Research and application of automatic control system of argon blowing at ladle shroud

Argon blowing at the ladle shroud requires the best flow control strategy to effectively avoid the secondary oxidation of molten steel, slag entrapment and heat loss during the casting of the tundish, and at the same time, give full play to the role of bubbles to remove inclusions. Therefore, an automatic control system for argon blowing at the ladle shroud was proposed. The data collected by S7-300PLC and software programming were used to adjust the argon blowing flow online in real time according to factors such as pouring and continuous pouring. On this basis, PID control algorithm and closed loop control mechanism were used for real time adjustment. The flow control valve ensures theminimum deviation between the actual value of the flow and the set value. The production data of this system in the first quarter of 2021 in a special steel plant show that the proportion of furnaces with an acid soluble aluminum (Als) loss percentage of less than 10% of each steel grade has increased by 5.52%, and the proportion of furnaces with an Als loss percentage of more than 60% has increased from 1% decrease to 0. The actual application results show that the use of the system improves the surface quality of the continuous casting slab and the performance of the final product.     

Achieving fast and bandwidth-efficient shared-path protection

Dynamic provisioning of restorable bandwidth guaranteed paths is a challenge in the design of broad-band transport networks, especially next-generation optical networks. A common approach is called (failure-independent) path protection, whereby for every mission-critical active path to be established, a link (or node) disjoint backup path (BP) is also established. To optimize network resource utilization, shared path protection should be adopted, which often allows a new BP to share the bandwidth allocated to some existing BPs. However, it usually leads the backup paths to use too many links, with zero cost in term of additional backup bandwidth, along its route. It will violate the restoration time guarantee. In this paper, we propose novel integer linear programming (ILP) formulations by introducing two parameters (/spl epsi/ and /spl mu/) in both the sharing with complete information (SCI) scheme and the distributed partial information management (DPIM) scheme. Our results show that the proposed ILP formulations can not only improve the network resource utilization effectively, but also keep the BPs as short as possible.     

Rheology in Processing of in Situ Composites of Polypropylene and Low Melting Poing Metals

The low melting point metallic tin powder or alloy of tin and lead was blended with polypropy-lene. A kind of in situ composite has been prepared. The variations of torque were studied when the composites were mixed in Haake torque rheogeniometer. By way of capillary extrusion, effects upon rheology of the in situ com-posites of the low melting point metals (LMPM) and coupling agent for their different variety and content, were investigated. From flow curves, the results indicate that in situ composites mixed with the LMPM are a kind of pseudoplastic fluid. If the LMPM were melted, the higher the content of the LMPM , the lower apparent viscosity of composites. Meanwhile, when the coupling agent is added into composites, the viscosity of composite will go up first and drop then. This shows that the LMPM have a promoter flow action on the polypropylene.     

同位素稀释质谱法测定高放废液中的铀

用双同位素稀释质谱法测定高放废液中的微量铀,采用TBP/Kel-F粉反相分配色层法分离铀,双稀释剂分别为浓缩~(235)U及~(238)U,铀同位素丰度比的质谱测定相对标准误差优于0.1%,化学处理及质谱测定全流程铀的空白值为3×10~(-9)g,方法检测限对于铀为1×10~(-9)g,高放废液中微量铀测定结果不确定度为±2%。     

分形方法用于有噪图像边缘检测的研究

本文研究了加性高斯白噪声对于基于离散分数布朗随机场模型图像分形维数估计的影响，并将分形方法用于图像边缘检测，指出在加性高斯白噪声的情况下，分形方法用于图像边缘检测较之经典的基于梯度运算的边缘检测方法有好的抗噪性能，同时又能检测比较丰富的图像边缘细节。     

椭球反射镜膜厚均匀性

本文分析了椭球反射镜膜层厚度均匀性对反射率的影响,从理论上得到膜厚计算公式。根据计算的膜厚分布设计了遮蔽板,获得较好的反射特性。     

底敞口充气浮箱研究和试验

提出底敞口充气浮箱的结构和概念。经模型模拟试验研究分析，经典浮力定律可用于这种浮箱的浮力计算；其动充气状况还具有一定的允许伤损面积。它的研究将为水陆两用车辆增大浮力，缩小外形，提高水上自下而上能力和潜驶潜伏提供具有诱惑力的工程应用前景。     

准分子激光器异步感应密封传动技术

一种新型准分子激光器循环系统中的密封传动技术，具有可耐高气压，不失耦，不使用昂贵强磁材料，结构简单等优点，虽有涡流损失过大之不足，但能很好地适用于小功率下运行。     

核电厂放射性监测系统仿真的数学物理模型

较详细地介绍了在北京核电厂模拟培训中心的模拟器上建立ＲＭＳ仿真系统的工作。首先对仿真的原型进行分析和简化，建立数学物理模型，并对包括ＲＣＳ、ＰＺＲ、ＳＧ、ＣＶＣＳ等的近２０个核电厂系统进行了动态仿真建模，确定ＲＭＳ各监测点放射性水平仿真读数的计算方法，最后，给出部分仿真实验结果，以验证数学物理模型的可靠性和适用性。