Phase composition and properties of solid solutions of GdFeO3–GdInO3 bulks

Solid solutions of the GdFeO₃–GdInO₃ system were prepared at 1550 °C by ceramic powder processing. The formulated composition was Gd(Fe_1−xIn_x)O₃ (GFI) with the indium contents at x = 0, 0.25, 0.5, 0.75, and 1.0. A stable phase of Gd(Fe_1/3In_2/3)O₃ in our system was identified by X-ray diffraction and phase composition analysis. Multi-phase morphologies were observed for GFI bulks with x = 0.5 and 0.75. Dielectric and electrical properties of the GFI bulks were investigated. The addition of 25% In³⁺ in GdFeO₃ had an obvious enhancement in polarization and led to an elevated resonance frequency. Dielectric properties of GFI bulks except GdInO₃ were strongly dependent upon the test frequency, which corresponded to the response of polarization mechanism. GdInO₃ displayed as a stable dielectric, which was frequency- and temperature-insensitive. GdInO₃ was thermally activated and became leaky until above 600 °C.     

纸张用有机硅抗水剂的制备

采用氨基硅油、十二烷基三甲氧基硅烷、甲基三乙氧基硅烷配成11种抗水剂,用于纸张的抗水处理.通过渗透法和接触角法测试发现,有机硅抗水剂对实验选择的9种纸张均有明显的抗水效果;其中采用氨基硅油配制的抗水剂效果最好,经其处理的生宣纸与空白样相比,接触角由完全润湿提高到125°,渗透时间由0提高到18 s.最佳应用工艺为:将氨基硅油配制成质量分数为2.041%的甲苯溶液,按照10g/m2的涂布量喷涂于纸张表面,自然晾干3～5天至恒定质量.     

Photocatalytic degradation of 2,2‐bis(4‐hydroxy‐3‐methylphenyl) propane (BPP) based on molecular recognition interaction

BACKGROUND: Endocrine disruptors in the aquatic environment and their potential adverse effects are currently issues of concern. One of these endocrine disruptors is 2,2‐bis(4‐hydroxy‐3‐methylphenyl)propane (BPP). In this work the molecular recognition interaction of BPP with β‐cyclodextrin (β‐CD) was studied using IR spectroscopy and steady state fluorescence spectroscopy, and the photocatalytic degradation behaviour of BPP based on molecular recognition interaction was investigated in a TiO₂/UV–visible (λ_max = 365 nm) system. This might provide a new method for the treatment of some organic pollutants in wastewater. RESULTS: β‐CD reacts with BPP to form a 1:1 inclusion complex, the formation constant of which is 4.94 × 10³ L mol^?1. The photodegradation rate constant of BPP after molecular recognition by β‐CD showed a 1.42‐fold increase in the TiO₂/UV–visible (λ_max = 365 nm) system. The photodegradation of BPP depended on the concentration of β‐CD, the pH value, the gaseous medium and the initial concentration of BPP. The photodegradation efficiency of BPP with molecular recognition was higher than that without molecular recognition. After 100 min of irradiation the mineralisation efficiency of BPP after molecular recognition by β‐CD reached 94.8%, whereas the mineralisation efficiency of BPP before molecular recognition by β‐CD was only 40.6%. CONCLUSION: The photocatalytic degradation of BPP after molecular recognition by β‐CD can be enhanced in the TiO₂/UV‐visible (λ_max = 365 nm) system. This enhancement is dependent on the enhancement of the adsorption of BPP, the moderate inclusion depth of BPP in the β‐CD cavity and the increase in the frontier electron density of BPP after molecular recognition. Copyright © 2008 Society of Chemical Industry     

