PbS/CdS/ZnS Quantum Dots: A Multifunctional Platform for In Vivo Near‐Infrared Low‐Dose Fluorescence Imaging

Over the past decade, near‐infrared (NIR)‐emitting nanoparticles have increasingly been investigated in biomedical research for use as fluorescent imaging probes. Here, high‐quality water‐dispersible core/shell/shell PbS/CdS/ZnS quantum dots (hereafter QDs) as NIR imaging probes fabricated through a rapid, cost‐effective microwave‐assisted cation exchange procedure are reported. These QDs have proven to be water dispersible, stable, and are expected to be nontoxic, resulting from the growth of an outer ZnS shell and the simultaneous surface functionalization with mercaptopropionic acid ligands. Care is taken to design the emission wavelength of the QDs probe lying within the second biological window (1000–1350 nm), which leads to higher penetration depths because of the low extinction coefficient of biological tissues in this spectral range. Furthermore, their intense fluorescence emission enables to follow the real‐time evolution of QD biodistribution among different organs of living mice, after low‐dose intravenous administration. In this paper, QD platform has proven to be capable (ex vivo and in vitro) of high‐resolution thermal sensing in the physiological temperature range. The investigation, together with the lack of noticeable toxicity from these PbS/CdS/ZnS QDs after preliminary studies, paves the way for their use as outstanding multifunctional probes both for in vitro and in vivo applications in biomedicine.     

Common-Mode Response Overlapping vs. Shaping in Rail-to-Rail Op-Amp Input Stages

In this paper, a circuit technique—common-mode (CM) response overlapping—for maintaining the small-signal behavior of rail-to-rail amplifiers nearly constant over the whole input CM range, is introduced. This technique modifies the CM response of the rail-to-rail input stage adequately by means of two constant input floating voltage sources, which are adjusted by using a static tuning section. Its performance is compared with a second technique—CM response shaping—, which is also based on two variable input floating voltage sources, but relies on a dynamic feedback tuning loop. Experimental results obtained from two 3-V 0.8-m CMOS single-stage rail-to-rail amplifiers, which operate with CM response overlapping and shaping, respectively, are provided.     

Dry Processing and Recycling of Thick Nacre–Mimetic Nanocomposites

Bioinspired nanocomposites with high levels of reinforcement hold great promise for future, green lightweight, and functional engineering materials, but they suffer from slow, tedious, and nonscalable preparation routes, that typically only lead to very thin films. A rapid and facile dry powder processing technique is introduced to generate bioinspired nanocomposite materials at high fractions of reinforcements (50 wt%) and with millimeter scale thickness. The process uses powder drying of vitrimer-coated nanoplatelets (nanoclay and MXene) from aqueous solution and subsequent hot-pressing. As a method of choice in industrial lightweight composite materials engineering, hot-pressing underscores a high potential to translate this approach to actual products. The use of the vitrimer chemistry with temperature-activated bond shuffling is important to facilitate smooth integration into the nanocomposite design, leading to layered nacre-inspired nanocomposites with nanoscale hard/soft order traced by X-ray diffraction and excellent mechanical properties investigated using flexural tests. Recycling by grinding and hot-pressing is possible without property loss. The compatibility with existing composite processing techniques, scalable thickness and dimensions, and recyclability open considerable opportunities for translating bioinspired nanocomposites to real-life applications.     

Intratumoral Thermal Reading During Photo‐Thermal Therapy by Multifunctional Fluorescent Nanoparticles

The tremendous development of nanotechnology is bringing us closer to the dream of clinical application of nanoparticles in photothermal therapies of tumors. This requires the use of specific nanoparticles that must be highly biocompatible, efficient light‐to‐heat converters and fluorescent markers. Temperature reading by the heating nanoparticles during therapy appears of paramount importance to keep at a minimum the collateral damage that could arise from undesirable excessive heating. In this work, this thermally controlled therapy is possible by using Nd³⁺ ion‐doped LaF₃ nanocrystals. Because of the particular optical features of Nd³⁺ ions at high doping concentrations, these nanoparticles are capable of in vivo photothermal heating, fluorescent tumor localization and intratumoral thermal sensing. The successful photothermal therapy experiments here presented highlight the importance of controlling therapy parameters based on intratumoral temperature measurements instead of on the traditionally used skin temperature measurements. In fact, significant differences between intratumoral and skin temperatures do exist and could lead to the appearance of excessive collateral damage. These results open a new avenue for the real application of nano­particle‐based photothermal therapy at clinical level.     

