing electroconductive ceramic composites is being profusely studied. It is a very promising additive as it has excellent mechanical properties, high electrical and thermal conductivities, it is lightweight and its aspect ratio allows reaching percolation with low contents.In the particular case of zirconia, preparation of black coloured materials remains a challenge while many high added value applications are waiting for a solution. Graphene appears as a candidate for fulfilling all these requirements. In this work, 3Y–TZP/rGO composites were prepared by Spark Plasma Sintering Zirconia-rGO mixtures. Simultaneous sintering and in-situ reduction of graphene oxide opens a very interesting technological route for preparing this type of materials. The influence of graphene content on the electrical, mechanical and optical properties was studied. An rGO content as low as 0,29 vol% allows nanostructured black zirconia to be obtained but it has to be increased up to 1 vol% in order to reach electrical resistivity values <100Ωcm, required for electrodischarge machining.     

Prebiotic Origin of Pre-RNA Building Blocks in a Urea “Warm Little Pond” Scenario

Urea appears to be a key intermediate of important prebiotic synthetic pathways. Concentrated pools of urea likely existed on the surface of the early Earth, as urea is synthesized in significant quantities from hydrogen cyanide or cyanamide (widely accepted prebiotic molecules), it has extremely high water solubility, and it can concentrate to form eutectics from aqueous solutions. We propose a model for the origin of a variety of canonical and non-canonical nucleobases, including some known to form supramolecular assemblies that contain Watson-Crick-like base pairs.The dual nucleophilic-electrophilic character of urea makes it an ideal precursor for the formation of nitrogenous heterocycles. We propose a model for the origin of a variety of canonical and noncanonical nucleobases, including some known to form supramolecular assemblies that contain Watson-Crick-like base pairs. These reactions involve urea condensation with other prebiotic molecules (e. g., malonic acid) that could be driven by environmental cycles (e. g., freezing/thawing, drying/wetting). The resulting heterocycle assemblies are compatible with the formation of nucleosides and, possibly, the chemical evolution of molecular precursors to RNA. We show that urea eutectics at moderate temperature represent a robust prebiotic source of nitrogenous heterocycles. The simplicity of these pathways, and their independence from specific or rare geological events, support the idea of urea being of fundamental importance to the prebiotic chemistry that gave rise to life on Earth.     

Solar drying of sawn lumber in Spain

A solar heated experimental drying kiln was installed in Madrid (INIA-Forest Industries Department) to study the efficiency of solar drying of sawn lumber in Spain, as compared with normal air drying. The kiln has been designed as a low cost semi-greenhouse type, but was equipped with a semi-automated control of the drying schedules. The performance of the solar kiln has been studied during ten test runs over a period of two years particularly with respect to drying rate, initial and final wood MC, reliability and efficiency. The results have proven that the solar kiln is capable of drying (economically) from an initial moisture content of 70 to 80%, to a final MC of 8 to 10% up to 3.5 times faster than air drying. With respect to checks, splits and internal stresses, the final wood quality is mostly better, not only compared to normal air drying but also to conventional kiln drying.