交联型聚醚聚氨酯的表征、力学性能及其碱金属盐络合物的导电性能

采用三羟甲基丙烷（ＴＭＰ）作交联剂与聚乙二醇（ＰＥＯ－１５４０）和甲苯二异氰酸酯（ＴＤＩ）反应，得到了具有较好力学性能的交联型聚醚聚氨酯（ＰＥＵ），该聚合物与ＬｉＣｌＯ４的结合物具有较高的室温电导率（σ３０℃＝１．８７×１０￣（－４）Ｓ／ｃｍ）。采用全反射红外光谱（ＡＴＲ－ＩＲ）对聚合物的结构进行了表征。对聚合物的组成、不同ＴＤＩ类型及络合盐浓度对聚合物力学性能及其络合物电导率的影响进行了探讨。低度交联聚合物的络合物，其电导率与温度的关系符合建立在自由体积理论上的ＶＴＦ方程，表明络合物中离子的传导主要是在无定形区域进行，与自由体积有关。     

Development of a low cost microwave mixer using a broad-band substrate integrated waveguide (SIW) coupler

A low cost single-balanced mixer is designed using a newly designed 90/spl deg/ substrate integrated waveguide (SIW) 3-dB coupler, which takes the advantages of low cost, low profile, and high performance. An X-band single-balanced SIW mixer is designed and fabricated with a standard printed circuit board process. Measured conversion loss of 6.8dB and the wide-band response from 8.5 to 12GHz are presented.     

MCM用氮化铝共烧多层陶瓷基板的研究

通过实验优化AlN(氮化铝)瓷料配方及排胶工艺,对共烧W(钨)导体浆料性能及AlN多层基板的高温共烧工艺进行了研究,并对AlN多层基板的界面进行了扫描电镜分析。采用AlN流延生瓷片与W高温共烧的方法,成功地制备出了高热导率的AlN多层陶瓷基板,其热导率为190 W/(m·K),线膨胀系数为4.6106℃1(RT~400℃),布线层数9层,W导体方阻为9.8 m,翘曲度为0.01 mm/50 mm,完全满足高功率MCM的使用要求。     

高硬度耐磨电弧喷涂管状丝材的研究

利用自熔性合金与非晶态材料的特点，研制了Fe—B系管状丝材作为电弧喷涂材料，其形成的涂层具有良好的结合强度、低的孔隙率、高的硬度和耐磨损性能。     

������ʧ��

��This work gives the concept about oil-cut,gas-cut, kick,grave kick,blowout and failure in controlling blowout and summarizes the type of failure in controlling blowout,the objective and man-made reasons causing blowout and the measures to prevent and control well blowout.     

Possible tactics to improve the growth of single-walled carbon nanotubes by chemical vapor deposition

The growth time, growth mode and the method of preparing the supported catalysts play an important role in the growth of single-walled nanotubes (SWNTs). Their effects on the chemical vapor deposition (CVD) growth of SWNTs with MgO-supported catalysts were investigated in this study. It is shown that the growth rate of SWNTs was large during the initial few minutes of growth, however the quality of the tubes was low owing to the formation of many defects. Long term growth may favor the formation of tubes with high quality and high yield, but the introduction of other forms of carbon (impurities) is also unavoidable. There was a balance between the increase in yield and quality and sacrifice of the purity during growth of SWNTs. MgO-supported catalysts prepared by the co-precipitation method were found to be more effective for the synthesis of SWNTs than those prepared by the widely used impregnation method. The size and dispersion state of the catalyst were found to be crucial in enhancing the growth of SWNTs. In addition, growth on the surface of SWNTs over nanosized catalyst films was shown to be more favorable for the synthesis of tube products with higher quality, yield and purity.     

天康面粉公司制粉车间局部技改介绍

山东巨野国家粮食储备库天康面粉公司制粉车间始建于2000年,设计能力为处理小麦100t/d.主要设备有FMFQ10×2/6×2磨粉机8台,FS-FG6×24C高方筛3台,FQFD50×2×3清粉机2台,磨辊总接触长度12000 mm,平筛总筛理面积138.8 m2,单位磨辊接触长度12 mm/(100kg·d),单位平筛筛理面积0.14 m2/(100kg·d).麦间清理工艺(包括初清)为4筛2打2去石3磁选2着水,粉间工艺为488M1S2T4P3Br.     

小剂量辐照小鼠胸腺细胞膜流动性的变化

报道了以茈为荧光探针,探讨小剂量~(60)Co γ射线照射后小鼠胸腺细胞膜流动性的变化。结果表明,剂量在0.25-1.00Gy范围,胸腺细胞膜流动性降低与剂量之间呈明显线性关系。从0.50Gy起,辐照组荧光强度比值I_1/I_2与I_3/I_2与对照组的比较存有显著差异(P<0.05)。提示淋巴细胞膜流动性的变化可作为小剂量辐照早期效应的敏感指标。     

把中国建设成世界有色金属制造业基地的对策研究

本文首先介绍了我国有色金属工业的现状以及当前世界有色金属工业发展的新格局,并分析了中国成为世界有色金属制造业基地的支撑条件,最后提出了关于建设具有特色的中国有色金属制造业基地的几点看法。     

台达变频器在纺织织带盘带机上的应用

盘带机是纺织织带成品分卷设备，需要使用到收放卷控制。本文基于台达变频器在盘带机上的应用案例，论述盘带机自动化系统设计调试过程以及遇到的问题分析。