Binding of tissue plasminogen activator to endothelial cells. The effect on functional properties. Localization of a ligand in the B-chain of tPA

The binding of 125I-labelled tissue plasminogen activator (tPA), the tPA A- or B-chain to endothelial cells (EC) were studied in suspensions of cultured human umbilical vein EC (HUVEC) or immortalized microvascular EC (HMEC). By determinations of the concentration-dependent binding it was shown that both the A-chain and the B-chain, which were isolated after partial reduction of two-chain tPA, contain ligands for binding to EC. The affinity for the B-chain was much higher than for the A-chain according to Scatchard analysis (Kd 24 and 515 nM, respectively), whereas the number of binding sites was higher for the A-chain than for the B-chain (Bmax 8 x 10(5) and 1.2 x 10(5), respectively). There were no cross interactions between the A- and B-chains and their binding sites. The binding of tPA to EC induced an almost 100-fold increase of the activation rate when compared to the same amount of enzyme in free solution, which in contrast to the fibrin-induced stimulation was not inhibited by antibodies against fibrin. The enzymatic activity of the B-chain was much less affected by the association to the cells. Both tPA and the tPA B-chain were largely protected against inhibition by an excess plasminogen activator type-1 (PAI-1) when bound to EC, whereas the same amount of free tPA was totally inactivated. The competition studies strongly indicated that an N-terminal segment in the B-chain, AKHRRSPGER, may be the ligand part of the B-chain. It is interesting to note that this polypeptide segment also participates in a binding site for PAI-1, necessary for effective inhibition. This implies a possible competition between PAI-1 and a tPA-receptor for binding of tPA. High molecular weight urokinase had no quenching effect on the binding of the B-chain to EC.     

Syllables as processing units in handwriting production.

This research focused on the syllable as a processing unit in handwriting. Participants wrote, in uppercase letters, words that had been visually presented. The interletter intervals provide information on the timing of motor production. In Experiment 1, French participants wrote words that shared the initial letters but had different syllable boundaries. In Experiment 2, French- and Spanish-speaking participants wrote cognates and pseudowords with a letter sequence that was always intrasyllabic in French and intersyllabic in Spanish. In Experiment 3, French-Spanish bilinguals wrote the cognates and pseudowords with the same type of sequences. In the 3 experiments, the critical interletter intervals were longer between syllables than within syllables, indicating that word syllable structure constrains motor production both in French and Spanish. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Report on the therapeutic use of rimantadine and amantadine]

A discussion is carried out about the experiences with the application of rimantadine and amantadine to patients with influenza. The basic general results consisted in the fact that 2 of the 74 patients treated had a high cure percent (> 68.0%) within the first 72 hours after using the drug. No new diseased were found among the 40 contacts to whom chemoprophylaxis was applied. There were only 3.9% adverse reactions among the total number of people treated with amantadine.     

Anodic oxidation of mecoprop herbicide at lead dioxide

The electrochemical oxidation of an aqueous solution containing mecoprop (2-(2-methyl-4-chlorophenoxy)propionic acid) has been studied at PbO₂ anodes by cyclic voltammetry and bulk electrolysis. The influence of current density, hydrodynamic conditions, temperature and pH on the degradation rate and current efficiency is reported. The results obtained show that the use of PbO₂ leads to total mineralization of mecoprop due to the production of oxidant hydroxyl radical electrogenerated from water discharge. The current efficiency for the electro-oxidation of mecoprop is enhanced by low current density, high recycle flow-rates and high temperature. In contrast, the pH effect was not significant. It has also been observed that mecoprop decay kinetics follows a pseudo-first-order reaction and the rate constant increases with rising current density.     

Nonisothermal melt-crystallization kinetics of isotactic polypropylene synthesized with a metallocene catalyst and compounded with different quantities of an α nucleator

The nonisothermal crystallization kinetics of a metallocene-made isotactic polypropylene (m-iPP) and its compounds with 0.1 wt % and 0.3 wt % of a sorbitol derivative [1,3:2,4-bis(3,4-dimethylbenzylidene)sorbitol (DMDBS); an α nucleator] were investigated by differential scanning calorimetry at different cooling rates from the melt. The nucleation efficiency was proved by a significant increase in the crystallization temperatures (accompanied by a slight augmentation of the degree of crystallinity and a decrease in the crystal sizes). This increase in the crystallization temperatures led to higher amounts of fractional content in the γ polymorph, even though DMDBS was supposed to be a nucleator for the α form. The Avrami and Ozawa methods effectively described only the early stage of crystallization, whereas a combined Avrami–Ozawa method was valid for the whole crystallization process. The values of the exponent for this method decreased for nucleated samples in the later stage of crystallization, especially in the case of m-iPP with 0.3 wt % DMDBS added (m-iPP03). The activation energy of the process and the surface free energy were also estimated. The production of considerable proportions of the γ polymorph in m-iPP03 corresponded to higher values of the activation energy and lower values of the surface free energy. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Use of postconsumer polyethylene in blends with polyamide 6: Effects of the extrusion method and the compatibilizer

Blends of polyamide and high‐density polyethylene show adequate properties for a large range of applications: they are used for the production of filaments, containers, and molding resins. The effect of the addition of 2 wt % of a compatibilizer, maleic anhydride grafted polyethylene, to the blend was studied and compared to the use of postconsumer polyethylene. The samples were extruded with single‐ and twin‐screw extruders with 25, 50, or 75 wt % f polyethylene, and the test specimens, molded by injection, were characterized by stress–strain tests, thermal properties, and morphologies. Processing the blends with postconsumer polyethylene in both extruders improved the mechanical properties in comparison to the blends processed with high‐density polyethylene and the compatibilizer. The morphologies of these blends showed that there was a decrease in the domain size of the disperse phase with the use of the compatibilizer or postconsumer polyethylene. The results indicate that for this blend, postconsumer polyethylene substituted, with advantages, for the necessity of a compatibilizer and the use of the high‐density polyethylene. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.