Production and properties of micro‐porous glas bubble zinc and aluminium composites

Micro‐porous syntactic foams were produced by means of integration of glass bubbles into aluminium and zinc matrices. Preforms of glass bubbles were pressure infiltrated with the alloys AlSi9Cu9 ans ZnAl4Cu using squeeze casting. The preforms were sintered thermically without the use of bonding agents. Using the combination of different sintering steps syntactic foams with locally different densities could be produced. The mechanical properties of the foams were tested indicating a high compression strength of the foams and a very good compression energy absorption. Furthermore, corrosion behaviour and behaviour at higher temperatures were investigated.     

Aerodynamic effect on natural frequency and flutter instability in rotating optical disks

 Experimental studies on the aerodynamic coupling effect on natural frequencies and flutter instability of rotating disks are investigated in this paper. The experiments performed using a vacuum chamber and optical disks give two main results. One is that the aerodynamic effect by surrounding air reduces the natural frequencies and critical speeds of the vibration modes in pre-flutter regions. The other is that the natural frequency of the disk rotating at ambient atmospheric pressure is equal to that in vacuum at the flutter onset speed where the disk experiences aero-induced flutter. In post-flutter regions, the aerodynamic coupling between the disk and surrounding air increases the natural frequencies of the disk. Received: 17 June 2002/Accepted: 7 October 2002 The work was supported by Grant No. R11-1997-042-090001-0 of the Center for Information Storage Devices designated by the Korea Science & Engineering Foundation. Paper presented at the 13th Annual Symposium on Information Storage and Processing Systems, Santa Clara, CA, USA, 17–18 June, 2002     

On the current delivery limit of semiconducting carbon nanotubes

The current carrying capacity of single-walled semiconducting carbon nanotubes (CNTs) is studied by self-consistent quantum simulations using the non-equilibrium Green’s function formalism with the self-consistent Born approximation. The simulation shows that the current carrying capacity depends on the bias regime and is drastically different from that of metallic tubes. For long CNTs (with a length much longer than zone boundary and optical phonon scattering mean free path), the current saturates around 20 μA in the forward bias regime with unipolar transport due to phonon scattering. In ambipolar transport regime, the current delivery limit is still about 20 μA due to recombination of electron and hole currents. In contrast, for short semiconducting CNTs, the current delivery capacity can be above 25 μA in the unipolar transport regime and further double in the ambipolar transport regime. In reverse bias regime, the current of a long CNT can exceed 20 μA due to the second subband conduction and increased electron injection from the drain. The simulation provides a coherent explanation to the dependence of current delivery limit on bias regime and channel length, which is consistent with recent experiments.     

From information to probability: An axiomatic approach—Inference is information processing

We define the very rich language of composed conditionals on a three‐valued logic and use this language as the communication tool between man and machine. Communication takes place for three reasons: knowledge acquisition, query, and response. Learning, thinking, and answering questions are of a pure information theoretical nature. The pivot of this knowledge processing concept is the amount of information (bit) we receive if a conditional becomes true. We follow an axiomatic approach to information theory rather than the classical probabilistic approach of Shannon; information comes first, and then comes probability. In the light of this philosophy, query and response experience new interpretations. Both, acquisition and response are realized by maximizing entropy and minimizing relative entropy, respectively. The iterative solution of these mathematical optimization problems gives new insights into the adaptation of prior knowledge to new information. Our expert system shell SPIRIT supports this kind of knowledge processing, which will be established by suitable examples. © 2003 Wiley Periodicals, Inc.     

Prediction of fire classification for wood based products. A multivariate statistical approach based on the cone calorimeter

Wood has long traditions as a building material, and is often used in construction elements, and as interior and exterior surfaces in the Nordic countries. In most applications, there are reaction to fire requirements to products used as surfaces, e.g. in escape routes and larger public spaces. Most wood products will therefore have to be treated with fire retardant (FR) agents to fulfil the strict requirements to properties connected to heat release and flame spread. Unfortunately, FR agents usually also increase the smoke production, as they cause a more incomplete combustion of the wood. The wood product manufacturers seek to find the optimal amount of FR additives where both heat release and smoke production in the classifying test are within the requirements given in the building regulations. This paper describes models for prediction of the European reaction to fire classes of wood products. The models are based on multivariate statistical analysis, and use test results from the cone calorimeter test as input. The presented models are, with very good precision, able to predict which Euroclass and additional smoke class a wood based product would obtain if it were to be tested in the single burning item test. Copyright © 2006 John Wiley & Sons, Ltd.     

