Effect of water inclusions on charge transport and polarization inporous media

Wideband dielectric spectroscopy measurements (100 Hz to 10 GHz) were carried out on different microporous systems (including sintered glass filters, sandstone and carbonate rocks) saturated with brine (electrolytic water solution) and a hydrocarbon oil at different relative fractions. Three main contributions were singled out in the dielectric spectra: low frequency dispersion (LFD) effects (<100 kHz) related to long range ionic transport and dependent on the connectivity of the water phase; Maxwell-Wagner-Sillars (MWS) polarization effects (100 kHz to 1 GHz), essentially controlled by the shape of the water inclusions; and high-frequency effects (>1 GHz) due to short-range ion transport and related to specific pore surface. For each analyzed system, oil-wet (o-W) and water-wet (w-w) samples were obtained by chemical treatment of the pore surfaces. Systematic differences were observed in the electrical response on varying wettability (and so the respective distribution of the fluids in the pore space). Parameters such as the loss tangent value, the strength and the exponent of the LFD power law, as well as the characteristic time and strength of the MWS relaxation were good indicators of wettability. Results were discussed by using some standard models that account for the pore wettability effects on dielectric spectra. A new method for wettability determination of reservoir rocks from both laboratory and borehole electric measurements was presented     

Benzodioxoles as alternative coinitiators for radical polymerization in a model‐dental adhesive resin

This study evaluated the effectiveness of benzodioxole derivatives as coinitiators of radical polymerization in a model‐dental adhesive resin. To compose the adhesive resin, a monomer mixture based on 50 wt % of Bis‐GMA, 25 wt % of TEGDMA, and 25 wt % of HEMA was used. Camphorquinone (CQ) 1 mol % was used as a photoinitiator to initiate polymerization. 1,3‐Benzodioxole (BDO) and piperonyl alcohol (PA) were used as coinitiators at 0.25, 0.5, 1, 2, 4, 8, and 16 mol % level. In addition, tertiary amine, ethyl 4‐dimethylamino benzoate (EDAB) was used as coinitiator in the control group. Some physical, chemical, and mechanical properties of the polymer formed in the experimental adhesives were evaluated using the kinetics of polymerization, sorption and solubility, flexural strength, and elastic modulus tests. The results indicated that BDO and PA were effective coinitiators in the photoinitiator system based on CQ. Comparisons between the benzodioxoles derivative coinitiators and EDAB showed similar performance in the kinetics of polymerization and flexural strength. For water sorption and solubility evaluation, BDO and PA demonstrated significantly more sorption of water and less solubility than the EDAB control group. The findings suggest that BDO and PA were feasible alternatives to conventional amine as coinitiator. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Microscopical features in retrieved human Branemark implants: a report of 19 cases

The authors present a histologic analysis of 19 Branemark titanium implants retrieved for different causes: four implants were removed for abutment fracture, one for dental nerve dysesthesia, two for bone overheating, two for peri-implantitis, nine for mobility, one for unknown causes. In the implants removed for fracture a high bone-implant contact percentage was present (71.83 +/- 4.96%) with compact, mature bone at the interface. The picture of the failure due to bone overheating was characteristic with the presence of bone sequestra and of a gap between implant and bone filled by lymphocytes and plasma cells: many bacteria surrounded the necrotic bone and no newly regenerated bone was present. In peri-implantitis an inflammatory infiltrate was observed in the peri-implant tissues: a dense fibrous connective tissue was present around implants failed for mobility. The microscopical picture is certainly extremely important in identifying the causal determinants of an implant failure.     

A very short planar silica spot-size converter using a nonperiodicsegmented waveguide

To reduce the coupling loss of a fiber-to-ridge waveguide connection, a planar silica spot-size converter for a wavelength of 1.55 μm is implemented in the form of a nonperiodic segmented waveguide structure with irregular tapering. A simple single-step lithography process is sufficient for the fabrication of the planar structures. An evolutionary algorithm has been successfully applied for the optimization. The simulated results obtained with a three-dimensional (3-D) finite difference beam propagation method (FD-BPM) program are compared with measurements of implemented couplers, showing very good agreement. A waveguide-to-fiber coupling efficiency improvement exceeding 2 dB per converter is shown. Structures obtained with this approach are very short (~140 μm) and simple to integrate on the same wafer with other planar structures such as phased arrays or ring resonator structures     

Comparison of simulation and measurement of dynamic fiber-coupling effects for high-speed multimode VCSELs

Static and dynamic measurements are performed with GaAs oxide-confined vertical-cavity surface-emitting lasers (VCSELs), using multimode fibers with a core diameter of 50 and 62.5 /spl mu/m and different numerical apertures (NAs). They show that a small NA can have a severe impact on the eye opening and thus also on the bit-error rate. The measurements are analyzed with a spatiotemporal two-dimensional (2-D) multimode VCSEL model. The required parameter extraction for the model is verified with small- and large-signal measurements. The analysis shows that the change of the eye opening can be explained by the interaction between the mode- and the current-injection profile, carrier diffusion, and intermodal gain compression (IGC). IGC increases differences in the modal power distribution caused by the interaction between the mode profiles and the current-injection profile. Carrier diffusion is able to compensate these increased differences of the modal power distribution. Its impact, however, on dynamic changes caused by IGC is moderate.     

Determination of sensory thresholds of Mentha piperita L. essential oil in selected tropical fruit juices and efficacy of sensory accepted concentrations combined with mild heat to inactivate foodborne pathogens

This study determined the compromised acceptance threshold (CAT) and rejection threshold (RT) of Mentha piperita L. essential oil (MPEO) in cajá, guava and mango juices. The MPEO concentrations below the RT values were evaluated alone or combined with mild heat treatment (MHT; 54 °C) to inactivate ≥5-log₁₀ of Escherichia coli O157:H7 and Salmonella Enteritidis PT 4 in the same juices. The CAT of MPEO varied from 0.30 to 0.32 μL mL⁻¹, while the RT was 1.34 or 1.36 μL mL⁻¹ in the tested juices. Only concentrations of MPEO close, or higher than the RT caused ≥5-log₁₀ reductions in the tested pathogens in cajá, guava and mango juices. Combined with MHT, concentrations of MPEO below the RT reduced ≥5-log₁₀ of both pathogens in juices. These findings indicate that MPEO concentrations below the RT in combination with MHT is a feasible preservation technology to ensure the safety of tropical fruit juices.     

Experimental characterisation of a CuAg alloy for thermo‐mechanical applications. Part 2: Design strain‐life curves estimated via statistical analysis

Strain‐life fatigue data on copper alloys, especially type CuAg, are seldom available in the literature. This work fills this gap by estimating the strain‐life curves of a CuAg alloy used for thermo‐mechanical applications, from isothermal low‐cycle fatigue tests at 3 temperatures (room temperature, 250°C, 300°C). Regression analysis is used to estimate the median fatigue curves at 50% survival probability. The comparison of median curves with the Universal Slopes Equation model, calibrated on monotonic tensile properties, shows a fairly good agreement. Design strain‐life curves with a lower failure probability and given confidence are estimated by several approximate statistical methods (“Equivalent Prediction Interval,” univariate tolerance interval, Owen's tolerance interval for regression). When higher survival probabilities are considered, the results show a marked decrease in the allowable design strain at a prescribed fatigue life. The suggested procedure thus improves the durability analysis of components loaded thermo‐mechanically.