Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

Reduced and differential parallel interference cancellation forCDMA systems

Since code division multiple access systems in multipath environments suffer from multiple access interference (MAI), multiuser detection schemes should be used in the receivers. Parallel interference cancellation (PIC) is a promising method to combat MAI due to its relatively low computational complexity and good performance. It is shown that the complexity of PIC is still high for realistic scenarios in terms of the symbol rate, the number of users, spreading gain, and multipath components. However, two novel methods are introduced to reduce significantly the complexity without sacrificing performance. The first approach, called reduced PIC, takes advantage of the composition of the interference to concentrate interference cancellation only on significant terms. The second approach, called differential PIC, exploits the multistage character of PIC to avoid unnecessary double calculations of certain terms in consecutive stages. It is shown that a combination of both approaches leads to a performance very close to the single-user bound whereas the complexity can be kept on the order of the conventional RAKE receiver     

Deformation behavior of HCP Ti-Al alloy single crystals

Single crystals of Ti-Al alloys containing 1.4, 2.9, 5, and 6.6 pct Al (by weight) were oriented for 〈a〉 slip on either basal or prism planes or loaded parallel along the c-axis to enforce a nonbasal deformation mode. Most of the tests were conducted in compression and at temperatures between 77 and 1000 K. Trace analysis of prepolished surfaces enabled identification of the twin or slip systems primarily responsible for deformation. Increasing the deformation temperature, Al content, or both, acted to inhibit secondary twin and slip systems, thereby increasing the tendency toward strain accommodation by a single slip system having the highest resolved stress. In the crystals oriented for basal slip, transitions from twinning to multiple slip and, finally, to basal slip occurred with increasing temperature in the lower-Al-content alloys, whereas for Ti-6.6 pct Al, only basal slip was observed at all temperatures tested. A comparison of the critically resolved shear stress (CRSS) values for basal and prism slip as a function of Al content shows that prism slip is favored at room temperature in pure Ti, but the stress to activate these two systems becomes essentially equal in the Ti-6.6 pct Al crystals over a wide range of temperatures. Compression tests on crystals oriented so that the load was applied parallel to the c-axis showed extensive twinning in lower Al concentrations and 〈c+a〉 slip at higher Al concentrations, with a mixture of 〈c+a〉 slip and twinning at intermediate compositions. A few tests also were conducted in tension, with the load applied parallel to the c-axis. In these cases, twinning was observed, and the resolved shear for plastic deformation by twinning was much lower that that for 〈c+a〉 slip observed in compression loading. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Sequential tripping strategy for a transmission network back-upprotection expert system

This paper describes a sequential tripping strategy used in a wide area back-up protection expert system (BPES) to combat situations in which protection relays have maloperated or information is missing. The BPES is an innovative back-up protection scheme designed to prevent the occurrence of widespread blackouts. The BPES evaluates the certainty that transmission lines are likely to be affected by the fault and uses a sequential tripping strategy to isolate the fault if a firm decision is not available due to maloperated relays and/or missing information. The mode of analysis and the sequential tripping strategy ensures that the BPES will clear a fault at minimum risk to the network. An example is included to demonstrate how the certainty factor based sequential tripping strategy is employed by the BPES to clear a fault which occurred on the South Western part of the UK National Grid System     

Bonding in cotton fiber from formaldehyde-free crosslinks

Cotton fabric was crosslinked with five agents, three of which were prepared form formaldehyde and two of which were formaldehyde-free. The formaldehyde-free agents produced less bonding between layers in the laminated microstructure of the cotton fiber. One agent, 4,5-dihydroxy-1,3-dimethyl-2-imidazolidinone, gave no evidence of any interlayer bonding. All five agents gave the same relationship between wrinkle recovery angle and molar substitution on the cotton up to moderate recovery angles, but only agents based on formaldehyde gave higher wrinkle recovery angles with additional reaction. Intralayer crosslinking did not reduce absorptivity, as shown by moisture regain and dye receptivity, but did restrict swelling in cupriethylenediamine hydroxide to the same extent as combined interlayer and intralayer crosslinking. The decrease in extensibility of treated fabric with increasing wrinkle recovery angle was the same with all agents. These results indicate the regions of the fiber that are important for each of these properties.     

Generalisations of Heyman's and Foulkes' theorems using dual formulation

Existing duality principles in structural optimisation are briefly reviewed and then they are extended to structures with segment-wise constant cross-sections. All theories are discussed in the particular context of optimal plastic beam design with symmetric convex specific cost functions and are confirmed by independent calculations on illustrative examples. It is shown that the optimal solution is always associated with a displacement field in which the mean absolute curvature value for each segment equals the subgradient of the specific cost function, with respect to the maximum absolute moment value for that segment. Moreover, the dual problem consists of the maximisation of the difference of two terms: the first one is the integral of the product of load and deflection (external work), and the second is the sum of products of segment lengths and the mean complementary cost values (taken with respect to the mean absolute curvature for that segment). Finally, some tentative proposals for a class of non-convex optimisation problems are presented. For special cases, the proposed general statements reduce to theorems by Heyman, Foulkes and Hemp.     

Finite-element grid improvement by minimization of stiffness matrix trace

A new and simple method of finite-element grid improvement is presented. The objective is to improve the accuracy of the analysis. The procedure is based on a minimization of the trace of the stiffness matrix. For a broad class of problems this minimization is seen to be equivalent to minimizing the potential energy. The method is illustrated with the classical tapered bar problem examined earlier by Prager and Masur. Identical results are obtained.     

Resonant neutron filters in elemental analysis and radiography

Translated from Atomnaya Énergiya, Vol. 67, No. 4, pp. 271–274, October, 1989.     

Multifunctional alkylphenol additive

Translated from Khimiya i Tekhnologiya Topliv i Masel, No. 2, pp. 14–15, February, 1989.