Drug release from heat-treated polyvinyl alcohol films

Polyvinyl alcohol (PVA) films containing 10% w/w of a model drug, sulphathiazole, were cast from aqueous solutions and subjected to heat treatment at specific temperatures for known periods of time. Heat treatment at temperatures above the T_g of the PVA films slowed down the rate of drug release from the films. Increasing the temperature of heat treatment from 120°C to 160°C further decreased the rate of drug release. On the other hand, if the heat treatment were conducted at a temperature below the T_g e.g. at 80°C, there were insignificant differences between the release profile of sulphathiazole from heat-treated films and that from untreated films. The duration of heat treatment affected the rate of drug release to a smaller extent compared to the temperature of heat treatment. These results correlated with the heat induced changes in the morphology of, and in the extent of water uptake by the PVA films.     

A three-dimensional model for suspension-to-membrane-wall heat transfer in circulating fluidized beds

A three-dimensional model is proposed for both furnace-side and wall-side heat transfer in circulating fluidized beds with membrane walls. Following previous publications (Int. J. Heat Mass Transfer (2003a, b)), a core-annulus flow structure is employed in the model, with consideration of the membrane wall influence on bed hydrodynamics. The model couples radiation, conduction and convection on the furnace side to conduction and convection on the wall side. Radiation in the wall layer is simulated by the moment method. A finite-element method is employed to solve the set of non-linear, partial differential equations. The solution is demonstrated for a typical example. The model gives predictions of suspension-to-wall heat transfer which show satisfactory agreement with published experimental data.     

Nitrogen removal using recycled polystyrene bottles as biofilm media

The performance of an attached growth wastewater treatment process was investigated in an effort to improve nitrogen removal efficiency. Recycled Yakult (lactic acid fermentation drink) bottles made of polystyrene were used as a biofilm media. The use of Yakult bottles as a biofilm media has been attempted by numerous researchers in Japan for the removal of solids and organics. However, these studies focused only on the removal of solids and organics. This study extended their application to the removal of nitrogen for domestic sewage treatment. Yakult media was placed in a reactor with 70% apparent reactor volume in a conventional A/O process. The bottom of the Yakult media was removed, and randomly filled Yakult media were effectively able to reduce the flow in tanks, resulting in an increase in the contact time between pollutants and microorganisms. With higher HRT, the nitrogen removal efficiency was increased by up to 83% with 12 hr of HRT. Nitrification appeared to be the limiting factor of nitrogen removal at an HRT that is less than 12 hr, indicating that the Yakult process requires more retention time to achieve nitrification compared to other biofilm processes. The removal efficiencies of organics and solids were high regardless of the change of operational parameters. This article is based on a presentation in “The 7th Korea-China Workshop On Advanced Materials” organized by the Korea-China Advanced Materials Cooperation Center and the China-Korea Advanced Materials Cooperation Center, held at Ramada Plaza Jeju Hotel, Jeju Island, Korea on August 24–27, 2003.     

An interactive lung field segmentation scheme with automated capability

Feasible clinical application of any automated segmenting methodology demands more than just accuracy. Amendment to the automated delineation is necessary when the algorithm fails, however, integrated solution to such a scenario is largely absent in literature. Hence in this survey we devised an architecture that does both the automated and interactive lung field localizations using a single segmenting engine—random walker algorithm—so that intuitive amendment is only necessary when the automated generated delineation is unsatisfactory. The algorithm proceeds by first extracting 18 intensity profiles running horizontally, each of them equally spacing apart, and in each intensity profile three extreme points denoting the two lungs and the esophagus are determined through profile matching. This done, the algorithm removes profiles that do not intersect with the lung, and the rest of the extreme points are plugged into random walker algorithm to perform segmentation. The achieved accuracy in localization by the above was 0.8875 in terms of overlap measure (the maximum value for this parameter is 1) over 341 images. In the case where unsatisfactory delineation prompts amendment necessary, the user can interactively segment the lung by just a shift on some of the previous-determined points to the desired locations, and random walker algorithm is run again with the amended input. By such a fusion, the benefits of both the automated and interactive segmentation are shared in a single architecture.     

