A rubber-modified thermoplastic where the morphology produced by phase-separation induced by polymerization disappears at high conversions

An unexpected experimental finding is reported where the primary morphology developed during polymerization-induced phase separation in a rubber-modified thermoplastic practically disappears at high conversions. This process was evidenced by light scattering (LS) and scanning electron microscopy (SEM) for a particular composition of solutions of polyisobutylene oligomers (PIB) in isobornylmethacrylate (IBoMA), during the free-radical polymerization of the monomer. The primary phase separation produced a dispersion of domains rich in PIB containing significant amounts of the monomer (IBoMA). Polymerization of the monomer in these domains occurred at high overall conversions producing the filling of dispersed domains with a PIBoMA-PIB blend that could not be distinguished from the matrix. Under these conditions the final material had the appearance of a homogeneous blend.     

Exit effect on hydrodynamics of the internal circulating fluidized bed riser

This is the first time an extensive investigation has been carried out regarding the effects of riser exit geometry on pressure drop and solid behaviour inside the Internal Circulating Fluidized Bed (ICFB) riser, using different riser exit geometries at several operating conditions.The Radioactive Particle-Tracking (RPT) technique was used for solid concentration measurements and solid residence time distribution at the exit zone. Experiments were conducted using Geldart B particles, in the gas superficial velocity range of 4 to 10 m/s. Axial solid hold-up, solid residence time distribution in the exit zone, and the reflux ratio factor k_m, (defined earlier by [E.H. Van der Meer, R.B. Thorpe, J.F. Davidson, Flow patterns in the square cross-section riser of a circulating fluidized bed and the effect of riser exit design, Chem. Eng. Sc. 55 (19) (2000) 4079-4099]), were the main criteria used to investigate the impact of gas-solid separator devices implemented at the ICFB riser exit.Solid residence time distribution results and axial solid hold-up profiles provided clear evidence that the separator device at the riser exit strongly influences the hydrodynamic structure of the ICFB riser. The V-shaped riser exit geometry was found to be the optimum of all the configurations studied.     

Integrated carbon nanotube field emission differential amplifier: Modeling and measurement of the common-mode rejection ratio

A novel integrated vacuum field emission (VFE) differential amplifier (diff-amp) utilizing carbon nanotube (CNT) emitters has been developed. A dual-mask microfabrication process was employed to achieve a VFE diff-amp by integrating identical CNT VFE transistors with built-in split gates and integrated anodes. The identical pair of triode amplifiers was well-matched in their device characteristics. The measured ac small-signal characteristics of the diff-amp showed a common-mode-rejection ratio (CMRR) of ~ 320 (~ 50 dB). The proposed analytical model of the CMRR was verified to be in good agreement with the experimental data. The successful implementation of the CNT diff-amp demonstrates a new way to achieve temperature and radiation tolerant VFE integrated microelectronics.     

Sprinklered office fire tests

This paper presents data relating to the performance of sprinklers and detectors in real office fire situations. For sprinklers, these data are additional to that associated with the standardized testing used to determine the design delivery density and pressure requirements for various occupancy situations, and provide a useful insight into the effect of sprinklers on developing fires with various office situations. The data given in this paper include the times for activation of various types of sprinkler heads (normal and fast response), the efficacy of the systems as far as extinguishment is concerned, estimates of the maximum size of the fires prior to commencement of extinguishment and associated air temperatures at various locations within the office enclosures. Copyright © 2008 John Wiley & Sons, Ltd.     

Separating n-alkane mixtures by exploiting differences in the adsorption capacity within cages of CHA, AFX and ERI zeolites

The saturation capacity of n-alkanes in CHA, AFX and ERI zeolites, that consist of cages separated by windows, decreases with increasing carbon number. The major aim of the present communication is to demonstrate the possibility of separating n-alkane mixtures relying on differences in saturation capacities. To investigate this possibility, Configurational-Bias Monte Carlo simulations for adsorption of C3–nC6, nC4–nC6, and nC5–nC6 mixtures in CHA, AFX and ERI were carried out for equimolar bulk fluid phase. These mixture simulations show that for operation at fluid phase fugacities below about 1 MPa, the adsorbed phase in equilibrium with the bulk vapor phase is predominantly the alkane with the longer chain length, i.e. nC6. However, for operation at pressures in excess of 1 MPa, the adsorbed phase in equilibrium with the bulk liquid phase is richer in the component with the smaller chain length. In some cases, the nC6 is practically excluded from the zeolite.     