Efficiency increase of an induction motor by improving coolingperformance

Improving the efficiency of induction motors, which are the most energy consuming electric machines in the world, saves much energy. The efficiency can be increased by improving cooling performance as well as by using better materials or by improving electromagnetic performance with better design. This paper presents the relationship between the efficiency or the losses and the temperature of coils with experiments as well as simulations by changing parameters such as the load and the flow rate of cooling air. The losses and the efficiency are calculated from an equivalent circuit method as well as experiments. Coil temperatures variation affects much on the efficiency. The internal cooling method is better than that of external cooling for the coil temperature reduction. Several cooling methods are compared focusing on the fan efficiency and performance, from which the values of the efficiencies of the motors are expected. The fan efficiency as well as the fan performance should be considered for the optimum fan design to increase the total efficiency of a motor. The simulations are validated by the comparison with the experiments     

Call admission control schemes under generalized processor sharing scheduling

Provision of Quality‐of‐Service (QoS) guarantees is an important and challenging issue in the design of integrated‐services packet networks. Call admission control is an integral part of the challenge and is closely related to other aspects of networks such as service models, scheduling disciplines, traffic characterization and QoS specification. In this paper we provide a theoretical framework within which call admission control schemes with multiple statistical QoS guarantees can be constructed for the Generalized Processor Sharing (GPS) scheduling discipline. Using this framework, we present several admission control schemes for both session‐based and class‐based service models. The theoretical framework is based on recent results in the statistical analysis of the GPS scheduling discipline and the theory of effective bandwidths. Both optimal schemes and suboptimal schemes requiring less computational effort are studied under these service models. The QoS metric considered is loss probability. This revised version was published online in June 2006 with corrections to the Cover Date.     

Mode I interlaminar fracture toughness of commingled carbon fibre/PEEK composites

Carbon fibre/poly (ether-ether-ketone) (PEEK) composites were fabricated from plain weave cloth using the commingled yarn of carbon fibres with PEEK filaments. The undirectional specimen was made from the warp of commingled yarn and the weft of PEEK yarn, while the two-dimensional specimen was made from commingled yarns both of the warp and the weft. During the hot-pressing process, PEEK filaments melt to form the matrix of the composite. The interlaminar fracture toughness of the commingled composite was measured and compared with that of the prepreg composite. The critical strain energy release rates,/'G _Ics, obtained for the commingled composites were higher than the prepreg composite. In particular, the two-dimensional composite exhibited higherG _Ic than the unidirectional commingled composite. Factors increasing the fracture toughness of commingled composites have also been investigated by SEM observation of the fractured surface.     

Variation in Malting Quality and Heat Resistance in the Malting Barley Variety “Alexis”

In earlier studies concerning vigour, where subsamples are heat‐treated before germination there was found heat‐sensitive as well as heat‐resistant barley samples. The vigour model developed by Ellis and Roberts and further developed at Carlsberg, could only describe the heat‐sensitive barleys. Seventeen samples of the “Alexis” variety grown widely in Europe were collected from the EBC trials in 1994 in order to see if heat resistance in barley was influenced by different growing conditions. We found both heat‐sensitive samples following the vigour model as well as pronounced heat‐resistant samples, but these were not divided according to growing conditions. The germination curves dependent on heat treatment and germination time were evaluated by Principal Component Analysis (PCA). Heat‐resistant barley samples could be differentiated from heat‐sensitive samples already after ½ h of heat treatment at 68°C (12% moisture) and after 3 days of germination. The barley samples were analysed with regard to malting quality. The PCA evaluation of the data divided the samples according to growing location, mainly due to differences in protein and β‐glucan. However, the malting analyses could not describe the differences in heat resistance and sensitivity of the barleys. The biochemical background of the heat resistance found is discussed on the basis of literature. Our findings should give an experimental basis for exploiting a biochemical principle for heat resistance, which is formed during grain filling and consumed during storage and germination.     

Investigation of Scale Formation in Heat Exchangers of Phosphoric Acid Evaporator Plants

The primary problem in concentrating phosphoric acid is due to fouling on the tube‐side of the heat exchangers of the evaporator units. Scaling on the heat transfer surfaces occurs because of high supersaturation of phosphoric acid liquor with respect to calcium sulphate. A review of the existing literature reveals that no information is available on heat transfer and on crystallization fouling of industrial phosphoric acid solutions. In this investigation, the solubility of different calcium sulphate types in phosphoric acid solution was studied and its dependency on acid concentration and temperature was investigated. A large number of fouling experiments were carried out in a side‐stream of a phosphoric acid plant at different flow velocities, surface temperatures and concentrations to determine the mechanisms, which control the deposition process. After identifying the effects of operational parameters on the deposition process, a model was developed for prediction of fouling resistances. The reaction of calcium sulphate crystallization followed a second order rate with respect to the supersaturation. The activation energy evaluated for the surface reaction of the deposit formation was found to be 57 kJ/mol. The predicted fouling resistances were compared with the experimental data. Quantitative and qualitative agreement between measured and predicted fouling rates is good.