Reactive Commercial Ni/Al Nanolayers for Joining Lightweight Alloys

Reactive nanoscale multilayer foils for use in joining techniques have attracted a great deal of attention. A common feature of these nanolayers is the large amount of heat released during the reaction between the layers to form a new phase. In this study, films of alternated Ni and Al nanolayers (NanoFoil^® made by the Indium Corporation) with period (bilayer thickness) close to 54 nm and with a thickness of 60 μm were used as local heat sources to bond lightweight alloys. The as-deposited Ni and Al alternated nanolayers evolve into NiAl nanometric grains when the multilayer, ignited by an electrical discharge, reacts. Joining of lightweight alloys was performed at room temperature under pressures of 10-80 MPa. The ability of the nanolayers to join these alloys by high temperature diffusion bonding was also investigated. The microstructural and chemical characterizations of the interfaces were performed on cross-sections of the joints by scanning electron microscopy and energy dispersive x-ray spectroscopy. Ni/Al nanolayers are an effective means of joining titanium alloys at room temperature. A sound interface, mainly composed by NiAl grains, is obtained in joints of TiAl/TiAl and TiAl/Inconel, produced with NanoFoil^® by annealing at 700 ºC, during 60 min under a pressure of 10 MPa. The low shear strength revealed a weak adhesion of the nanofoil to the base materials.     

Effect of self-etching dual-curing universal adhesive system application on bond strength of dentin resinous liners dentin

Purpose: The aim of this study was to evaluate the influence of previous application of an adhesive system on bond strength of resinous liner materials to dentin. Methods: Ninety bovine incisors crowns had a 6 × 6 mm area of dentin exposed, with minimum of 2 mm thickness. They were embedded in acrylic resin, and the dentin was polished with P600 SiC sandpaper for 30 s to standardize the smear layer. The specimens were divided into 6 groups (n = 15) according to the application or not of a self-etching system (Futurabond U – Voco) and the type of resinous liner used: A+Ionoseal (adhesive and Ionoseal – Voco); Ionoseal (Ionoseal only); A+Vitrebond (adhesive and Vitrebond – 3M/ESPE); Vitrebond (Vitrebond only); A+Ionosit (adhesive and Ionosit – DMG) and Ionosit (Ionosit only). Adhesives were used following manufacturer’s instructions, and the liner materials were applied inside a 2-mm-depth matrix and light-cured for 20 s. The bond strength was measured by microtensile test, using a universal testing machine with a cross-speed of 1 mm/min. Data were analyzed using one-way ANOVA and Tukey’s test (p < 0.05). Results: The adhesive system application increased bond strength of all liners tested. Ionoseal presented the highest bond strength when the adhesive system was used and exhibited similar performance to Vitrebond without adhesive. Ionosit without adhesive showed the smallest bond strength compared with the other liners tested. Conclusion: The application of an adhesive system prior to the use of the resinous liners improved the bond strength to dentin and should be preconized.     

Cold Atmospheric Plasma Apoptotic and Oxidative Effects on MCF7 and HCC1806 Human Breast Cancer Cells

Breast cancer (BC) is a malignant neoplasia with the highest incidence and mortality rates in women worldwide. Currently, therapies include surgery, radiotherapy, and chemotherapy, including targeted therapies in some cases. However, treatments are often associated with serious adverse effects. Looking for new options in BC treatment, we evaluated the therapeutic potential of cold atmospheric plasma (CAP) in two cell lines (MCF7 and HCC1806) with distinct histological features. Apoptosis seemed to be the most prevalent type of death, as corroborated by several biochemical features, including phosphatidylserine exposure, the disruption of mitochondrial membrane potential, an increase in BAX/BCL2 ratio and procaspase 3 loss. Moreover, the accumulation of cells in the G2/M phase of the cell cycle points to the loss of replication ability and decreased survival. Despite reported toxic concentrations of peroxides in culture media exposed to plasma, intracellular peroxide concentration was overall decreased accompanying a reduction in GSH levels shortly after plasma exposure in both cell lines. In HCC1806, elevated nitric oxide (NO) concentration accompanied by reduced superoxide levels suggests that these cells are capable of converting plasma-derived nitrites into NO that competes with superoxide dismutase (SOD) for superoxide to form peroxinitrite. The concomitant inhibition of the antioxidative activity of cells during CAP treatment, particularly the inhibition of cytochrome c oxidase with sodium azide, synergistically increased plasma toxicity. Thus, this in vitro research enlightens the therapeutic potential of CAP in the treatment of breast cancer, elucidating its possible mechanisms of action.     

β-Cyclodextrin Inclusion Complex to Improve Physicochemical Properties of Pipemidic Acid: Characterization and Bioactivity Evaluation

The aptitude of cyclodextrins (CDs) to form host-guest complexes has prompted an increase in the development of new drug formulations. In this study, the inclusion complexes of pipemidic acid (HPPA), a therapeutic agent for urinary tract infections, with native β-CD were prepared in solid state by kneading method and confirmed by FT-IR and ¹H NMR. The inclusion complex formation was also characterized in aqueous solution at different pH via UV-Vis titration and phase solubility studies obtaining the stability constant. The 1:1 stoichiometry was established by a Job plot and the inclusion mechanism was clarified using docking experiments. Finally, the antibacterial activity of HPPA and its inclusion complex was tested on P. aeruginosa, E. coli and S. aureus to determine the respective EC_50s and EC_90s. The results showed that the antibacterial activity of HPPA:β-CD against E. coli and S. aureus is higher than that of HPPA. Furthermore, HPPA and HPPA:β-CD, tested on human hepatoblastoma HepG2 and MCF-7 cell lines by MTT assay, exhibited, for the first time, antitumor activities, and the complex revealed a higher activity than that of HPPA. The use of β-CD allows an increase in the aqueous solubility of the drug, its bioavailability and then its bioactivity.     