X-ray microfluorescence analysis of pigments in decorative paintings from the sarcophagus cartonnage of an Egyptian mummy

This work characterized the elemental composition of the pigments used in decorative paintings from the sarcophagus cartonnage fragments of an Egyptian mummy, using μXRF with Synchrotron Radiation. This female mummy (n.158) is considered one of the most important pieces of the National Museum (Rio de Janeiro, Brazil) because of its unconventional embalming with legs and arms swathed separately. The measurements were performed at the XRF beamline D09B of the Brazilian Synchrotron Light Laboratory (LNLS), using white beam and a Si(Li) detector with resolution of 165 eV at 5.9 keV. The elements found in the samples were: Si, S, Cl, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, As, Sr, Hg and Pb.     

Validity of the Parabolic Effective Mass Approximation in Silicon and Germanium n-MOSFETs With Different Crystal Orientations

This paper investigates the validity of the parabolic effective mass approximation (EMA), which is almost universally used to describe the size and bias-induced quantization in n-MOSFETs. In particular, we compare the EMA results with a full-band quantization approach based on the linear combination of bulk bands (LCBB) and study the most relevant quantities for the modeling of the mobility and of the on-current of the devices, namely, the minima of the 2-D subbands, the transport masses, and the electron density of states. Our study deals with both silicon and germanium n-MOSFETs with different crystal orientations and shows that, in most cases, the validity of the EMA is quite satisfactory. The LCBB approach is then used to calculate the values of the effective masses that help improve the EMA accuracy. There are crystal orientations, however, where the 2-D energy dispersion obtained by the LCBB method exhibits features that are difficult to reproduce with the EMA model.     

Effects of thermal and mechanical treatments on a titanium-based conversion coating for aluminium alloys

The influence of mechanical deformation and heating on the protective performance of a chromium-free conversion treatment for aluminium alloys has been assessed by polarisation and AC impedance measurements. Protection is unlikely to be seriously compromised by typical production operations.     

Pheromone Disruption of Argentine Ant Trail Integrity

Disruption of Argentine ant trail following and reduced ability to forage (measured by bait location success) was achieved after presentation of an oversupply of trail pheromone, (Z)-9-hexadecenal. Experiments tested single pheromone point sources and dispersion of a formulation in small field plots. Ant walking behavior was recorded and digitized by using video tracking, before and after presentation of trail pheromone. Ants showed changes in three parameters within seconds of treatment: (1) Ants on trails normally showed a unimodal frequency distribution of walking track angles, but this pattern disappeared after presentation of the trail pheromone; (2) ants showed initial high trail integrity on a range of untreated substrates from painted walls to wooden or concrete floors, but this was significantly reduced following presentation of a point source of pheromone; (3) the number of ants in the pheromone-treated area increased over time, as recruitment apparently exceeded departures. To test trail disruption in small outdoor plots, the trail pheromone was formulated with carnuba wax-coated quartz laboratory sand (1 g quartz sand/0.2 g wax/1 mg pheromone). The pheromone formulation, with a half-life of 30 h, was applied by rotary spreader at four rates (0, 2.5, 7.5, and 25 mg pheromone/m²) to 1- and 4-m² plots in Volcanoes National Park, Hawaii. Ant counts at bait cards in treated plots were significantly reduced compared to controls on the day of treatment, and there was a significant reduction in ant foraging for 2 days. These results show that trail pheromone disruption of Argentine ants is possible, but a much more durable formulation is needed before nest-level impacts can be expected. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.