Fully digital BPSK demodulator for satellite supressed carrier telecommand system

In this paper, we present the design of a fully digital binary phase shift keying demodulator for application in satellite high‐rate suppressed carrier telecommand system. The proposed system digitalizes the received signal in the intermediate frequency stage using bandpass sampling technique, and the resulting baseband signal is used to synchronization of symbol and phase and to bit detection. The design of all functional modules is presented in details. Another innovation presented in this work is the inclusion of a non‐linearity in the phase synchronizer module to permit its operation independent from the signal amplitude. Moreover, aiming the characterization and performance evaluation of the system, we do some original mathematical analyses. Finally, test results show that the demodulator complies all the project requirements, and the prototype implementation loss, in terms of bit energy to noise power density ratio, is less than 0.3 dB. Copyright © 2016 John Wiley & Sons, Ltd.     

RPSF: a new QoS bandwidth request mechanism for the IEEE?802.16

The IEEE 802.16 standard is a Broadband Wireless Access (BWA) technology which offers Quality of Service (QoS) support to different types of applications. This standard defines the physical (PHY) and medium access control (MAC) layers. Its MAC layer defines different types of QoS mechanisms to support various types of applications, being the multicast polling one of these mechanisms. Under this mechanism, based on a contention process, every connection competes to gain access to the channel in order to place its bandwidth requests. In this paper, we propose a new signalling mechanism, called Requests Per Service Flow (RPSF), to reduce the contention phase in the frame. Additionally, we undertake a comparison of this new method with respect to other mechanisms. The simulation results show that our new proposal outperforms other mechanisms recently reported in the literature, in terms of throughput and end-to-end delay.     

Teamwork assessment in the educational web of data: A learning analytics approach towards ISO 10018

The Web of Data is an emerging research field that contributes to make better decisions because it gathers, combines and analyses different data sources available worldwide. Educational data is an interesting domain because it deals with the quality of the education itself and educational institutions which are common goals for every country. This paper is devoted to present how this idea has been used to improve a learning analytics tool. By means of this tool, teachers can perform teamwork competence assessment of a group of students taking into account how the individuals acquire the essential components of such competence. In this sense, authors use the Comprehensive Training Model of the Teamwork Competence in Engineering Domain (CTMTC) method to gather competence evidences and improve the system with a learning analytics tool to support the process. This tool is able to transform competence evidences and stores them in a competence ontology built upon ISO 10018 concepts. The final result is the production of educational results for the web of data.     

An adaptive hybrid MOOC model: Disrupting the MOOC concept in higher education

In the 18th century, the educational model underwent a disruptive change driven by the transition from an agricultural to an industrial society. In the 21st century, the change from the industrial society to a knowledge society has been consolidated, but it has not involved a disruption in the learning context. Some elements, many based on technologies, can be considered disruptive, but they have not had sufficient effect to produce a change in the model that has predominated for 300 years. In 2008, teachers began to offer training outside the walls of the university, with a totally disruptive and chaotic model compared to the traditional one; this was supported by open, informal, cooperative, connectivist, autonomous and self-guided training. Massive open online courses (MOOCs) began with cMOOCs, and most universities join the initiative, but they abandoned this disruption, ultimately offering the same courses they always had with free access for anyone, resulting in the second generation of MOOCs (xMOOCs). These MOOCs responded to a new social demand, but their characteristics and context make a formative disruption – which has not yet emerged – necessary. This paper analyses the elements of the two generations of MOOCs in order to propose a new model that does not require sophisticated technological solutions and recovers the initial disruptive sense of MOOCs, so called ahMOOC. It also presents a case study that integrates the social advantages of cMOOCs, the organisational benefits of xMOOCs and the personalisation of the learning, which is essential due to the heterogeneity of the participants. The results and the participant viewpoints emerging from the case study confirm the feasibility of the model, the improvement of the results of current MOOCs and the need – demanded by the participants – to consider diversity, all of which should be accomplished in a disruptive way.     

A rolling horizon simulation approach for managing demand with lead time variability

This paper proposes a rolling horizon (RH) approach to deal with management problems under dynamic demand in planning horizons with variable lead times using system dynamics (SD) simulation. Thus, the nature of dynamic RH solutions entails no inconveniences to contemplate planning horizons with unpredictable demands. This is mainly because information is periodically updated and replanning is done in time. Therefore, inventory and logistic costs may be lower. For the first time, an RH is applied for demand management with variable lead times along with SD simulation models, which allowed the use of lot-sizing techniques to be evaluated (Wagner-Whitin and Silver-Meal). The basic scenario is based on a real-world example from an automotive single-level SC composed of a first-tier supplier and a car assembler that contemplates uncertain demands while planning the RH and 216 subscenarios by modifying constant and variable lead times, holding costs and order costs, combined with lot-sizing techniques. Twenty-eight more replications comprising 504 new subscenarios with variable lead times are generated to represent a relative variation coefficient of the initial demand. We conclude that our RH simulation approach, along with lot-sizing techniques, can generate more sustainable planning results in total costs, fill rates and bullwhip effect terms.