Biodegradation of estrogen conjugates by bacteria isolated from river sediments

The objective of this study was to investigate the ability of E. coli in river sediments to degrade estrogen conjugates. Biodegradation experiments on glucuronide estrogens (E1-GLU, E2-GLU and E3-GLU) using E. coli, non-E. coli bacteria as well as sediment crude extracts were carried out in batch mode. A pure identified E. coli strain (KCTC 2571) was used for comparison of enzyme activity. The results showed that the degradation rate of estrogen conjugates by KCTC 2571 and E. coli isolated from sediments followed a similar trend. Fecal bacteria showed a high ability to deconjugate glucuronided estrogens. Approximately 50% of glucuronide moieties were cleaved within 4 h of contact time in experiments using pure E. coli. The degradation rate was slower in experiments using crude extracts of sediments, and conjugated estrogens were not completely degraded even after 12 h of reaction. These results provide a clear understanding of the fate and behavior of estrogen by bacteria in the environment.     

Pitchfork bifurcation and flip-flop operation with a coupled nonlinear system

A ring cavity system consisting of two hybrid Michelson interferometers coupled together with feedback is constructed. This system shows spatial bifurcation and can be utilized as an all-optical flip-flop device. We demonstrate experimentally a flip-flop operation by use of only a positive pulse in this system.     

Metal Ions versus Protons: Tracking of Charge-Carrier Insertion into a Cathode Oxide in Aqueous Rechargeable Batteries

Protons in aqueous electrolytes can perform as an additional type of charge carrier for insertion/extraction in addition to the primary carrier cations in aqueous rechargeable batteries. Despite many diverse claims regarding the effect of protons, mutually conflicting experimental results and their interpretations without direct evidence have been reported over the last decade. Systematic examinations and analyses are thus imperative to clarify the conditions of proton insertion in aqueous rechargeable batteries. Utilizing V₂O₅ as a model cathode and beaker-type cells with a sufficient amount of ZnSO₄ aqueous electrolytes in this work, it is demonstrated that protons are inserted into the cathode prior to Zn-ions in low-pH conditions (pH ≤ 3.0). In stark contrast, the influence of protons on the discharge voltage and capacity is insignificant, when either the pH becomes higher (pH ≥ 4.0) or the electrolyte volume is considerably low in coin-type cells. Similar behavior of pH-dependent proton insertion is also verified in Na–, Mg–, and Al-ion electrolytes. Providing a resolution to the controversy regarding proton insertion, the present study emphasizes that the influence of protons substantially varies depending on the pH and relative volume of electrolytes in aqueous batteries.     

On measuring network robustness for weighted networks

Knowledge and Information Systems - Network robustness measures how well network structure is strong and healthy when it is under attack, such as vertices joining and leaving. It has been widely...     

Metal microparticle – Polymer composites as printable,bio/ecoresorbable conductive inks

Biologically and environmentally resorbable electronic devices support application possibilities that cannot be addressed with conventional technologies. This paper presents highly conductive, water-soluble composites that can be printed to form contacts, interconnects, antennas, and other important features that are essential to nearly all systems of this type. An optimized material formulation involves in situ polymerization to yield a polyanhydride containing a dispersion of molybdenum microparticles at appropriate concentrations. Comparisons of essential physical and electrical properties of these materials to those of composites formed with other polymers and other metal microparticles reveal the relevant considerations. Various functional demonstrations of screen-printed test structures and devices illustrate the suitability of these conductive inks for use in water-soluble electronic devices. A key advantage of the material introduced here compared to alternatives is its ability to maintain conductance over significant periods of time while immersed in relevant aqueous solutions. Studies involving live animal models establish the biocompatibility.