Crystallization of Honey at −20°C

Honeys from different regions of the province of Buenos Aires were stored at ?20°C, and factors that affect crystallization were analyzed. Crystals were observed by light microscopy. Firmness, adhesivity and viscosity of the samples were measured. Honey was characterized by determining the water activity, turbidity, moisture, fructose, and glucose contents. Results show that the viscous characteristics of the samples depend on the number, size, and disposition of crystals. Various honey samples exhibited Newtonian, pseudoplastic, and thixotropic behaviors. Crystallization was favored at higher moisture contents, suggesting that the parameters that affect honey crystallization at room temperature have a different effect at freezing temperatures. Honey that presented higher values of firmness had a moisture content lower than 17%, and a linear inverse relationship was observed between the adhesivity and firmness of honey samples.     

An integrated project of entrepreneurship and innovation in engineering education

This paper presents a new line of project based learning in the School of Engineering of University of Minho: the Innovation and Entrepreneurship Integrated Project (IEIP). Four groups, each one composed of students from different engineering integrated master courses – Mechanical, Industrial Electronics and Computers, Polymer, Industrial Management – compete against each other in developing or improving commercial products manufactured by actual industries. There have been so far five editions of the IEIP, with five different companies and five diverse products, however, all these products included components that required knowledge from all the engineering courses involved. Only with the cooperation between the students of the various courses that compose each multidisciplinary team, the success is attainable. As each student has to deal with various engineering scopes, students’ technical skills are greatly enlarged and they acquire a multidisciplinary knowledge that was not possible in another way. Their soft skills like project management, teamwork, communication ability and personal development, which are valuable requisites for their future employers, are also improved. The participating industries also take advantage of the project: the groups competing against each other act as a multiskilled work force, actually making proposals capable of improving their products, their efficiency, and reducing costs.     

Simulation and modeling: simulating optical interconnects

The computer-aided design tool can be used in choosing design parameter values that help lower the cost and increase reliability. Good tools are also necessary to minimize the length of the design cycle to bring products to market in a timely manner. Some tools exist that can be used for simulating and designing optical interconnects, but they are intended for electronics and are used for lack of tools more suitable for their unique needs. Currently, no computer-aided design tools encompass all the simulation methodologies required to address the design needs of optical interconnects. After reviewing briefly the various CAD tools that are available, the authors discuss in more detail two tools developed recently: iSMILE (illinois Simulator for the Modeling of Integrated-circuit Level Elements), a CAD tool for the rapid development and simulation of new circuit-level optoelectronics models; and iFROST (illinois FibeR-optic and Optoelectronic Systems Toolkit), a high-level simulator of digital lightwave links     

Real-time risk monitoring in business processes: A sensor-based approach

This article proposes an approach for real-time monitoring of risks in executable business process models. The approach considers risks in all phases of the business process management lifecycle, from process design, where risks are defined on top of process models, through to process diagnosis, where risks are detected during process execution. The approach has been realized via a distributed, sensor-based architecture. At design-time, sensors are defined to specify risk conditions which when fulfilled, are a likely indicator of negative process states (faults) to eventuate. Both historical and current process execution data can be used to compose such conditions. At run-time, each sensor independently notifies a sensor manager when a risk is detected. In turn, the sensor manager interacts with the monitoring component of a business process management system to prompt the results to process administrators who may take remedial actions. The proposed architecture has been implemented on top of the YAWL system, and evaluated through performance measurements and usability tests with students. The results show that risk conditions can be computed efficiently and that the approach is perceived as useful by the participants in the tests.     

An optimal decision-making approach for the management of radiotherapy patients

In this paper, novel integer programming formulations are developed for solving the optimal scheduling of patients waiting for radiotherapy treatment. In this specific clinical domain, the suitable management and control of a patients’ waiting list strongly affect both the quality of the therapeutical outcome, in terms of effectiveness, and the cost-saving use of the overall therapeutical resources, in terms of efficiency. The proposed models allow the best scheduling strategy to be devised by taking into account the quality of the health care service offered to the patient as well as the status and the preferences of the patient. The computational experiments, carried out on realistic scenarios and considering real data, are very promising and show the efficiency and robustness of the proposed models to address the problem under consideration.     

Chemical and biological variability of hot pepper fruits (Capsicum annuum var. acuminatum L.) in relation to maturity stage

The aim of the present work was to evaluate the chemical composition and the radical-scavenging and antioxidant activities of hot pepper fruits (Capsicum annuum L. var. acuminatum) at three maturity stages (small green, green and red). GC–MS analysis of n-hexane and chloroform fractions showed a different composition between the three stages of ripening. The first stage of maturation (small green) showed the highest radical-scavenging activity (IC₅₀ of 129 μg/ml). Using the bovine brain peroxidation assay, the methanolic extract of green pepper showed significant antioxidant activity (IC₅₀ of 522 μg/ml). Addition of methanolic extract of red and green pepper inhibited oxidation of linoleic acid. Methanolic extract of red pepper showed greater antioxidative potency than the others (IC₅₀ of 3 μg/ml). The different composition of lipophilic compounds and the various amount of phenolics, showed in the three stage of ripening of C. annuum var. acuminatum fruits, modifies the antioxidant activity.