Influence of initial growth layer and Ti underlayer on magneticproperties and recording characteristics of very thin films ofevaporated Co-Cr media

A Co-Cr film deposited directly on a substrate has an initial growth layer with low coercivity. However, the existence of a Ti underlayer prevents the formation of such a layer. As a result, Co-Cr film deposited on a Ti underlayer has high perpendicular anisotropy and coercivity even in cases of extremely thin film thickness (200 Å). As for the read-write characteristics of Co-Cr thin-film media, the existence of such an initial growth layer greatly improves the reproduced output level. The cause for this is considered to be that the free charges which appear on the back surface of the perpendicular recording layer are reduced and the demagnetization field acting on the recorded magnetization subsequently decreases due to the existence of the initial growth layer     

Effects of manufacturing defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates

The effects of defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates have been measured. The defects studied were cut fibre plies, omission of polymer films and local delamination produced by the inclusion of foreign matter. Of these it was found that only cut plies had a significant detrimental effect on the strength of a laminate. For specimens with two cut plies, the failure stress, tensile, flexural and compressive in the remaining continuous plies was the same as in the defect-free material, provided that the cut plies were widely separated. However the failure stresses were 15–18% lower in the continuous plies in the specimens containing two cut plies which were more closely spaced and in specimens containing four cut plies.     

The formation of zinc ferrite

The formation of zinc ferrite from zinc oxide and iron oxide is evaluated with high temperature X-ray diffraction experiments. Despite the problem of accurately determining the temperature of the part of the sample actually investigated, a kinetic analysis of the isothermal formation is shown to be possible. From these data the energy and entropy of activation are derived. It is further shown that neither corrections for grain growth during formation nor the presence of impurities have any influence on these results. On the other hand, the size of the reactant iron oxide particles is found to have a strong influence on both the energy and entropy of activation.     

Determination of precompression and compression force levels to minimize tablet friability using simplex

Pilot simplex experiments for improving the tablet strength of three aspirin tablet formulations based on precompression and compression forces were presented. As each simplex moved towards the direction of the optimum, the friability was being minimized and the crushing strength was concomittantly being maximized. Because it followed a systematic direction, simplex process would locate a local optimum rapidly. The appropriate levels of precompression and compression forces that produced tablets with the desired strength were attained in five trials. By contrast, random search for this force combination required at least ten trials. Simplex technique is a cost and time effective means for determining the precompression and compression forces that will reduce the friability or increase the hardness of a tablet formulation. Results appeared to also indicate that crushing strength might be a more reliable measure of tablet strength than friability.     

A finite elastostatic analysis of bimaterial interface cracks

A numerical method is developed to study the bimaterial interface problem in Neo-Hookean materials under plane stress conditions. Comparison is made with the analytical predictions for the asymptotic field of the problem. The range of dominance of the asymptotic solution at different load levels is established and the amplitudes of the crack-tip asymptotic field are related to the far field loading. The numerical model is extended to analyze the experiments conducted on specimens with an edge crack at the interface between two dissimilar Solithane plates that are characterized by Mooney-Rivlin material behavior.

---

Résumé On met au point une méthode numérique pour l'étude d'un problème d'interfaces entre deux matériaux néo-Hookiens sollicités en état plan de tension. On compare les résultats avec les prédictions analytiques étabiies pour un champ asymptotique. On établit la gamme dans laquelle la solution asymptotique est dominante, à différents niveaux de charge, et on met en relation l'ampleur du champ asymptotique à l'extrémité de la fissure avec celle du champ de contraintes à une certaine distance. Le modèle numérique est étendu à l'analyse d'essais sur éprouvettes comportant une fissure de bord à l'interface de deux tôles de Solithane caractérisée par un comportement de matériau de Mooney-Rivlin.

     

Influence of ash deposits on the heat resistance of materials for gas turbine engine blades

Leningrad. Translated from Problemy Prochnosti, No. 1, pp. 71–76, January, 1989.     

Thermomechanical behaviour of composites

This paper derives the governing equations for the thermomechanical behaviour of composites. When the basic equations for the thermoelastic behaviour of solids were first derived in the nineteenth century several approximations were made. The effect of these assumptions are discussed and illustrated by the results of a simple laboratory test. The implications of this work on the analysis of impact damaged laminates are then discussed.     

Power spectral density of CMI-coded TV signal transmitted through fibre-optic heterodyne system

An expression is derived for the power spectral density of a coded mark inversion (CMI) TV signal transmitted through a fibre-optic heterodyne system. An illustrative example is given, and its power spectral density has been computed numerically.     

Ultra-strong, well-apodised Bragg gratings in chalcogenide rib waveguides

The first ultra-strong, near-perfect, raised-apodised Bragg gratings in As/sub 2/S/sub 3/ chalcogenide rib waveguides using /spl lambda/=532 nm light and a modified Sagnac holographic writing setup are demonstrated. Good agreement is achieved between the experimental results and the numerical modelling of the gratings using the transfer matrix analysis for thin film structures.