Chromium (VI) removal by methylated biomass of Spirulina platensis: The effect of methylation process

Biosorption of heavy metals is an interesting approach to treat industrial wastewaters by an environmentally friendly system. Spirulina platensis biomass, an effective biosorbent for cations, cannot be used to adsorb chromate due to its negatively charged surface close to neutral conditions; therefore, methylation of biomass was performed to increase its adsorption capacity under these conditions. Batch adsorption tests carried out varying both Cr(VI) and methylated biomass concentrations showed that 2–4 g l^?1 of biosorbent were able to remove Cr(VI) with efficiency ≥80%, while higher Cr(VI) levels (43–50 mg l^?1) showed low removal efficiency. The model of Langmuir was shown to describe the adsorption phenomenon better than the Freundlich one. The values of the overall adsorption capacity of methylated biomass suggested that increased biosorbent availability does not necessarily correspond to larger amount of adsorbed metal. FT-IR spectra of dried and methylated biomass of S. platensis allowed us monitoring the efficiency of the methylation process through the analysis of CH and COO^? vibrational stretching modes, taken as diagnostic of this process.     

Pt–Ba–Al2O3 for NOx storage and reduction: Characterization of the dispersed species

Pt–Ba–Al₂O₃ active and selective for NO_x storage and selective reduction to N₂ has been prepared and tested. Characterization of the parent Al₂O₃, Pt–Al₂O₃ and Ba–Al₂O₃ materials, as well as of Pt–Ba–Al₂O₃ catalyst in the oxidized, reduced and sulphated state has been performed by FT-IR spectroscopy of low-temperature adsorbed carbon monoxide and of adsorbed acetonitrile. XRD, TEM and XPS analyses have also been performed. Evidence for the predominance of Ba species, which are highly dispersed on the alumina support surface, and may be carbonated or sulphated, has been provided. Competitive interaction of Pt and Ba species with the surface sites of alumina has also been found.     

Anodic,cathodic and combined treatments for the electrochemical oxidation of an effluent from the flame retardant industry

The electrochemical oxidation of an effluent from the manufacture of phosphorus based flame retardants was studied. To reach a residual concentration of reduced phosphorus lower than 10 mg L⁻¹, in compliance with Italian law for industrial wastewater disposal, anodic oxidation using a boron-doped diamond (BDD) anode and electro-Fenton (EF) treatment were tested. The effects of some factors are optimised and a comparison of the reaction pathways is also presented. A combined treatment using EF with BDD conducted in an undivided cell is shown not to enhance the data obtained with BDD while a novel combined treatment using EF and BDD in a divided cell shows promising results when an anionic membrane is used as separation. In this last case the cell operates as two different batch reactors working with the same current. The anodic compartment, fed with raw effluent, provides partial oxidation, while the cathodic compartment, fed with the partially anodically oxidised solution, completes the treatment. When the effluent is transferred in the cathodic compartment, the anodic one is fed with fresh untreated solution. The advantage of this kind of coupling consists in the simultaneity of the two treatments which allows total oxidation with notable saving of charge and time.     

Interaction of inositol phosphate with calcite

The interaction of myo-inositol hexaphosphate with calcite was studied to evaluate the adsorption mechanisms and the electrochemical modifications induced by interaction of a molecule at such a high-charge density. In addition to quantitative information through the construction of adsorption isotherms, FT-IR and Laser Doppler Velocimetry - Photon Correlation Spectroscopy (LDV-PCS) were employed to investigate the nature of the adsorbent-adsorbate bonds and to determine the electrophoretic mobility and size of the particles before and after sorption. The experiments were also run with orthophosphate (Pi) for comparison. The amount of sorbed P increased to reach a plateau at 17.8 mol m^-2 for inositol hexaphosphate (IHP) while for Pi rose 1.4 mol m^-2 but at C_e > 610^-4 M it had a sharp increase reaching 155 mol m^-2. As expected, for Pi, adsorption predominated up Ce 610^-4 M by covering about 20% of total surface. The adsorption occurred at sites that behaved as nucleus of formation of the clustering of Ca- and PO₄-ions with the ending formation of calcium phosphate precipitates at C_e higher than 610^-4 M. The reaction of inositol hexaphosphate with calcite involves, besides adsorption, precipitation of Ca salts and hence calcite dissolution also at the lowest added IHP concentrations, accounting for the large amount retained by calcite. Sorption of IHP on calcite caused aggregation of particles at low concentrations followed by an increase of their negative charge and hence re-dispersion at higher concentrations. These results indicate a great IHP-fixing capacity of calcite that can affect its accumulation in soils and P bioavailability, and a considerable change of calcite electrochemical properties and particle size distribution that can modify aggregate stability.     

Coupling Interrupted Fischer and Multicomponent Joullié-Ugi to Chase Chemical Diversity: from Batch to Sustainable Flow Synthesis of Peptidomimetics

The generation of peptidomimetic substructures for medicinal chemistry purposes requires effective and divergent synthetic methods. We present in this work an efficient flow process that allows quick modulation of reagents for Joullié-Ugi multicomponent reaction, using spiroindolenines as core motifs. This sterically hindered imine equivalent could successfully be diversified using various isocyanides and amino acids in generally good space-time yields. A telescoped flow process combining interrupted Fischer reaction for spiroindolenine synthesis and subsequent Joullié-Ugi-type modification resulted in product formation in very good overall yield in less than 2 hours compared to 48 hours required in batch mode. The developed protocol can be seen as a general tool for rapid and facile generation of peptidomimetic compounds. We also showcase preliminary biological assessments for the prepared compounds.     

X-ray Fluorescence Uptake Measurement of Functionalized Gold Nanoparticles in Tumor Cell Microsamples

Quantitative cellular in vitro nanoparticle uptake measurements are possible with a large number of different techniques, however, all have their respective restrictions. Here, we demonstrate the application of synchrotron-based X-ray fluorescence imaging (XFI) on prostate tumor cells, which have internalized differently functionalized gold nanoparticles. Total nanoparticle uptake on the order of a few hundred picograms could be conveniently observed with microsamples consisting of only a few hundreds of cells. A comparison with mass spectroscopy quantification is provided, experimental results are both supported and sensitivity limits of this XFI approach extrapolated by Monte-Carlo simulations, yielding a minimum detectable nanoparticle mass of just 5 pg. This study demonstrates the high sensitivity level of XFI, allowing non-destructive uptake measurements with very small microsamples within just seconds of irradiation time.