Influence of Plasma Spray Parameters on Formation and Morphology of ZrO2–8 wt% Y2O3 Deposits

Spray prints of thermal spray coatings were created on glass slides for air-plasma-sprayed 8-wt%-yttria-partially-stabilized zirconia (YSZ) deposits. The spray parameters such as carrier gas flow rate, standoff distance, and torch power were systematically changed to investigate the influence of these parameters on the YSZ deposit characteristics. The deposit properties such as deposition efficiency (DE), substrate coverage, deposit thickness, and roughness were measured. The deposits sprayed with a 3.5–4.0 L/min carrier gas flow rate at an 80 mm standoff distance exhibited higher values of DE within the range of studied process parameters. The DE increased as much as 25% by varying the carrier gas flow rate from 2.0 to 4.0 L/min. The deposits sprayed at a higher standoff distance and low torch power gave poor deposit characteristics. The deposit characteristics were compared with the in-flight particle parameters and revealed that the deposit characteristics strongly depended on the in-flight particle temperature. Using the in-flight particle properties, the flattening ratio and the splat thickness were calculated. The average size of particles adhering to the substrate was found to drastically change with a change of process conditions, being much less than the average size of the starting powder.     

Real-time estimation of the electric parameters of an inductionmachine using sinusoidal PWM voltage waveforms

This paper studies the parameter estimation of induction machines. The problems associated with the parameter estimation of induction machines are analyzed through sensitivity functions. Then, models and a procedure to estimate a set of four basic parameters (r_s, σl_s, l_s, and τ_r) are proposed. The discrete-time parameter estimation models are written in the δ operator specifically because it provides good numerical properties at high sampling rates, where the discrete-time model approaches its continuous-time equivalent. This feature permits the direct estimation of the continuous-time parameters. The main feature of the proposed procedure is the possibility to estimate the parameters by using sinusoidal signals, and without the measurement of the machine speed. The experimental results obtained with the proposed estimation procedure are presented and demonstrate that it is possible to map the parameters in terms of the operating conditions of the induction machine     

Ni-65wt%Nb alloy by aluminothermic reduction process

Ni–Nb alloys have been used as master-alloy in the production of Ni-based superalloys containing niobium. In the case of INCONEL 718, the most used superalloy, the niobium content is in the range 5.0–5.5 wt%. The aim of this work is to present results related to the production of Ni-65wt%Nb alloy by aluminothermic reduction process. Two different reactant mixtures were used: Nb₂O₅ + Ni + Al and Nb₂O₅ + NiO + Al. For each type of mixture the Al excess was varied from 0% to 15% over the stoichiometric amount. All the alloys were produced in a bulk form with Nb and Ni composition according to specifications. The best results came from the experiments involving mixtures of Nb₂O₅ + NiO + Al, where an overall metallic yield of 86% was obtained. The alloys produced from Nb₂O₅ + Ni + Al mixtures showed low metallic yields and high oxygen contents associated to the presence of a niobium oxide-phase in the microstructure.     

Leaf and stem micromorphology of Byrsonima sericea DC. by light and scanning electron microscopy

Micromorphological studies were carried out using multiple microscopic techniques on the leaves and stem bark of Byrsonima sericea DC. (Malpighiaceae), a species popularly known as “murici” and used medicinally, in order to identify both qualitative and quantitative features of leaf and stem anatomy and histochemistry as differential parameters to support both the quality control of its ethnodrugs and the taxonomy of the genus. The study was conducted using traditional techniques of plant anatomy, histochemical tests, and the stomatal index (SI). Byrsonima sericea has hypostomatic leaves, anomocytic stomata, and its epidermal walls are anticlinal and straight on the adaxial and curved on the abaxial faces. T‐shaped trichomes were observed mainly on the abaxial surface. The leaf epidermis showed waxes syntopism on both surfaces, with the occurrence of different crystalloid forms on a single phylloplane. The mesophyll is dorsiventral, with 3‐4 collateral vascular bundles. Phenolic compounds, starch, and proteins were identified in the petiole and stem. The SI was 14.5 ± 0.53% (p < .05), but did not showed significant variations. A set of characters were found to be distinctive for the studied species, however, constituting parameters that could be used to separate B. sericea from other species of the genus.     

Recyclable,Flexible, Low‐Power Oxide Electronics

The ability to process and dimensionally scale field‐effect transistors with and on paper and to integrate them as a core component for low‐power‐consumption analog and digital circuits is demonstrated. Low‐temperature‐processed p‐ and n‐channel integrated oxide thin‐film transistors in the complementary metal oxide semiconductor (CMOS) inverter architecture are seamlessly layered on mechanically flexible, low‐cost, recyclable paper substrates. The possibility of building these circuits using low‐temperature processes opens the door to new applications ranging from smart labels and sensors on clothing and packaging to electronic displays printed on paper pages for use in newspapers, magazines, books, signs, and advertising billboards. Because the CMOS circuits reported constitute fundamental building blocks for analog and digital electronics, this development creates the potential to have flexible form factor computers seamlessly layered onto paper. The holistic approach of merging low‐power circuitry with a recyclable substrate is an important step towards greener electronics.     

Acoustic seafloor sediment classification using self-organizingfeature maps

A self-organizing feature map (SOFM), a kind of artificial neural network (ANN) architecture, is used in this work for continental shelf seafloor sediment classification. Echo data are acquired using an echosounding system from three types of seafloor sediment areas. Excellent classification (~100%) for an ideal output neuron grid size of 15×1 is obtained for a moving average of 35 input snapshots     

LAN emulation on an ATM network

The authors evaluate architecture alternatives relating to the provision of a LAN emulation service over a connection-oriented ATM network, and present the LAN emulation architecture as actually adopted by the ATM Forum LANE SWG. The role of servers is discussed as is the provision of broadcast/multicast services     

Solidification/stabilization of electric arc furnace dust using coal fly ash. Analysis of the stabilization process

In this paper, the stabilization of electric arc furnace (EAF) dust containing hazardous metals such as Pb, Cd, Cr or Zn is described. The treatment involves a waste solidification/stabilization (S/S) process, using coal fly ash as the fundamental raw material and main binder. The article also contains a brief review of the most important recent publications related to the use of fly ash as S/S agents.The efficacy of the process has been evaluated mainly through leaching tests on the solidified products and compliance with some imposed leachate limits. The concentration of metals leaching from the S/S products was strongly leachate pH dependent; thus, the final pH of the leachate is the most important variable in reaching the limits and, therefore, in meeting the stabilization goals.In this study, the dependence relationship between the leachate pH and the concentrations of metals in the leachate are analyzed; in some cases, this allows us to estimate the speciation of contaminants in the S/S solids and to understand the mechanism responsible for reduced leachability of heavy metals from solidified wastes.