Techno-economic study of different alternatives for biodiesel production

Biodiesel has become an attractive diesel fuel substitute due to its environmental benefits since it can be made from renewable resource. However, the high costs surrounding biodiesel production remains the main problem in making it competitive in the fuel market either as a blend or as a neat fuel. More than 80% of the production cost is associated with the feedstock itself and consequently, efforts are focused on developing technologies capable of using lower-cost feedstocks, such as recycled cooking oils and wastes from animal or vegetable oil processing operations.     

Thermal solution of Kashpir shale in pressurized benzene under supercritical conditions

The results of the thermal solution of oil shale in benzene in a flow unit under supercritical conditions are reported. It was found that the conversion of shale organic matter into liquid products increased by a factor of 2.5 with an increase in the solvent pressure from 5 to 15 MPa.     

Sp3/sp2 character of the carbon and hydrogen configuration in micro- and nanocrystalline diamond

Hot filament and microwave plasma CVD micro- nanocrystalline diamond films are analysed by visible and ultra-violet excitation source Raman spectroscopy. The sample grain size varies from 20 nm to 2 μm. The hydrogen concentration in samples is measured by SIMS and compared to the grain size, and to the ratio of sp² carbon bonds determined by Raman spectroscopy from the 1332 cm^− 1 diamond peak and the sp² 1550 cm^− 1 G band. Hydrogen concentration appears to be proportional to the sp² bonds ratio. The 3000 cm^− 1 CH_x stretching mode band intensity observed on the Raman spectra is decreasing with the G band intensity. Thermal annealing modifies the sp² phase structure and concentration, as hydrogen outdiffuses.     

A rubber-modified thermoplastic where the morphology produced by phase-separation induced by polymerization disappears at high conversions

An unexpected experimental finding is reported where the primary morphology developed during polymerization-induced phase separation in a rubber-modified thermoplastic practically disappears at high conversions. This process was evidenced by light scattering (LS) and scanning electron microscopy (SEM) for a particular composition of solutions of polyisobutylene oligomers (PIB) in isobornylmethacrylate (IBoMA), during the free-radical polymerization of the monomer. The primary phase separation produced a dispersion of domains rich in PIB containing significant amounts of the monomer (IBoMA). Polymerization of the monomer in these domains occurred at high overall conversions producing the filling of dispersed domains with a PIBoMA-PIB blend that could not be distinguished from the matrix. Under these conditions the final material had the appearance of a homogeneous blend.     

Choosing the technology of combined processing of titanium-rare-metal raw materials

The main rules and principles which govern the choice of new variants for chemical technology of combined processing of titanium-rare-metal raw materials are considered. The existing variants of the technology are characterized from the viewpoint of their technological, economical, and ecological efficiency and social importance for a given region. A realistic choice of a technology from a large number of available variants should take into account the entire combination of their advantages and disadvantages The implementation of a rational technological scheme will result in the creation of economically profitable and efficient domestic production satisfying the demands of Russian industry in rare-metal and titanium materials. Directions are noted in which it is expedient to continue studies on designing a rational technology of loparite concentrate or some other concentrate.     

A small-angle X-ray scattering study of powder compaction

This work demonstrated a novel and potentially important application of two-dimensional small-angle X-ray scattering (2D-SAXS) to investigate powder compaction. SAXS from powder compacts of three materials commonly used for pharmaceutical tabletting exhibited azimuthal variations, with stronger intensity in the direction of the applied compaction force, relative to the transverse direction. This implied that compaction of a (macroscopic) powder could also produce changes on the molecular (nanometre) scale, which can be probed by 2D-SAXS. Two possible explanations for this effect were suggested. A combination of anisometric (i.e. elongated or flattened) granules with anisotropic morphologies could result in azimuthal variation in X-ray scattering due to granule orientation. It is expected that this mechanism would require relatively low packing density, so may operate during die filling. Granule re-orientation appeared less likely at higher packing densities and compaction pressures, however. Under these conditions, the changes in the 2D-SAXS patterns would be consistent with the powder granules becoming relatively flattened in the compression direction, with corresponding changes in their nano-scale morphology. The magnitude of this effect was found to vary between the materials used and increased with compaction pressure. This suggested that 2D-SAXS studies could provide useful information on force-transmission within a compressed powder. Further analysis of the data also suggested differences in the compaction mechanisms (i.e. granule re-orientation, deformation or fragmentation) between the materials studied.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

Sprinklered office fire tests

This paper presents data relating to the performance of sprinklers and detectors in real office fire situations. For sprinklers, these data are additional to that associated with the standardized testing used to determine the design delivery density and pressure requirements for various occupancy situations, and provide a useful insight into the effect of sprinklers on developing fires with various office situations. The data given in this paper include the times for activation of various types of sprinkler heads (normal and fast response), the efficacy of the systems as far as extinguishment is concerned, estimates of the maximum size of the fires prior to commencement of extinguishment and associated air temperatures at various locations within the office enclosures. Copyright © 2008 John Wiley & Sons, Ltd.