Screening vegetable oil alcohol esters as fuel lubricity enhancers

Methyl and ethyl monoalkyl esters of various vegetable oils were produced for determining the effects of type of alcohol and fatty acid profile of the vegetable oil on the lubricity of the ester. Four methyl esters and six ethyl esters were analyzed for wear properties using the American Society for Testing and Materials method D 6079, Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig. Ethyl esters showed noticeable improvement compared to methyl esters in the wear properties of each ester tested. No correlation was found between lubricity improvement and fatty acid profile of the ester, except that esters of castor oil had improved lubricity over other oils with similar carbon chain-length (C₁₈) fatty acids.     

Effect of catalyst type on the kinetics of the photoelectrochemical disinfection of water inoculated with E. coli

The rates of the photoelectrochemical disinfection of Escherichia coli at TiO₂ electrodes were measured as a function of concentration and applied potential. Two different TiO₂ photoelectrodes were used: a thermally treated titanium plate and a porous film prepared by a sol–gel hydrolysis technique. The kinetics of the disinfection process were found to depend upon the nature of the electrode material. For the thermal film they were first order, and half order for the sol–gel film. It was also found that the catalytic activity per unit surface area of catalyst is many orders of magnitude greater than that observed using TiO₂ slurries; this was attributed to the reduced rate of electron-hole recombination afforded by the application of a small potential bias (1 V vs Ag/AgCl), and hence the exploitation of the electric field enhancement (EFE) effect.     

A cathode support structure for use in a magnetron oscillator experiment

A low temperature co-fired ceramic (LTCC) material system has been used to develop a protype field emission cathode structure for use in an experimental magnetron oscillator. The structure is designed for used with 30 gated field emission array (GFEA) die electrically connected through silver metal traces and electrical vias. To approximate a cylinder, the cathode structure (48 mm long and 13.7 mm in diameter) is comprised of 10 faceted plates which cover the GFEA dies. Slits in the facet plates allow electron injection. The GFEA die (3 mm × 8 mm) are placed in axial columns of 3 and spaced azimuthally around a cylindrical support structure in a staggered configuration resulting in 10 azimuthal locations. LTCC manufacturing techniques were developed in order to fabricate the newly designed cathode with seven layers wrapped to form the cylinder with electrical traces and vias. Two different cathode wrapping techniques and two different via filling techniques were studied and compared. Two different facet plate manufacturing techniques were studied. Finally, four different support stand configurations for firing the cylindrical structure were also compared with a square post stand having the best circularity and linearity measurements of the fired structure.     

Yield stress distribution in injection‐moulded glassy polymers

A methodology for structural analysis simulations is presented that incorporates the distribution of mechanical properties along the geometrical dimensions of injection‐moulded amorphous polymer products. It is based on a previously developed modelling approach, where the thermomechanical history experienced during processing was used to determine the yield stress at the end of an injection‐moulding cycle. Comparison between experimental data and simulation results showed an excellent quantitative agreement, both for short‐term tensile tests as well as long‐term creep experiments over a range of strain rates, applied stresses, and testing temperatures. Changes in mould temperature and component wall thickness, which directly affect the cooling profiles and, hence, the mechanical properties, were well captured by the methodology presented. Furthermore, it turns out that the distribution of the yield stress along a tensile bar is one of the triggers for the onset of the (strong) localization generally observed in experiments. © 2015 Society of Chemical Industry     

Lignin‐based carbon fibers: Accelerated stabilization of lignin fibers in the presence of hydrogen chloride

Organosolv switchgrass lignin (SGL) and hardwood lignin (HWL) polymers are used as precursors to prepare low cost carbon fibers (CFs). Lignin powder and fiber samples are stabilized and carbonized at different conditions to investigate the effect of HCl on thermal‐oxidative stabilization time, mass yield, fiber diameter, and mechanical properties. The results show that HCl can accelerate stabilization and reduce the stabilization time from many hours to 75 min for the SGL fibers, and to 35 min for the HWL fiber. The rate of rapid stabilization in HCl/air is at least four times faster than conventional stabilization in air. The CFs prepared with two different stabilization methods have almost the same strength and modulus, but higher carbon yield is obtained with the rapid stabilization due to a short time of oxidation. Pores and defects observed on the surface and the cross‐section of the CFs across all stabilization conditions contribute to low fiber strength. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45507.     

Codeposited chromium and silicon diffusion coatings for Fe-Base alloys via pack cementation

The simultaneous deposition of Cr and Si into plain carbon, low-alloy, and austenitic steels using a halide-activated pack-cementation process is described. Equilibrium partial pressures of gaseous species have been calculated using the STEPSOL computer program to aid in designing specific processes for codepositing the desired ratios of Cr and Si into a given alloy. The calculations indicate that NaCl-activated packs are chromizing, while NaF-activated packs deposit more Si with less Cr. The use of a dual activator (e.g., NaF+NaCl) allows for the deposition of both Cr and Si in the desired amounts. Single-phase ferritic coatings (150–250 microns thick) with a surface concentration of 20–35 wt.% Cr and 2–4% Si have been grown on AISI 1018, Fe-2.25 Cr-1.0Mo-0.15C, and Fe-0.5 Cr-0.5 Mo-0.2C steels using packs containing a 90 wt.% Cr-10Si binary source alloy, a NaF+NaCl activator, and a silica filler. Two-phase coatings (approximately 75 microns thick) containing 20–25 wt.% Cr and 2.0–2.4% Si have been obtained on 304 stainless steel using packs containing a 90 wt.% Cr-10Si binary source alloy, a NaF activator, and an alumina filler. The same pack chemistry allowed the diffusion of Cr and Si into the austenitic Incoloy 800 alloy without a phase change. A coated Fe-2.25 Cr-1.0 Mo-0.15 C coupon with a surface concentration of Fe-34 wt.% Cr-3Si was cyclically oxidized in air at 700°C for over four months and 47 cycles. The weight gain was very low (<0.2 mg/cm²) with no scale spalling detected. Coated coupons of AISI 1018 steel, and Fe-0.5 Cr-0.5 Mo-0.2C steel have shown excellent oxidation-sulfidation resistance in reducing, sulfur-containing atmospheres at temperatures from 400 to 700°C and in erosion and erosion-oxidation testing in air at 650 and 850°C.     

Fine grinding of thermoplastics by high speed friction grinding assisted by guar gum

High speed friction grinding has been used to grind plant and food substances in water but never been explored for grinding of thermoplastics like polylactic acid (PLA), low and high density polyethylene and polypropylene. Such grinding was investigated in this work and was made possible by using 0.5% guar gum solution instead of just water because increasing the viscosity of water reduced their settling and the speed of passing through the grinder. Tensile, flexural, and impact strengths of the plastics were studied and higher grinding efficiency of PLA could be explained by its low elongation-at-break compared to low density polyethylene, high density polyethylene, and polypropylene. The microplastics (2000–45 μm) were studied for mass and particle size distributions and by scanning electron microscopy, ¹³C CP/MAS NMR, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. In addition, viscosity of guar gum and contact angles was measured. This new technology can produce finely ground microplastics (710–45 μm) for a variety of applications.