Bright Blue Light—emitting Diodes Based on a Novel Fluorescent Dye Containing Heterocyclic Groups

Novel molecular material ,1-benzothiazoly-3-pheny1-pyrazoline (BTPP) was found to function as bright blue light emitting dye in organic electroluminescent device, and its optical and electric characteristics were investigated. This heterovyclic compound exhibited good characteristics of blue photoluminescence and electroluminescence,which had the emission peak at 450nm .The single layer light-emitting devices using BTPP as light -emitting material dispersed in poly(N-vinylcarbazole)(PVK) and double layer ones using PBD as hole block layer above the light-emitting layer were fabricated using conventional spin-casting and vaccum vapour deposition methods. The introduction of PBD has enhanced electron injection and luminance efficiency, compared with the single layer LEDs.     

非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经预退火后的晶化动力学的DTA研究

研究了非晶Sm5Fe74.3Nb1.5Si11.7B4.5C2.5Cu0.5合金经400℃，保温10min预退火后的晶化动力学。结果表明；该合金的晶化相为α-Fe固溶体和Sm2Fe17Cx金属间化合物，两相的晶化表观激活能分别为557KJ/mol和514KJ/mol，当晶化体积分数为60%时，α-Fe相的晶化激活能达极大值；Sm2Fe17Cx相晶化激活能则随其晶化体积分数的增加而逐渐减小。     

An FDTD/ray-tracing analysis method for wave penetration through inhomogeneous walls

A novel method of studying wave penetration through inhomogeneous walls using the hybrid technique based on combining finite-difference time-domain (FDTD) and ray tracing methods is presented . The FDTD method is used to analyze the transmission characteristics of inhomogeneous walls. Using the knowledge of the tangential electric and magnetic field distributions along the borders of the FDTD computation domain, rays are sent out to cover the rest of the environment so that prediction of signal coverage can be made more efficiently without compromising the accuracy. Numerical results of the method have been compared and shown to agree very well with those of measurement and those of full wave analysis. Examples have shown the inadequacy of the traditional ray tracing method in the presence of walls made of concrete blocks. However, the proposed method can accurately predict signal coverage by taking into account the scattered fields by the inhomogeneity inside the walls. The method does not add much to computational complexity. Reduction in computation time is even more significant when the incident waves can be approximated to be plane waves and the wall structure is periodic.     

Ti-23Al-14Nb-3V合金氩弧焊接头的显微组织及其力学性能

研究了预热对Ｔｉ－２３Ａｌ－１４Ｎｂ－３Ｖ合金焊接性，特别是对消除氩弧焊冷裂纹的作用以及对接头显微组织和力学性能的影响。结果表明，焊前预热可有效降低该合金的冷裂倾向。经预热处理后，焊缝区的结晶层状线消失，热影响区的硬度峰得到缓和，整个焊缝的显微硬度分布趋于均匀，但焊缝区的枝晶发生粗化，热影响区有所扩大。焊件接头的拉伸试验表明，预热可使焊缝区的接头强度系数增加，但无论预热与否，接头强度均低于母材强度，且不显示宏观塑性。     

纳米二氧化钛的表面修饰与应用的研究进展

介绍了纳米二氧化钛表面修饰的两种主要方法:无机和有机表面包覆,以及进行修饰后的纳米二氧化钛的应用.     

塑料片材的分切和分切对策

随着社会生产力的不断提高,人们生活水平的飞跃上升,特别是我国加入WTO以来,国际贸易更加繁忙,塑料包装的用量得到了空前的扩大,并呈现出快速发展的趋势。同时由于它们的迅速发展,对它们的要求已越来越严。而塑料包装中除了塑料容器外,几乎是片和膜包装,如热成型制品要用到各种塑料片材;软包装制品和彩印复合要用到各类塑料膜。而在生产塑料     

化学镀工艺在微电子材料中的研究和应用

简要综述了化学镀工艺在微电子材料中的应用,讨论了影响化学镀镍、铜、锡、钴和贵金属等的主要因素,阐述了化学镀微电子材料的特性、存在问题及研究动态。     

A Novel Channel Predictor Based on Constrained Hidden Markov Model

1　Introduction　Linkadaptationtechniqueisnowwidelyrecognizedasakeysolutiontoincreasethespectralefficiencyofwire lesssystems[1～ 3] .GPRS ,EDGE ,cdma2 0 0 0andWCDMAallincludelinkadaptationasameanstopro videhigherdatarates[4～ 5] .Torealizethepotentialoflinkadaptation ,reliablechannel predictionisneces sary[6 ] .　Therearemanydifferentchannelpredictionmethodsavailablenow ,suchasLongRangePrediction(LRP) [6 ] ,predictionbasedonsubspacesignalprocess ingalgorithms[7] ,predictionbasedonFinit…     

基于晶体双折射的光学FIR滤波器设计

提出建立在晶体双折射基础上，由晶体延迟片堆组成的光学FIR（Finite Impulse Response)滤波器设计方法，用以实现任意形状光谱输出。从FIR信号理论出发，建立了光学FIR滤波器数学模型，并分析了它与FIR滤波器的映射关系。在给出“输出反向传递法”来完成其光学实现同时，还以G／M滤波器设计实例证明其优良的光谱特性及角度特性。