如何掌握印刷压力

<正> 一、印刷压力的概念与作用 印刷的过程,从某种意义上讲,是解决油墨与纸张之间矛盾的过程。要将印版上图文处的油墨转移到承印物上,就必须施加一定的力,即所谓的印刷压力。它在印刷中具有重要的作用。 1.保证粗糙的印刷面完全接触 纸张、橡皮布、印版的表面均成粗糙微孔状。对这些粗糙表面,必须在一定的压力作用下,使其受     

PEG20000中试放大的工艺研究

在一定温度和催化剂作用下 ,分别利用本体聚合和溶剂聚合的方法 ,在 1L、10 0L不锈钢高压反应釜中合成了相对分子质量为 2 0 0 0 0的聚乙二醇 ,并讨论了聚合反应机理 ,研究了催化剂用量、反应温度、反应时间对聚合反应的影响。经过红外、核磁共振、凝胶色谱、化学分析等方法对产物进行了表征。     

Preparation and Application of Active Composite Antibacterial Material Containing Ag~ and Zn~(2 )

1Introduction Harmfulbacteriaexistanywhereintheworldsuchas soil,air,water,surfacesofobjectsandourskins,etc.Thenumberofbacteriumisenormous,withmanydiffer entspecies.Theyhavethreatenedthehealthofhuman beingsseriously.Withthedevelopmentofeconomyand environme…     

宝钢2号高炉4号热风炉凉炉实践

对宝钢2号高炉4号热风炉凉炉的原因、凉炉的前期族备工作、凉炉的设备和方法以及凉炉的实际效果进行了总结。通过这次凉炉实践，取得了一些有价值的经验，这些经验对今后宝钢砖硅热风炉的凉炉具有重要的参考意义。     

微波-表面活性剂协同提取万寿菊叶黄素工艺研究

以提高万寿菊叶黄素的提取率为目的,采用单因数实验结合正交实验的方法.研究了微波-表面活性剂协同提取万寿菊花中叶黄素的丁艺.结果表明:万寿菊叶黄素的微波-表面活性剂协同提取最优工艺为:以乙酸乙酯为提取剂,表面活性剂Tween-20为最佳助萃取剂(质量分数为0.03%),提取固液比1∶60(g/mL),微波功率400 W,微波提取温度为60℃,提取时间2 min.在此工艺下,万寿菊叶黄素的提取量为3.209 mg/g.     

一次盐水设备运行总结

介绍了内蒙古海吉氯碱化工股份有限公司6万t/a离子膜烧碱装置一次盐水设备的运行情况和运行过程中存在的问题及相应的技改措施.     

催化裂化汽油选择性加氢脱硫催化剂RSDS-1的开发

介绍了用于催化裂化汽油选择性加氢脱硫催化剂RSDS-1的研究开发，考察了载体、活性组元、金属原子比以及助剂对催化剂选择性的影响。研究结果表明，催化裂化汽油中烯烃的加氢饱和受扩散限制；Co—Mo组合对烯烃饱和的能力相对较弱；较高的Co／Mo原子比有利于提高催化剂选择性；助剂的加入对催化剂选择性有明显的影响；RSDS—1催化剂用于催化裂化汽油选择性脱硫，对不同原料油适应性好，脱硫率可达80％，RON损失小于2个单位，且可长周期稳定运转。     

锂离子电池有机电解液成膜添加剂的研究现状

文章综述了锂离子电池有机电解液成膜添加剂的作用原理，具体介绍了CO2、SO2、VC化合物、卤化物、有机铜盐以及马来酐等添加剂的研究现状。     

A new iterative order reduction (IOR) method for eigensolutions of large structures

Order reduction is a computationally efficient method to estimate some lowest eigenvalues and the corresponding eigenvectors of large structural systems by reducing the order of the original model to a smaller one. But its accuracy is limited to a small range of frequencies that depends on the selection of the retained degrees of freedom. This paper proposes a new iterative order reduction (IOR) technique to obtain accurately the eigensolutions of large structural systems. The technique retains all the inertia terms associated with the removed degrees of freedom. This hence leads to the reduced mass matrix being in an iterated form and the reduced stiffness matrix constant. From these mass and stiffness matrices, the eigensolutions of the reduced system can be obtained iteratively. On convergence the reduced system reproduces the eigensolutions of the original structure. A proof of the convergence property is also presented. Applications of the method to a practical GARTEUR structure as well as a plate have demonstrated that the proposed method is comparable to the commonly used Subspace Iteration method in terms of numerical accuracy. Moreover, it has been found that the proposed method is computationally more efficient than the Subspace Iteration method. Copyright © 2003 John Wiley & Sons, Ltd.