Tensile strength of polyurethane exposed to nitrogen dioxide

Polyurethane prepared from tetramethylene glycol and diisocyanate was exposed in the form of films to small pressures of NO₂ and to NO₂ plus air. Tensile strength was measured as a function of exposure time and temperature with an apparatus especially constructed for the purpose of measuring mechanical properties in different environmental “atmospheres.”     

Effects of Particle Size on the Fusion of Soda–Lime–Silicate Glass Containing NaCl

The coupled effects of particle size and 1 wt% NaCl additions on the sequence of melting reactions in a multicomponent system (sand–soda ash–calcite–dolomite–feldspar) were studied using data from DTA, DTGA, and XRD interactively. Glass batches varied in average particle size from 250 μm to finer than 45 μm. Milestone events in the fusion process of the coarse particle base glass were elucidated. The termination temperature of the last significant reaction associated with CO₂ release was 35°C lower in the fine particle size batch than with the coarsest batch. Liquid-phase formation at ∼523°C in the batch with 1 wt% NaCl occurred to an increasingly sizable extent with decreasing particle size. This contrasts with a similar effect at ∼630°C for a comparable batch without NaCl via eutectic melting between soda ash and dolomite. Sodium chloride additions significantly enhanced dissolution of CaO relic.     

A new batch solvent-extraction pilot plant

Summary and Conclusions A new improved batch solvent extraction plant and its versatility of design have been described. Data have been given on the cost and initial test operations. The performance of the plant has been tested, and its value as a research tool has been demonstrated by the production of free gossypol and meals low in gossypol for use in research. Simplicity of operation is borne out by the fact that only one operator is needed. A limited number of detail drawings of the plant are available on written request from the Southern Regional Research Laboratory. Presented at the fall meeting, American Oil Chemists’ Society, Nov. 2–4, 1953, in Chicago, Ill. One of the laboratories of the Southern Utilization Research Branch, Agricultural Research Service, U. S. Department of Agriculture.     

The effect of processing conditions upon the nutritional quality of vegetable oils

On the basis of the chemical, physical, and biological criteria used, all of which have been shown to be sensitive indicators of heat damage to oils, it must be concluded that the overall nutritional quality of an oil is not adversely affected by alkali refining, adsorptive decolorizing, or deodorization; that higher temperatures of deodorization (238C) produce oils nutritionally equivalent to those deodorized at lower temperatures (160C); and that the normal processes used in manufacturing edible oils improve the resistance of these oils to heat damage. Presented at the 6th Congress of the International Society for Fat Research, London, 1962.     

Kinetic modelling of the catalytic conversion of synthesis gas

A kinetic study for the one-step conversion of synthesis gas to gasoline on a ZnO–Cr₂O₃–ZSM-5 catalyst is described. On this catalyst, three reactions are involved in the overall transformation of synthesis gas: the methanol synthesis, the conversion of methanol to hydrocarbons and the water–gas shift reaction. Under the operating conditions selected for the study, it was found that the water–gas shift was at equilibrium and the methanol was completely converted to hydrocarbons. Consequently, it was postulated that the kinetics of the limiting reaction step, the methanol synthesis on the ZnO–Cr₂O₃ component, was the one that controls the overall reaction rate. Three kinetic model equations describing the rate of synthesis gas conversion on the bifunctional catalyst, were considered to fit the data of the experimental runs performed in a Berty well-mixed reactor. Those equations were derived under very special conditions where the methanol decomposition term could be neglected. It was also observed that in the kinetic equations a term involving the fugacity of CO₂ was required to predict the rate properly. The catalyst deactivation was also taken into account in the analysis.     

EMI shielding of intinsically conductive polymers

Results of this study, in which shielding efficiencies are measured for a number of blends containing various conductive fillers including intrinsically conductive polymers, are reported. It is shown that a very high level of shielding performance can be achieved by use of intrinsically conductive polymers in thermoplastic blends and that the most reliable measure of this performance is obtained from far-field shielding measurements. However, near-field measurements provide a useful method for comparing the relative shielding effectiveness of different samples. A PVC blend containing nearly uniformly dispersed intrinsically conductive polymer proved to be the best performing sample.     

Tensile behavior of glass fiber-reinforced acetal polymer

The tensile stress-strain behavior of glass fiber-reinforced polyacetal resin was investigated for various fiber concentrations, fiber length distributions, and finishing agents. The polyacetal fiber blends change considerably in strength and elongation at break when treated with ammonium chloride, but otherwise similar specimens still follow a common stress-strain curve to a point shortly before failure. As the mean fiber length decreases, the modulus and tensile strength fall, but the elongation at break remains almost unchanged. The observed tensile behavior is discussed in terms of a simplified model, which assigns the fibers to two categories: a fraction α parallel to the applied load, and the remainder distributed in a plane perpendicular to the load axis. By fitting this model to the stress-strain curves, two other constants of each system are derived: a length-dependent efficiency factor β for parallel fibers, whose magnitude agrees with the predictions of Rosen and his co-workers, and a factor γ which expresses the constraint of the matrix resin by the “transverse” fibers. The behavior of γ is consistent with Tsai's theory of the transverse modulus of laminates, if a reasonable amount of fiber–fiber contact is assumed. In terms of this model, possible interpretations of the behavior under repeated loading and the mechanism of tensile failure are presented.