适度出砂技术在海上稠油油田的应用研究

通过理论计算和室内出砂模拟实验,分别从地层出砂、井筒附近防砂以及井筒内的携砂生产三方面时适度出砂开采方式进行了研究.结果表明:地层出砂对储层物性有所改善,不同粒径段颗粒出砂1%后,渗透率增幅为20%左右,其中细微砂粒(<39 μm)的产出对渗透率提高贡献最大,为21,07%-37.60%;防砂管和地层环空间砂粒的堆积对产能影响很大,环空无砂时产能提高1.71倍,但当环空充满砂时产能仅提高14.70%;只有当井筒内的流体流速大于等于砂粒的沉降末速时产出砂才能被携带出井筒.该开采方式在渤海稠油油田得到成功应用.     

Zonal disintegration phenomenon in enclosing rock mass surrounding deep tunnels -- Elasto-plastic analysis of stress field of enclosing rock mass

The zonal disintegration phenomenon (ZDP) is a typical phenomenon in deep block rock masses. In order to investigate the mechanism of ZDP, an improved non-linear Hock-Brown strength criterion and a bi-linear constitutive model of rock mass were used to analyze the elasto-plastic stress field of the enclosing rock mass around a deep round tunnel. The radius of the plastic region and stress of the enclosing rock mass were obtained by introducing dimensionless parameters of radial distance. The results show that tunneling in deep rock mass causes a maximum stress zone to appear in the vicinity of the boundary of the elastic and the plas-tic zone in the surrounding rock mass. Under the compression of a large tangential force and a small radial force, the rock mass in the maximum stress zone was in an approximate uniaxial loading state, which could lead to a split failure in the rock mass.     

大变幅扬程多机组泵站并联运行水泵性能分析

分析了大变幅扬程下灌溉泵站并联运行水泵机组性能,提出了提高泵站装置效率的方法。     

Highly ion-conductive solid polymer electrolytes based on polyethylene non-woven matrix

Highly ion-conductive solid polymer electrolyte (SPE) based on polyethylene (PE) non-woven matrix is prepared by filling poly(ethylene glycol) (PEG)-based crosslinked electrolyte inside the pores of the non-woven matrix. The PE non-woven matrix not only shows good mechanical strength for SPE to be a free-standing film, but also has very porous structure for high ion conductivity. The ion conductivity of SPE based on PE non-woven matrix can be enhanced by adding sufficient non-volatile plasticizer such as poly(ethylene glycol) dimethyl ether (PEGDME) into ion conduction phase without sacrificing mechanical strength. SPE with 20 wt.% crosslinking agent and 80 wt.% non-volatile plasticizer shows 3.1 × 10⁻⁴ S cm⁻¹ at room temperature (20 °C), to our knowledge, which is the highest level for SPEs. It is also electrochemically stable up to 5.2 V and has high transference number about 0.52 due to the introduction of anion receptor as an additive. The interfacial resistance between Li electrode and SPE is low enough to perform charge/discharge test of unit cell consisting of LiCoO₂/SPE/Li at room temperature. The discharge capacity of the unit cell shows 87% of theoretical value with 86% Coulombic efficiency.     

Effects of silicone oil and polymeric modifiers on the mechanical properties of highly filled LLDPE

The effects of coupling agents, silicone oil, and three types of polymeric modifiers on the mechanical properties of linear low density polyethylene (LLDPE) composites highly filled with aluminium hydroxide [Al(OH)₃] were studied. Polymeric modifiers that contain polar groups, such as silane‐grafted polyethylene (Si‐g‐PE) and acrylic‐acid‐grafted ethylene‐vinyl acetate copolymer (AA‐g‐EVA), improve the mechanical properties dramatically, while nonpolar modifiers improve them to some extent. When Al(OH)₃ was treated using a titanate coupling agent, the silicone oil increased the impact strength and elongation at break of the LLDPE/Al(OH)₃ composites. Introduction of a polymeric modifier containing polar groups destroys the beneficial effects of silicone oil on film mechanical properties, while the introduction of a nonpolar elastomeric polymeric modifier retains the high impact strength and elongation at break. SEM analyses provide the indirect evidence of the encapsulation of silicone oil around the filler. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 121–128, 2002     

Study of UAV tracking based on CNN in noisy environment

Multimedia Tools and Applications - Recently, there are lots of tracking methods proposed to improve the performance of visual tracking in videos with challenging situations, such as background...     

Robust Control of Networked System and Its Application

International Journal of Control, Automation and Systems - In this paper, the stability issue of networked system with dynamical topology in intelligent vehicle is studied. The systems are...     

基于Kanai-Tajimi模型的地震作用荷载新型识别方法

目的研究一种识别地震作用荷载的方法,为地震作用荷载的识别与相应结构的动力特性、损伤的识别提供一种新的途径,进一步为结构的安全性、损伤进程和耐久性等研究提供理论参考.方法利用Kanai-Tajimi模型将单位强度白噪声过程模拟为未知的地震作用,并将其作用在结构上,然后根据数值模拟计算得到的结构体系响应作为观测量,采用Kalman滤波对未知荷载状态加以识别.结果最终可以利用结构的加速度响应反演得出地震作用的等效荷载,在人工添加5%观测噪声的条件下,最大误差率为7%左右,而在人工添加10%观测噪声的条件下,最大误差率为8%左右.结论通过算例的验证,说明笔者所采用的方法精度较高,获得了较好的识别效果.     

Dynamic buffering performance of the honeycomb paperboard filled with polyurethane

A new kind of composite buffering material was made by filling the voids of honeycomb paperboard with polyurethane. Drop tests were performed to evaluate the dynamic energy absorption capacity of the material. Based on the tests results, we analyzed the mechanical behaviors of the material under different conditions and obtained the inherent influencing laws of some factors on the material＇s dynamic buffering performance. It was shown that the dynamic buffering performance varied directly with impact velocity, and inversely with the void diameter, thickness and buffeting area of the composite material.