悬浮床加氢裂化油溶性催化剂与沥青质的作用

在高压釜反应器中对添加了油溶性 Ni 催化剂(UPC-O)和水溶性 Ni 催化剂(UPC-W)的辽河稠油常压渣油(LHAR)进行了悬浮床加氢裂化实验。通过元素分析和傅里叶变换红外光谱(FTIR)分析对抑制反应生焦效果好的 UPC-O 与 LHAR 沥青质的作用进行了研究。元素分析结果显示,在 LHAR 中加入 UPC-O1000μg/g,沥青质和脱沥青质油中 Ni 含量分别出476μg/g和110μg/g 增加到7 559μg/g 和1 024μg/g,表明 UPC-O 在沥青质中有富集的趋势。FTIR 表征结果显示,UPC-O 和沥青质发生了相互作用。UPC-O 可在沥青质原位硫化为活性组分,对沥青质在悬浮床加氢裂化反应中的缩合起到好的抑制作用。     

油基钻井液的推广及循环利用

针对普通水基钻井液在钻进中强、强水敏性油藏时会造成储层污染、产量降低的问题,指出了油基钻井液在钻进该类油藏时的优势和其成本高、对生态环境有污染的缺点。为了大面积推广应用油基钻井液,重点介绍了油基钻井液的特性和稳定性影响因素,并通过室内评价证明了油基钻井液在油层保护中的良好效果,着重阐述了油基钻井液在王庄油田的现场应用情况,并探讨了油基钻井液的循环利用技术。研究结果表明,油基钻井液不仅具有良好的油层保护效果,而且具有较好的社会经济效益。     

贵冶动力中心二期反渗透系统改造

本文阐述对贵冶动力车间二期反渗透进行改造的成功实践 ,主要从反渗透系统设计、反渗透系统中容易出现的问题及解决方法等进行介绍。     

天津德景住宅与商业

因：用地为东西向长达470m的长条形，其北侧紧邻城市干道。     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

Development of an end-point detector for parylene deposition process

Parylene is an emerging material for MEMS. It is an organic material that is grown by using the chemical vapor deposition method at room temperature. The deposition thickness is commonly controlled by the amount of solid-phase dimer loaded in a sublimation chamber. In a conventional deposition machine, the end point of the process is designated by the moment the dimer is exhausted. However, this end-of-process criterion does not offer precise, repeatable control of film thickness. We present the results of the development of an in situ end-point detector for a Parylene chemical vapor deposition process. The detector is based on the thermal transfer principle and can be implemented on commercial parylene deposition systems with minimal system modification. Such a sensor enables a user to stop the deposition when a targeted thickness is reached. The end point detector is very simple to implement on existing parylene deposition systems. A series of such sensors with different target deposition thickness would allow extraction of the actual deposition rate within a deposition run.     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

Piezoelectric Nanogenerators for Self-Powered Nanodevices

A novel approach converts nanoscale mechanical energy into electric energy for self-powering nanodevices.In our own work, we've used piezoelectric zinc-oxide nanowire (ZnO NW) arrays to demonstrate a novel approach for converting nanoscale mechanical energy into electric energy. Here, we review the fundamental principle behind the nanogenerator, present an approach for improving its performance, and discuss some of the challenges we face in pushing this technology to reach its potential.     

Hydrothermal Synthesis of Magnesium Aluminate Platelets

Magnesium aluminate (MgAl₂O₄) platelets were first synthesized by hydrothermal treatment of γ-AlO(OH) in a magnesium nitrate aqueous solution at 400°C. The platelets are 100–200 nm in width and 25 nm in thickness. The influence of temperature, the anions of the magnesium salt, the amount of magnesium salt, and precursor pH on the formation of such structure was investigated. The experimental results indicated that the anions of the magnesium salt and precursor pH could have a significant influence on the growth of MgAl₂O₄. MgAl₂O₄ formation followed the in situ transformation mechanism, which was the reason why the MgAl₂O₄ crystallites had a platelet morphology.     

ROADM技术发展与标准化研究

本文研究了ROADM的技术优势，主要结构类型，涉及的关键技术以及存在的问题，并分析了当前ROADM标准化进展情况与发展趋势，还介绍了当前设备现状和现网应用情况。