The Effect of the Charge Fluctuation of Dust Parti-cles on Ion-acoustic Wave Excited Through Ionization Instability

The effect of the charge fluctuation of dust particles on ion acoustic wave (IAW) excited through ionization instability was investigated. The hydrodynamic equations and linear time-dependent perturbation theory served as the starting point of theory, by which the dispersion relation and growth rate of the IAW were given. By comparing the results with the case of constant dust charges, it was found that the charge fluctuation of dust particles reduces the instability of the wave mode.     

Hydrogen Reduction and Microstructural Changes of ISF Sinter

The reduction rate and microstructural changes of imperial smelting furnace (ISF) sinter have been investigated by means of thermogravimetric analysis, X-ray difFraction (XRD), scanning electron microscope (SEM ), energy dispersive analysis of X-ray (EDAX) and optical microscope.It is demonstrated that the overall reaction rate of the reduction is influenced by temperature and hydrogen partial pressure in H2 /N2 gas mixtures. There are two distinct zones observed in the partially reduced sinter. The reduction of zincite proceeds predominantly in a narrow range between the two zones, while the reduction of tead oxide and silicate takes place throughout the sinter. The differences between zincite and lead oxide or silicate in reducibility are analysed by thermodynamlcs. The phase transformations and microstructural changes occurring during the reduction process are discussed     

挠性抗回旋PDC钻头的有限元分析

回旋是导致PDC钻头早期失效的主要原因，介绍了一种基于挠性钻头的构想设计的抗回旋PDC钻头，阐述了其结构和抗回旋原理。对挠性钻头的公、母接头进行了有限元应力分析，说明了模型建立、网格划分以及约束和载荷施加过程中所采用的方法和关键技术。有限元分析结果表明挠性钻头的强度满足要求。     

阻尼式限流器参数的设计选择

本文阐述阻尼式限流器参数设计选择和产品系列规划的依据原则，并结合实例说明实施步骤与方法，以有助于限流器的正确设计与选用。     

体积-表面淬火中加热温度的自动控制

根据表面-体积淬火奥氏体规范的要求，分析了感应加热过程中温度控制的特点和方式，并介绍了采用红外线光导纤维测温和微机控温技术成功用于体积-表面淬火中透热温度的自动控制。     

正交曲线坐标下三维代数应力通量模型

针对弯曲及不规则明渠的水动力及物质输运特性，本文建立了曲线坐标系下的三维代数应力通量数学模型，对平面上弯曲及不规则复杂边界情形，采用Poisson方程进行正交曲线坐标变换，各向异性的湍流代数应力通量模型被引用于本文的模拟计算中，以体现复杂边界条件引起的水动力及物质输运特性的变化。通过180度强弯曲明渠水槽及贵溪电厂不规则边界河段物理模型试验两个实例计算表明，实测值与计算吻合良好，效果令人满意。     

FAFFA加速的PO-MM研究复杂金属载体上线天线电磁特性

本文提出了一种快速远场近似(FAFFA)加速的混合物理光学矩量法(POMM),利用FAFFA加速计算矩阵方程中的矩阵矢量积,明显提高了计算效率.对物体表面上的远场组之间的耦合作用推导出了一组简洁的计算公式,并分析了计算复杂度.复杂金属组合体上线天线输入导纳、互导纳和方向性图的计算结果与文献结果一致.利用该方法分析计算了一个舰船模型上线天线的电磁特性.数值结果表明了这种方法的正确性和工程应用中的有效性.     

12864-12 LCD模块与射频SoC nRF9E5的串行接口设计

本文首先介绍一种具有2位或3位串行、4位或8位并行多种接口方式，内部含有国标一级、二级简体中文字库的图形点阵液晶显示模块12864-12，以及该模块的技术特性、串行接口方式和操作指令。然后介绍射频片上系统nRF9E5的片内微控制器结构与其接口资源，给出在无线数据传输系统中12864-12与nRF9E5串行连接的硬件电路和部分程序。最后，论述了该方案的优点。     

TiO2纳米薄膜的微结构控制

通过有机酸修饰的水基so1-gel法，分别制备了由层状、针形和球形纳米粒子构成的纳米二氧化钛薄膜，采用SEM、XRD、红外光谱进行了表征.研究发现，调节水解过程中钛酸四丁酯：醋酸的摩尔比，可以控制薄膜的微结构，并对其机理进行了分析.该方法可以应用于sol-gel法制备其他纳米薄膜过程中的材料微结构控制.     

Delamination of thin film strips

Delamination of residually stressed thin film strips is analyzed to expose the dependence on strip width and film/substrate elastic mismatch. Isotropic films and substrates are assumed. The residual stress in the film is tensile and assumed to originate from mismatch due to thermal expansion or epitaxial deposition. Full and partial delamination modes are explored. In full delamination, the interface crack extends across the entire width of the strip and releases all the elastic energy stored in the strip as the crack propagates along the interface. The energy release rate available to propagate the interface crack is a strong function of the strip width and the elastic modulus of the film relative to that of the substrate. The energy release rate associated with full delamination is determined as a function of the interface crack length from initiation to steady-state, revealing a progression of behavior depending in an essential way on the three dimensionality of the strip. The dependence of the energy release rate on the remaining ligament as the interface crack converges with the strip end has also been calculated, and the results provide an effective means for inferring interface toughness from crack arrest position. A partial delamination propagates along the strip leaving a narrow width of strip attached to the substrate. In this case, the entire elastic energy stored in the strip is not released because the strain component parallel to the strip is not relaxed. A special application is also considered, in which a residually stressed metal superlayer is deposited onto a polymer strip. The energy release rate for an interface crack propagating along the interface between the polymer and the substrate is determined in closed form.