Diffraction of millimeter waves by projecting a shadow pattern onto a semiconductor

The transmission of millimeter waves through a semiconductor changes according to the amount of light falling on it. In the experiments reported here, a pattern of light and shadow is projected onto a sheet of semiconductor and the regions of greater and lesser transmission serve as a diffracting object for a millimeter-wave beam. The light source is a quartz tungsten halogen lamp. A lock-in amplifier is employed to overcome difficulties due to the differences in transmitted power being small.     

A study of reinforced refractory concretes

Results of a laboratory study of the properties of corundum concrete with metallic fibers of five compositions are presented. It is shown that some of the fibers affect favorably the strength and heat resistance of the concrete. Industrial tests of parts made of the suggested reinforced concrete have proved these conclusions.Translated from Ogneupory i Tekhnicheskaya Keramika, No. 11, pp. 22–24, November, 1996.     

Growth and characterization of hot-wall epitaxial CdTe on (111) HgCdTe and CdZnTe substrates

Thin CdTe films were deposited by hot-wall epitaxy (HWE) on (111) HgCdTe and CdZnTe substrates at temperatures from about 140 to 335°C. X-ray rocking curves were used to show that crystal quality of the CdTe (111)B films improved as substrate temperature increased from 140 to about 250°C. Rocking curve values for full width at half maximum (FWHM) decreased from 2–4 degrees at 140–150°C to less than 100 arc-s at 250°C, and a FWHM of 59 arc-s was the lowest value observed near 250°C. The FWHM of the HWE CdTe was found to be insensitive to growth rate below about 400Å/min, but increased to four degrees at 1250Å/min. X-ray diffraction confirmed that films grown on the B-face at higher temperatures were epitaxial, but contained a significant volume fraction, 35% to 50%, of rotational in-plane twins. Electron microscopy confirmed a coarse twin density, and photoluminescence spectra showed an absence of excitonic emission in the HWE films. Simultaneous growth on two (111) HgCdTe substrates with different surface polarities between 230°C and 335°C showed that deposition rate on the A-face decreased relative to that on the B-face as temperature increased. Films grown on the B-face exhibited better surface morphologies than those grown on the A-face.     

Issues in nonlinear stochastic grey box identification

Grey box identification refers to the practice of identifying dynamical systems in model structures exploiting partial prior information. This contribution reviews a method for stochastic grey box identification and surveys experiences and lessons of applying it to a number of industrial processes. Issues to be addressed include advantages and costs of introducing stochastics into the model, the question of what contribution must be expected from the model designer as opposed to what can be formalized in computer algorithms, and an outlook on future plans to resolve present shortcomings.     

Theoretical and Experimental Study of Water Transport in a Hollow Cylinder Applied to the Drying of Round Squid Mantle

Until now, attention has been focused solely in the drying of squid mantle from an experimental point of view, neglecting the transport phenomenon studies of water in squid muscle. This work studies the drying of squid mantle (Loligo brasiliensis), previously salted and smoked by liquid smoking (hickory extract), using a tubular dryer in closed cycle with a silicagel fixed bed in series. The mass transfer phenomenon during drying was studied, based on the Fick's second law, with the effective diffusivity supposed constant, which enabled an analytical solution to the problem. The drying curve calculated with the resulting equation was compared with experimental data. The model was applied to a hollow cylinder geometry (round squid mantle), with its internal surface isolated from the drying environment by a plastic film. The latter was given a tubular form and introduced inside the mantle cavity (impervious wall boundary condition).     

Pathway engineering for the production of aromatic compounds in Escherichia coli

The standard enzymatic assay for quantification of D-sorbitol in plasma was adapted to the automatic analyzer Cobas Mira S. In the assay, NAD (reagent) in the presence of sorbitoldehydrogenase (SDH; start reagent) converts D-sorbitol to fructose with formation of NADH, which was detected automatically as the difference between the first and last readings at 340 nm. The sample blank values for each specimen were subtracted to exclude both endogenous D-sorbitol and sugars, which also react as substrates for SDH. The method is simple, rapid (40 samples/h), precise down to endogenous concentrations (coefficient of variation < 5%; limit of determination: 0.38 mg/L) and linear up to 100 mg/L. Samples with higher D-sorbitol concentrations were estimated after dilution. The method was used to measure disposition curves of sorbitol in volunteers after a single intravenous dose of 0.8 g sorbitol.     

Structured genetic algorithm for robust H∞ controlsystems design

A structured genetic algorithm (SGA) approach is developed for robust controller design based on the concept of an H^∞ loop-shaping technique and the method of inequalities. Such an SGA is capable of simultaneously searching the orders and coefficients of the precompensator and postcompensator for the weighted plant. It is, therefore, not necessary to predefine the order of compensators as in usual practice. A multiple objective ranking approach is also incorporated so that the design criteria of extreme plants can be easily achieved. The effectiveness of such a technique is illustrated by a high-purity distillation column design example     

PLATOP: a novel planarized trench isolation and field oxideformation using poly-silicon

A novel isolation scheme named planarized trench isolation and field oxide formation using poly-silicon (PLATOP) Is described. PLATOP is applicable to high-performance submicron VLSI since it results in encroachment-free shallow trenches, and planarized field oxide. The process offers poly silicon-filled deep trenches. The process also relies on noncritical lithography and novel etch processes to planarize the deposited poly-silicon from the top of the active areas, and oxidation to consume the poly-silicon in the field regions. Electrical results are presented proving the viability of the isolation scheme     

Static and free vibration analysis of variable-depth bridges of arbitrary alignments using the isoparametric spline finite strip method

The isoparametric spline finite strips for shells are employed to solve static and free vibration problems of variable-depth bridges of arbitrary alignments. Using this approach, a continuous bridge is first split up into substructures. Each substructure is modelled as an assemblage of isoparametric spline finite strips. Compatibility between substructures is ensured by suitable transformation at the interface. The presence of support diaphragms and bearings can also be accounted for. This method retains the computational efficiency of the spline finite strip method while it is much more flexible in geometric modelling. Solutions of this method are compared with other available solutions, and good agreement is observed.