Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

Coordinating Agents in Shop Floor Environments From a Dynamic Systems Perspective

In this paper, we address agent coordination from a dynamic systems perspective and propose a dynamic coordination model, which is inspired by biological metabolic systems. A new coordination mechanism through dynamic local adjustment (CDLA) is presented, and coordination is achieved when every agent utilizes explicitly the global system dynamics and performs iteratively a dynamic local adjustment procedure. The CDLA mechanism is investigated in an example multiagent shop floor system. The results show that the example manufacturing process is well-coordinated and the coordination approach is practically applicable and effective     

Analysis of ATSC field test results in Taiwan

Field tests of the transmission performance of the ATSC DTV system have been conducted in Taiwan. The test results as well as comparisons against the NTSC system performance are reported and analyzed. From the measured results the reception characteristics of the DTV can be deduced and can provide guidelines for television stations to design the transmission system, schedule equipment deployment, plan service coverage areas, and improve the reception quality of the digital signal     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

自主创新导向下的TD-SCDMA与NGBWM务实发展战略思考

以TD—SCDMA既有进展及面临的挑战与NGBWM的发展走向为基础，重点论述自主创新导向下的TD—SCDMA与NGBWM务实发展战略思考。     

The uniformly valid asymptotic solutions of transient cone segments in pressure vessels

In this paper, according to the theory of thin shells, a basic equation in complex form is derived for conical thin shells with linearly varying wall thickness under symmetric loads, and the uniformly valid asymptotic solutions are given.     

A Subcarriers Allocation Scheme for Cognitive Radio Systems Based on Multi-Carrier Modulation

Cognitive radio (CR) is a dynamic spectrum access technology as a solution to spectrum under-utilization problem in some licensed bands. Operating over an exceedingly wide spectrum, CR systems usually adopt multi-carrier modulation (MCM) to implement flexible channelization. Consequently, efficient channel allocation scheme becomes extremely important to an MCM based CR (MCM-CR) system. In this paper, a maximum likelihood detection model is developed to detect the presence and locations of licensed users (LUs) signals in the frequency domain. Performance of the detection model, including the optimal detection region, detection probability and false alarm probability, is analyzed. A one-order two-state Markovian chain model is proposed to predict channel status information. In particular, a novel subcarrier allocation scheme for MCM-CR systems is proposed, taking into account the confidence of channel estimation, quality of services (QoS) of rental users (RUs) and throughput. To validate the analytical results, simulations have been conducted to show effectiveness of the proposed scheme.     

第七届中国国际橡胶技术展暨第一届亚洲埃森轮胎展系列报道二:橡胶机械系列报道三:橡胶检测设备

国内主要参展商 1.益阳橡机 益阳橡胶塑料机械集团有限公司在本次展会上,推出了一款GE-5实验室用密炼机,容积5升,啮合型转子,用于橡胶制品、白炭黑、特种胶的混炼.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.