Recovery of pyruvic acid with weakly basic polymeric sorbents

BACKGROUND: Carboxylic acids are among the most important substances that can be manufactured from biomass. However, the recovery of carboxylic acids from fermentation broths presents a challenging separation problem. To avoid the production of waste salts and net consumption of chemicals in the calcium carboxylate salt process, the use of reversible chemical complexation with polymeric sorbents and extractants is attractive for carboxylic acid recovery. Pyruvic acid is widely used in the manufacture of medicines, pesticides and foodstuffs and can be produced by fermentation. Since the acidity of pyruvic acid (pK_a = 2.49) is stronger than that of normal carboxylic acids, and as few reports on the recovery of pyruvic acid are available, the sorption of pyruvic acid from aqueous solution on two types of weakly basic polymeric sorbent, tertiary amine D301R and primary amine D392, was investigated over a wide pH range and at various salt (MgSO₄) concentrations. RESULTS: Overloading adsorption of pyruvic acid on both weakly basic polymeric sorbents occurred, with the overloading of D392 being greater than that of D301R. The adsorption of pyruvic acid on both sorbents was greatly affected by the solution pH and the salt concentration in the aqueous phase. An overloading model was able to predict the experimental uptake data very well. CONCLUSION: Solution pH is one of the most important operating conditions, and both polymeric sorbents D392 and D301R can be used to recover pyruvic acid from dilute aqueous solution with high efficiency at a solution pH around 2. The uptake by D392 is greater than that by D301R owing to steric hindrance of the tertiary amine. Copyright © 2008 Society of Chemical Industry     

保山气田新近系羊邑组二-三段沉积微相

保山盆地为滇西的一个具西断东超箕状断陷结构的新近系小型盆地。为搞清区内保山气田的沉积特征，指导该区油气勘探工作，结合沉积岩（物）与沉积环境之间的辩证关系，通过对沉积岩的岩性特征（颜色、岩石类型、岩石结构、黏土矿物、岩相组合）的分析研究，借助于沉积相在测井和地震剖面上的显著特征，研究并划分了保山气田新近系上新统羊邑组二-三段的沉积微相类型。结果表明，在该研究区主要发育了扇三角洲前缘亚相中的水下分流河道、分流河道间、前缘席状砂、河口坝等沉积微相类型，以及浅湖亚相中的浅湖泥和浅湖漫流席状砂沉积微相。剖析各类骨架微相的沉积特征后指出：水下分流河道、河口坝和前缘席状砂为该区最有利的储集砂体。     

Growth and morphology of nanometer LiMn2O4 powder

The growth of Li_1+xMn₂O₄ via detonation reaction was investigated with respect to the presence of an energetic precursor, such as the metallic nitrate and the degree of confinement of the explosive charge. The detonation products were characterized by scanning electron microscopy. Powder X-ray diffraction and transmission electron microscopy were used to characterize the products. Li_1+xMn₂O₄ with 1-2 μm spherical morphology and more uniform secondary particles, but with smaller primary particles of diameters from 20 to 60 nm and a variety of morphologies were found. The oxides produced by this cheap method affirmed the validity of detonation synthesis of nano-size powders.     

Periodic surface modeling for computer aided nano design

Current solid and surface modeling methods based on Euclidean geometry in traditional computer aided design are not efficient in constructing a large number of atoms and particles. In this paper, we propose a periodic surface model for computer aided nano design such that geometry of atoms and molecules can be constructed parametrically. At the molecular scale, periodicity of the model allows thousands of particles to be built efficiently. At the meso scale, inherent porosity of the model represents natural morphology of polymer and macromolecule. Surface and volume operations are defined to support crystal and molecular model creation with loci and foci periodic surfaces. The ultimate goal is to enable computer assisted material and system design at atomic, molecular, and meso scales.     

浅谈集成电路的废气处理

集成电路的工业废气有含氟化物、硫酸雾的酸性废气,含氨的碱性废气,含异丙醇、光刻胶的有机废气,含SiO_2的含尘废气,以及含硅烷、磷烷的工艺尾气等,这些工业废气中大部分成分是有毒有害的,必须进行有效的处理才能排入大气中。主要讨论上述工业废气的分类、处理方式、应用范围及应用实例等。     

En/Decoder for Spectral Phase-Coded OCDMA System Based on Amplitude Sampled FBG

A novel en/decoder for spectral phase-coded optical code-division multiple-access system based on amplitude sampled fiber Bragg grating (FBG) is proposed. Both equivalent chirp and equivalent phase shift are achieved by amplitude sampling. Compared with previous en/decoder based on step chirped FBG, it is easier to fabricate. The performance of the proposed en/decoder is verified by both numerical simulation and experimental demonstration.