Semiempirical,squeeze flow,and intermolecular diffusion model. II. Model verification using laser microwelding

This article reviews the application of a coupled squeeze flow and intermolecular diffusion model, which was used to predict the quality and size of microwelds in plastics. Weld widths predictions were compared with previously presented experimental results using moving heat source models and temperature fields. The motivation for this work was to develop and verify a model based on fundamental principles that could accurately predict weld size and strength for conventional plastic welding techniques as well as novel techniques such as laser microwelding. It is envisioned that the resulting model could be used to predict proper welding parameters, including laser power and travel speed, to produce welds of varying size. Although insight into weld quality can be derived from this model, it was not the goal of this work to accurately predict weld strength for laser microwelding because of the difficulty in measuring weld strength on the micron scale. However, as reported in Part 1, weld strength for impulse welds were accurately predicted. In this model it was found that variable temperature histories, rather than a single value of maximum weld temperature, allows more accurate modeling of the welding process. In this work (Part 2), microwelds as small as 11 μm in width were produced with transmission infrared welding. In addition, welds over 150‐μm wide were also generated and the model was able to predict the range of weld widths that were found experimentally. It was found that the predictions were in very good agreement with the experimental results. There was some deviation between the experimental data and the model at the extreme parameters and it is believed that this was due to the temperature‐dependent material properties as well as optical aberrations. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

An experiment for showing some kind of artificial understanding

In this paper we design an experiment which can be depicted as a simple scenario, a very limited 'world'. In this world, there are an actor that can pursue a project and an observer that is keeping its eyes on the actor. We try to show in the experiment that the observer can to some degree understand the actor based on its knowledge and some metaphors, i.e. understand what the actor is doing and why. As the conclusion of this experiment, we try to show some features of 'understanding'. These are (1) that 'understanding' has to be based on some preliminary knowledge; (2) that 'understanding' is a process of incremental learning; (3) that, as for symbolic systems, some metaphors are necessary for mapping real entities into concepts in mind.     

Standing on Solid Ground

The new Editor in Chief of IEEE Micro introduces himself and the first issue of 2007. He thanks outgoing Editor in Chief Pradip Bose for his outstanding work on Micro during his tenure. He assesses the current state of the microarchitecture field, speculates on the future, and asks readers for their suggestions on topics the magazine should cover in coming issues.     

Bioavailability and Toxicity of Metal Nutrients during Anaerobic Digestion

This paper investigates the effect of chelating agents on the bioavailability of Fe and Cu during anaerobic digestion. The results on metal speciation and methane production in anaerobic serum bottles showed that biomass was able to grow in the presence of citrate 1?mM and nitrilotriacetic acid (NTA) 1?mM, suggesting that the binding sites at the cell surface competed efficiently for the metals with the chelating agents added. The presence of free ethylenediaminetetraacetic acid 1?mM inhibited methanogenesis, and this seemed to be related to a loss in metal uptake capacity. Although the addition of soluble microbial products (SMP) did not change metal distribution in anaerobic systems, it caused an increase in the rate of methane production, and it is believed that direct uptake of Cu-SMP complexes was responsible for this increase. The best protection against Cu toxicity occurred when stoichiometric amounts of NTA, which should complex and solubilize most of the Cu, was added, and it is likely that NTA prevented lethal concentrations of Cu from being adsorbed onto the cell and hence internalized.     

The MiniWiD-Coater. III. Effect of Application Temperature on the Dissolution Profile of Sustained-Release Theophylline Pellets Coated with Eudragit Rs 30 D

Theophylline pellets were coated with Eudragit RS 30 D in a miniature fluid-bed pan coater called MiniWiD developed recently. The dispersions were plasticized with varying amounts of triethyl citrate (TEC), dibutyl phthalate (DBP), and polyethylene glycol 6000 (PEG) and applied at different temperatures ranging from 25 to 45 °C. Theophylline release was tested by dissolution using the USP Apparatus 2 (paddle) in 0.1 N hydrochloric acid under sink conditions over 6 hours.

At a coating level of 4 % (0.7 mg/cm²) sustained-release profiles were obtained from dispersions plasticized with TEC or DBP. By reducing the amount of plasticizer from 20 to 10%, films with higher permeabilities were obtained. This effect was compensated by tempering the pellets at 50 deg;C for 24 hours. The coating temperature had little effect on the dissolution profiles of TEC-plasticized films and no effect on films with DBP.

Coatings plasticized with 20% PEG were applied at temperatures ranging from 25 to 45 °C. These films required a coating level of about 18 % (3.3 mg/cm²) to provide comparable sustained-release properties. In contrast to DBP and TEC, a strong influence of the coating temperature on the release rates was observed in which higher temperatures led to slower release rates. This behavior can be explained by the minimum film-forming temperature (MFT). Since PEG does not lower the MFT of Eudragit RS 30 D, the application of these films below the MFT of 45 °C is associated with a lower degree of film formation.     

The greenhouse effect; Impact upon and the role to be played by construction

The authors highlight several possible ways in which the construction industry could lower present emissions of the greenhouse gas, carbon dioxide. It is an excellent discussion document and is recommended reading.     

Advancing controlled release packaging through smart blending

Researchers from Rutgers University and Clemson University have collaborated to develop a concept of using smart blending to generate functional packaging films for the controlled release of active compounds such as antimicrobials, antioxidants and flavour compounds to extend the shelf‐life of food. In this paper, literature results are reviewed to justify the significance of controlled release packaging (CRP) and the research gaps for further development are identified. A major research gap is the lack of packaging materials that can provide the release of active compounds at rates suitable for a wide range of food packaging applications. Smart blending is a promising technology for bridging this research gap. To fully realize the potentials of smart blending, a systematic approach for developing CRP using smart blending is also presented. Copyright © 2005 John Wiley & Sons, Ltd.     

Dicyanate semi IPNs—A new class of high performance,high temperature plastics

Dicyanate Semi-Interpenetrating Polymer Networks (semi IPNs) are made by dissolving a thermoplastic in crosslinking dicyanates and then curing the resulting mixture. The semi IPNs produced are strong, with tensile strengths of 10,000 to 12,000 psi, and flexible, with elongations to break of 10 to 17 percent. Dicyanate semi IPNs also have good thermal stability and the softening temperatures of the IPNs are significantly, higher than those of the corresponding thermoplastics.