Friction and wear of Inconel 690 and Inconel 600 for steam generator tube in room temperature water

In the steam generators of nuclear power plants, the flow of cooling water can cause the tubes to vibrate, resulting in fretting wear damage due to contacts between these tubes and their supports. The tubes are made of Inconel 690 and Inconel 600 and the supports are made of STS 304. In this paper, fretting wear tests in water were performed using the materials Inconel 690 and Inconel 600 in contact with STS 304. Fretting tests using a cross-cylinder type set up were conducted under various vibrating amplitudes and applied normal loads in order to measure friction forces and wear volumes. Also, conventional sliding tests using a pin-on-disk type set up were carried out to compare these test results.In the fretting tests, friction force was found to be strongly dependent on normal load and vibrating amplitude. Coefficients of friction decreased with an increase in the normal load and a decrease in the vibrating amplitude applied. Also, the wear of Inconel 600 and Inconel 690 was predicted using a work rate model. Depending on the normal load and vibrating amplitude applied, distinctively different wear mechanisms and often drastically different wear rates occurred. It was found that the fretting wear coefficients for Inconel 600 and Inconel 690 were 9.3×10⁻¹⁵ and 16.2×10⁻¹⁵ Pa⁻¹, respectively. This study shows that Inconel 690 can result in lesser friction forces and exhibits less wear resistance than Inconel 600 in room temperature water.     

Exponential Stability of Interval Dynamical Systems with Quadratic Nonlinearity

This article proposes an approach for investigating the exponential stability of a nonlinear interval dynamical system with the nonlinearity of a quadratic type on the basis of the Lyapunov’s direct method. It also constructs an inner estimate of the attraction domain to the origin for the system under consideration.     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.     

Drug release from heat-treated polyvinyl alcohol films

Polyvinyl alcohol (PVA) films containing 10% w/w of a model drug, sulphathiazole, were cast from aqueous solutions and subjected to heat treatment at specific temperatures for known periods of time. Heat treatment at temperatures above the T_g of the PVA films slowed down the rate of drug release from the films. Increasing the temperature of heat treatment from 120°C to 160°C further decreased the rate of drug release. On the other hand, if the heat treatment were conducted at a temperature below the T_g e.g. at 80°C, there were insignificant differences between the release profile of sulphathiazole from heat-treated films and that from untreated films. The duration of heat treatment affected the rate of drug release to a smaller extent compared to the temperature of heat treatment. These results correlated with the heat induced changes in the morphology of, and in the extent of water uptake by the PVA films.     

A Survey on the Numerics and Computations for the Landau-Lifshitz Equation of Micromagnetism

The Landau-Lifshitz (LL)equation of micromagnetism governs rich variety of the evolution of magnetization patterns in ferromagnetic media. This is due to the complexity of physical quantities appearing in the LL equation. This complexity causes also an interesting mathematical properties of the LL equation: nonlocal character for some quantities,nonconvex side-constraints, strongly nonlinear terms. These effects influence also the numerical approximations. In this work, recent developments on the approximation of weak solutions, together with the overview of well-known methods for strong solutions,are addressed. Author is supported by the Fund for Scientific Research - Flanders FWO (Belgium).