平面Z-型软磁铁氧体频率特性的研究

研究分析了Co2Z材料显微结构与磁性能的关系,在普通铁氧体工艺中引入预磁化处理方法,并适当控制二次再结晶现象,成功地研制出高性能的Co2Z型宽频材料,Z-型铁氧体材料的共振频率可达1.8GHz以上,截止频率在1GHz附近,起始磁导率在8-13之间,介电常数相对较低(ε'<30)。     

非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经预退火后的晶化动力学的DTA研究

研究了非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经400℃，保温10min预退火后的晶化动力学。结果表明；该合金的晶化相为α-Fe固溶体和Sm2Fe17Cx金属间化合物，两相的晶化表观激活能分别为557KJ/mol和514KJ/mol，当晶化体积分数为60%时，α-Fe相的晶化激活能达极大值；Sm2Fe17Cx相晶化激活能则随其晶化体积分数的增加而逐渐减小。     

工频电场对ADSS光缆特性的影响

随着电压等级的不断提高,超高压输电线路发展非常迅速.但是这些架空输电线路在运行时,附近存在较高的电场,对周围物体和公用走廊的其它线路会产生影响.电压等级越高,产生的电场影响越大.输电线路产生的电场越来越受到人们的重视.尤其是对于超高压输电线路,由于在电力铁塔上同塔悬挂全介质自承式光缆(ADSS),因此分析工频电场对ADSS光缆特性的影响非常必要.     

Selective recognition in molecularly imprinted polymer and its chromatographic characterization for cinchonine

A molecularly imprinting polymer (MIP) was synthesized via bulk polymerization under different conditions using anti-ague drug cinchonine (CN) as template. Infrared spectra (IR) results show that the template CNand functional monomer α-methyl acrylic acid (MAA) formed complexes before polymerization and the structure of complexes was simulated by Hyperchem. The results indicate that there are hydrogen bond or ionic bond between functional monomer and template molecule in acetonitrile solution. The MIP made in cold-initiated photo-polymerization has higher separation performance than that in the therm-initiated polymerization. The separation of the isomers CN and cinchonidine (CD) can be successfully obtained when its separate factor α reaches 1.82. Scatchard analysis suggests that the MIP recognizing CN with two classes of binding sites. The partition coefficient Kd, 1 and apparent maximum number nmax, 1 of binding sites with high affinity are 131.43 μmol/L and 58. 90 μmol/g, respectively,while Kd, 2 and nmax, 2 of binding sites with low affinity are 2.32 mmol/L and 169.08 mmol/g, respectively.     

Effect of partitioning on microstructure and properties of a medium carbon Ti Mo bearing high strength Q&P steel

In order to investigate the effect of partitioning procedures on microstructure and properties of a medium carbon Ti Mo bearing steel, the salt bath experiment, field emission SEM, TEM and tensile tests as well as wear tests were utilized to clarify the microstructural evolution and property changes treated by different partitioning parameters. The results show that the microstructures consist of tempered lath martensite, cementite and (Ti, Mo)C particles. With prolonging partitioning time or increasing partitioning temperature, the amount of laths martensite decreases and thicker martensite plates with blunt boundaries appear. In addition, with increasing partitioning temperature from 310℃ to 400℃, the tensile strength, hardness and low temperature toughness are simultaneously decreased, and the reduction reaches up to about 300MPa, 100HV and 20J, respectively. Finally, the wear performance of the samples partitioned below Ms is obviously better than that of samples partitioned above Ms. The morphology of worn surface of samples partitioned below Ms is characterized by plastic fatigue morphology, while the worn surfaces of samples partitioned above Ms are mainly dominated by grooves.     

环保易切削黄铜耐腐蚀性能研究

传统易切削黄铜多为铅黄铜，如HPb59-1、HPb63—3等，广泛应用于机械制造工业。铅黄铜零部件报废后将以各种形式污染环境。近年来，随着环保呼声的不断高涨，无铅易切削黄铜的研制成为必然。耐蚀性能是黄铜的重要使用性能之一，也是无铅易切削黄铜能否得到推广应用的关键。本实验以铋代铅并加入一定量的稀土制备的无铅易切削黄铜，其抗脱锌能力比传统易切削黄铜有较大提高。     

单源点法的一种改进

在应用能量线性叠加计算港内不规则波绕射系数时^[1,2]，通过假设不同的计算点具有不同的方向谱，从而增加单源点法考虑地形变化的能力。其中各计算点的方向谱由逆波向线追踪方向确定。本文由此观点建立数学模型。并通过实例计算。来验证这个想法。     

不用专门相移装置的三维面形测量

提出一种不需要专用相移装置实现相移，主要利用数字图像处理技术实现三维面形测量的方法，研究结果表明，用原干涉图像及1幅以上的移值条纹图主可能实现物体三维面形的测量。     

一种新的PCC-OFDM定时时偏盲估计

多项式相消编码PCC是一种编码技术，在PCC—OFDM调制中，它把将发送的信息调制到一组加权的子载波而不是单个子载波中去。PCC能够显著地降低OFDM对载波频偏的敏感性。本文对PCC—OFDM系统提出了一种新的定时盲估计，估计器是在接收机中的FFT之前进行的。基于PCC—OFDM的符号波形特征，构建定时时偏估计度量函数。最大化度量来估计定时时偏。本估计器不需要训练序列、导频信号或周期前缀。仿真表明，估计器在一个OFDM符号内收敛，且误差较小。     

自由锻锤上冷冲厚板新工艺

介绍了自由锻锤上冷冲厚板工艺的特点和模具主要结构。以及如何解决凸凹模间隙、选用小间隙冲孔时刃口磨损加剧的问题。研制出了降低磨损。提高模具寿命的润滑剂配方。设计了适合自由锻锤上厚板冲孔的模具，对在自由锻锤上厚板冲孔进行了有益的尝试。扩大了自由锻设备的加工范围。解决了不具备大型压力机情形下的生产难题。